How do I replace the front drive axle?
Remove the front wheel from the side of the vehicle you are replacing the drive axle on. If you do not have an impact gun you can remove the center cap on the front wheel.
How do you remove a ball joint from a rear axle?
Depending on the age and condition of the tie rod end you may need to use a pickle fork or ball joint remover (red arrow) to separate the ball joint from the bearing housing. By removing the tie rod end and the ball joint the hub now has enough room to move forward while pressing the axle out.
How do I remove the rear axle from the hub?
Use a standard three arm press (red arrow) and push the axle out from the hub. Loosely install the axle bolt to use to push against it. With the hub loose the axle can easily be separated from the hub.
How do you remove the rear axle from a Toyota Corolla?
Use a standard three arm press (red arrow) and push the axle out from the hub. Loosely install the axle bolt to use to push against it. With the hub loose the axle can easily be separated from the hub. Fully remove the six 12-point bolts from the flange and remove the axle from the car.
Can you change an axle yourself?
You absolutely can replace your CV axle at home, but you'll need to be at least remotely comfortable using a jack, jack stands, and power tools. Assuming you have most of the equipment already set up in your garage at home, the cost to replace your CV axle will be quite reasonable.
How do you change a CV axle on a VW?
0:069:13MK4 Volkswagen CV Axle Removal and Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipHead in order to remove your excellent. You need a 30 millimeter 12 point socket I have a 17 MillettMoreHead in order to remove your excellent. You need a 30 millimeter 12 point socket I have a 17 Millett here to remove my lug nuts.
How do you replace CV axles?
2:144:10How to Replace a CV Axle in Your Car - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut all the bolts back. In tighten off huh then tighten the axle nut. Huh. I put the tie rod back onMorePut all the bolts back. In tighten off huh then tighten the axle nut. Huh. I put the tie rod back on then get the nut and put it on the end of the tie right here. Make it nice and tight.
What is the easiest way to remove a CV axle?
You can use a small pry bar or sturdy flathead screwdriver to pry the axle from the joint.If the axle doesn't immediately come loose, try twisting it back and force to break the seal.It's normal for some transmission fluid to leak out as you remove the axle from the cv joint.More items...
How do you change a CV joint on a VW Golf?
0:087:15VW Golf Jetta Driveshaft CV Joint Removal Simple Easy StepsYouTubeStart of suggested clipEnd of suggested clipSo just loosen the drive shaft to send us the center bolt here just so when you actually come toMoreSo just loosen the drive shaft to send us the center bolt here just so when you actually come to release knee is whole lot easier. Now it's time to Jack the vehicle up.
How long does it take to change a CV joint?
between one and a half to three hoursReplacing a CV axle is a maintenance item that usually takes between one and a half to three hours to complete, depending on the vehicle and if other repairs are needed. A CV axle typically lasts for 70,000 to 130,000 miles, but the axles should be inspected for damage regularly.
Is it hard to replace an axle?
Replacing a front-wheel-drive axle is straightforward, although physically demanding. Get the replacement axle before you start, as well as a new spindle nut and a cotter pin or two.
How do you remove a CV axle without a puller?
0:020:49How to remove a STUCK CV AXLE (No slide hammer required)YouTubeStart of suggested clipEnd of suggested clipSo you're gonna press it right against right there of course you're supposed to do it with two handsMoreSo you're gonna press it right against right there of course you're supposed to do it with two hands then on the bottom you're gonna tap it with a hammer. Just gonna slowly tap. It.
What tools do I need to change a CV axle?
Tools and Equipment Needed to Replace a CV AxleBreaker bar.Dead-blow hammer.Drain pan.Jack and jack stands.Large hammer or mallet.Long-handled diagonal cutting pliers.Pry bar or CV axle puller.Ratchet and socket set.More items...•
Should I replace both CV axles at the same time?
On a high-mileage vehicle with a bad CV joint or boot, it's often a good idea to replace both shafts at the same time. Often, the right (passenger side) shaft fails first because right turns are at a sharper angle than left turns, and right turns are more common than left turns.
How do you pop a CV axle back in?
1:443:43How to Fix Stretched and Disconnected Inner CV Axle JointYouTubeStart of suggested clipEnd of suggested clipSo I'm going to try to finesse. This. And get this to line up. Here. So I think on most of theseMoreSo I'm going to try to finesse. This. And get this to line up. Here. So I think on most of these it's going to be pressing. It outwards. And there we go. And now we can flip our boot. Over.
Can you put a CV axle in wrong?
Wrong Axle, Bad Engineering If the axle is too long, it can cause the CV or plunge joint to bottom out and damage the surfaces of the balls, bearings and races. If it's too short, the axle could pull out of the plunge joint under certain conditions.
Like many modern manufacturers Volkswagen shares components and even platforms across its many model lines
This article is based on one of those shared components but the work may have been performed on a different model than your vehicle. While some fasteners and other hardware types and sizes may be different, all of the information you need to safely complete the project is included in this article.
Project Photos
Figure 1 If you do not have an impact gun you can remove the center cap on the front wheel. Leave the car on the ground and insert the 27mm socket through the center (red arrow). Next, place the largest breaker bar you have on the socket and break the bolt loose.
