Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
How to change drive belt on a club car golf cart?
How to Change the Drive Belt on a Club Car Golf Cart Switch the engine OFF after parking the golf cart.. Allow the engine to cool, if it has been running for some time.. Remove the engine cover.. You will be able to see the drive belt now.. Use an open-end wrench to loosen the drive belt tension ...
How do I know if my golf cart drive belt is bad?
The best test to see if a golf cart drive belt has the correct tension is to use the Finger Test. Press the drive belt with one finger at its center between the two clutches. It should sag by just an inch and a half. Another method suggested by an expert is to go for a drive belt that is 1-inch shorter than the stock belt in your cart.
How to replace a clutch on a golf cart?
Switch OFF the golf cart’s engine. Take a screwdriver and gently insert it between the belt’s bottom and the clutch’s groove. Slowly rotate the clutch and the belt will come off easily. If the belt is already loose, taking it out is very easy.
Why is my club car drive belt too tight?
The reason for a Club Car drive belt being too tight can be because the drive belt is too small for the golf cart. The way to check if the belt is fitted correctly is to push the belt down with one finger at the center between the clutches. It should not deflect more than 1.5inches. It should not be less as well.
How do you change the drive belt on an EZGO golf cart?
1:195:57Changing the Drive Belt and Starter Generator Belt 2008 EZGO TXTYouTubeStart of suggested clipEnd of suggested clipDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back.MoreDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back. Until it pops off that rear driven clutch and then take it right out.
How tight should a golf cart drive belt be?
The reason for a Club Car drive belt being too tight can be because the drive belt is too small for the golf cart. The way to check if the belt is fitted correctly is to push the belt down with one finger at the center between the clutches. It should not deflect more than 1.5inches.
How do you remove a drive belt?
1:223:48Gilson Test-Master® DIY Series: Replacing the Drive Belt - YouTubeYouTubeStart of suggested clipEnd of suggested clipSlide the motor carefully. Towards the center of the unit. This will relieve tension on the driveMoreSlide the motor carefully. Towards the center of the unit. This will relieve tension on the drive belt slip the drive belt off the pulleys and replace it with a new drive belt.
When should a golf cart belt be replaced?
Over time, such belts can become dry and cracked, or may even break. If the cart is having trouble accelerating or will not engage at all, it may be because the belt needs changing. Park the golf cart, and turn off the engine. Raise the golf cart engine cover, to access the drive belt inside the engine compartment.
How do I know if my golf cart belt is too loose?
0:012:00How to Check the Belts in your Gas Golf Cart | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipDown below and you don't want to press the moderate pressure on that belt you're gonna want to seeMoreDown below and you don't want to press the moderate pressure on that belt you're gonna want to see about 3/16 to 1/4 inch of deflection. There no more than that that'll be your proper.
How do I stop my golf cart belt from squeaking?
Your belt may also be wearing down and even fraying which is a problem that can cause the belt to both squeak and whine as it runs. Replace any frayed belts right away, before they break, to avoid damaging your engine, and lubricate or replace any pulleys which continue to squeak on your cart.
How long does it take to replace a drive belt?
It can take anything from 15 minutes to an hour (two at the most) to repair or replace a bad serpentine belt with a new belt.
How do you remove a belt without a tensioner?
0:142:00DIY - Install and remove stretch fit belt without special tools - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd loop the belt over the pulley with the deepest. Shoulder. In this application that would be theMoreAnd loop the belt over the pulley with the deepest. Shoulder. In this application that would be the water pump since the camshaft pulley rotates counterclockwise.
How do you put a belt on a belt drive?
1:032:15Supercheap Auto - YouTubeYouTubeStart of suggested clipEnd of suggested clipSure that it's properly seated in the v-shaped groove or the multiple grooves in the pulleyMoreSure that it's properly seated in the v-shaped groove or the multiple grooves in the pulley depending on its construction. If the belt is serpentine.
How do you measure golf cart belts?
0:002:04How to measure for a go-kart drive belt. - YouTubeYouTubeStart of suggested clipEnd of suggested clipCover. Now the first measurement we're going to take on this is we're going to measure from theMoreCover. Now the first measurement we're going to take on this is we're going to measure from the centerline of the crankshaft. To the centerline of the jack shaft.
What is a drive belt in a golf cart?
The golf cart drive belt is the larger (1" to 1 3/16" wide), longer and usually looser belt on gas golf cars. It connects the drive clutch (on the engine) to the driven clutch (on the differential) and transfers the power of the engine to the rear wheels.
Can you adjust a golf cart clutch?
If you are unsure about removing the drive belt or the clutch, then you can adjust it. Just take out the belt and wound it again with the secondary clutch according to the requirements, and your problem should be fixed.