- Make sure the golf cart is turned off, the transition is in neutral, and the brakes are locked. Hit the gas pedal to make sure that it is off.
- If the drive belt is loose you can remove it very easily by pulling it off the rear and starter clutch.
- If it’s too hard to do so, you can simply use a screwdriver and place it under the drive belt as a lever while rotating the clutch and it will ...
How do you replace the belt on a golf cart?
Raise the golf cart engine cover, to access the drive belt inside the engine compartment. The drive belt is plainly visible. Loosen the drive belt tension bolt, with the open end wrench, on the front pulley.
What does a drive belt do on a golf cart?
To primary function of a golf cart drive belt is to connect the primary clutch and the secondary clutch. The primary clutch drives the cart and the belt helps it to rotate the secondary clutch (they are referred to as the drive clutch and the driven clutch respectively). The drive belt, unlike some of the other automotive belts, are very thick.
How do I know if my golf cart drive belt is bad?
The best test to see if a golf cart drive belt has the correct tension is to use the Finger Test. Press the drive belt with one finger at its center between the two clutches. It should sag by just an inch and a half. Another method suggested by an expert is to go for a drive belt that is 1-inch shorter than the stock belt in your cart.
How to replace a clutch on a golf cart?
Switch OFF the golf cart’s engine. Take a screwdriver and gently insert it between the belt’s bottom and the clutch’s groove. Slowly rotate the clutch and the belt will come off easily. If the belt is already loose, taking it out is very easy.
When should a golf cart belt be replaced?
Over time, such belts can become dry and cracked, or may even break. If the cart is having trouble accelerating or will not engage at all, it may be because the belt needs changing. Park the golf cart, and turn off the engine. Raise the golf cart engine cover, to access the drive belt inside the engine compartment.
How Loose Should a golf cart belt be?
0:012:00How to Check the Belts in your Gas Golf Cart | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipDown below and you don't want to press the moderate pressure on that belt you're gonna want to seeMoreDown below and you don't want to press the moderate pressure on that belt you're gonna want to see about 3/16 to 1/4 inch of deflection. There no more than that that'll be your proper.
How do you change the drive belt on a club car?
5:269:16Club Car DS Tune Up Kit | Starter/Drive Belt - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou have to loosen all the bolts up the two up front which are 9/16 and loosen the adjustment bolt.MoreYou have to loosen all the bolts up the two up front which are 9/16 and loosen the adjustment bolt. Here which is a half-inch. So let's get these things loosened. Up.
How do you change a drive belt on a Yamaha g14 golf cart?
0:352:32HOW TO CHANGE A DRIVE BELT ON YAMAHA GOLF CART OR ANY ...YouTubeStart of suggested clipEnd of suggested clipJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spinMoreJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spin the back off.
How tight should golf cart starter belt be?
The drive belt should not be too tight. If it's too tight it can risk wearing off faster and it's also harder to shift gears. To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger.
How do you measure a golf cart belt?
0:002:04How to measure for a go-kart drive belt. - YouTubeYouTubeStart of suggested clipEnd of suggested clipCover. Now the first measurement we're going to take on this is we're going to measure from theMoreCover. Now the first measurement we're going to take on this is we're going to measure from the centerline of the crankshaft. To the centerline of the jack shaft.
How does a golf cart clutch work?
Both golf cart clutches look similar to a large pulley but each clutch has a sliding sheave that moves in & out along a central shaft as the clutch spins. The other sheave is fixed to either the crankshaft or the differential input shaft and it does not slide, it just spins.
How do you grease a Club Car Precedent?
0:282:11Club Car Golf Carts - Lubrication Schedule - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're going to want to actually feet see how the grease comes out of there fitting. Watch when IMoreYou're going to want to actually feet see how the grease comes out of there fitting. Watch when I push this see how it comes out you want to be able to see grease coming out of the fitting.
How do I replace the belt on my electric golf cart?
1:195:57Changing the Drive Belt and Starter Generator Belt 2008 EZGO TXTYouTubeStart of suggested clipEnd of suggested clipDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back.MoreDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back. Until it pops off that rear driven clutch and then take it right out.
How do you change a belt on a Yamaha golf cart?
0:563:28Yamaha Drive 2 Quietech G29 Drive Belt Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst and then you can remove it from the front clutch make sure that your cart is in neutral. SoMoreFirst and then you can remove it from the front clutch make sure that your cart is in neutral. So the cart can freewheel back and forth without turning the clutch.
What is a drive belt in a golf cart?
The golf cart drive belt is the larger (1" to 1 3/16" wide), longer and usually looser belt on gas golf cars. It connects the drive clutch (on the engine) to the driven clutch (on the differential) and transfers the power of the engine to the rear wheels.
How do you change a starter belt on a Yamaha golf cart?
0:435:12Yamaha G2, G9 Drive and Starter Belt Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just rolling it right over. It's that simple that was a little twisting a little tugging. ThatMoreAnd just rolling it right over. It's that simple that was a little twisting a little tugging. That will come right on. Now. We do this lift it from around the clutch.
How to change the belt on a golf cart?
Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
Why does my golf cart not engage?
If the cart is having trouble accelerating or will not engage at all, it may be because the belt needs changing. Park the golf cart, and turn off the engine.
How to check if golf cart drive belt is too tight?
To check if the drive belt is too tight, follow these steps: Switch OFF the golf cart ’s engine. Reach to where the drive belt is located and use your fingers to press the drive belt between the two clutches. The belt must deflect at least one and a half inches under the pressure of your fingers.
What happens if a golf cart belt is too tight?
If the belt is too tight then your starter will be under strain and this should be avoided. The best test to see if a golf cart drive belt has the correct tension is to use the Finger Test.
How to tell if a 1997 club car has a slipping drive belt?
When a 1997 Club Car drive belt is slipping, first make sure that it is the drive belt that is at fault. You may have to remove the cover and watch the clutches in action while the cart is in motion to make sure that it is indeed the drive belt that is slipping.
How to remove drive belt?
Removing the drive belt involves holding the belt with both hands in the center between the driven and drive clutches and lifting the belt. You must now rotate the driven clutch counter-clockwise and slip the belt off the sheave. You can then slide the drive belt off the drive clutch.
Why is my club car drive belt so tight?
The reason for a Club Car drive belt being too tight can be because the drive belt is too small for the golf cart. The way to check if the belt is fitted correctly is to push the belt down with one finger at the center between the clutches. It should not deflect more than 1.5inches. It should not be less as well.
What is the primary function of a golf cart drive belt?
To primary function of a golf cart drive belt is to connect the primary clutch and the secondary clutch. The primary clutch drives the cart and the belt helps it to rotate the secondary clutch (they are referred to as the drive clutch and the driven clutch respectively). The drive belt, unlike some of the other automotive belts, are very thick.
Why does my golf cart drive belt slip?
The reason for the drive belt slipping could be that it is of a larger/longer size and therefore loose. You may start feeling the slippage after driving for a while. This is because the belt gets heated up after the golf cart runs for some time and loosens further .
