Golf Club Shaft and Club Head Replacement
- Step 1 Golf Club Steel Shaft and Grip. Using propane or a torch, heat the hosel of the club to remove the steel shaft...
- Step 2. Use a wire brush to clean out the remains of the old epoxy from the club head.
- Step 3. Use a piece of sand paper or a grinder to roughen the tip of the shaft where it connects to the hosel of the...
How do you remove steel shafts from a golf club head?
Using propane or a torch, heat the hosel of the club to remove the steel shaft from the club head. The heat will break the epoxy bond that holds the head to the shaft.
Can you replace a golf club shaft yourself?
Instead of paying the pro shop the next time you need to change a golf club shaft, save money by doing it yourself at home. Make sure your replacement shaft is the same size as the original or it might not fit inside the club head's hosel.
How do you fix a broken hosel on a golf club?
Use a heat gun to heat up the area around the hosel to soften the epoxy glue that connects the shaft to the club head. Push on the base of the hosel with a pry bar to release the head from the shaft. Catch the head as it falls off the end of the shaft. Allow the club head to cool off before installing the new shaft.
Why won't my Shaft fit my club head?
Make sure your replacement shaft is the same size as the original or it might not fit inside the club head's hosel. The hosel is the junction point between the head and the tip of the shaft. Check the size with a shaft identification gauge if you cannot find it on the label.
Can you put any golf head on any shaft?
Yes, most golf Driver shafts are interchangeable. Golf driver shafts can be replaced as long as the new shaft is the same length and made by the same brand of golf club.
Is it easy to change golf shafts?
Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How do you put a golf club head on?
0:236:41HOW to FIX your GOLF CLUB if the HEAD comes off | Easy TutorialYouTubeStart of suggested clipEnd of suggested clipIf you want to just make sure you're getting the right thing basically just one side hardener. AndMoreIf you want to just make sure you're getting the right thing basically just one side hardener. And one side resin. And they mix together to form a really strong bond.
How do you change iron heads?
2:5922:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the shafts you don't need a shaft puller. Anything like that you can just heat them up andMorePull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
How do you remove a golf club head?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
Can I Reshaft my own golf clubs?
Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.
How do I install a driver head?
1:332:35Golf Equipment : How to Install Golf Club Heads on a Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we just literally take the take the shaft. And push it into that head until that epoxy comes outMoreSo we just literally take the take the shaft. And push it into that head until that epoxy comes out the top wipe the epoxy. Clean. Then let it dry mine i use 24-hour epoxy so we let that dry for 24.
What glue do you use for golf club heads?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
How do you remove a driver head from the shaft?
0:314:28How To Remove A Graphite Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat are commercially available but they do essentially the same thing they securely clamp the shaftMoreThat are commercially available but they do essentially the same thing they securely clamp the shaft. And either push or pull the head straight off that's the key.
What is the cost of Reshafting a golf club?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
Is it easy to Reshaft irons?
Golf irons can be a bit easier to reshaft than a driver. If you are reshafting with steel irons, it is usually pretty straightforward. However, you will need the proper tools and space to complete this project.
How do you remove a golf head from a graphite shaft?
0:015:40How to Remove a Golf Shaft | DIY project Graphite Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo i'm in my garage this morning. And what i want to show you is how to remove a um club head fromMoreSo i'm in my garage this morning. And what i want to show you is how to remove a um club head from the uh from a shaft. This particular one is a graphite shaft. So you got to be extra careful uh i did
Can you change shafts on irons?
If you're thinking about changing the shafts on your golf clubs, you can either do them yourself or take them to your local golf shop.
How much does it cost to replace a golf shaft?
Re-Shafting a Driver Golf shops can re-shaft a driver for as little as $20, but usually require that the shaft be purchased from the shop with the re-shafting provided as an additional service. Expect to pay more if you bring your shaft into a golf shop for re-shafting service.
Can you change shafts on drivers?
Replacing your old shaft can be a relatively painless process for you or your local repair shop. If your favorite old driver seems to have run out of quality hits, you might want to refresh it by adding a new shaft to the club.
How do you change golf shafts?
0:335:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool so we lay it in in this little groove right here. Which is going to slide back and forth andMoreTool so we lay it in in this little groove right here. Which is going to slide back and forth and put pressure and pull on the head. As the shaft is heated. Then we tighten the shaft.
How to prepare a club head for a new shaft?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris.
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
How to fix a club head that is stuck to the shaft?
Step 1. Scrape off the ferrule at the bottom of the club head's hosel with a utility knife. Place the club into a shaft clamp to hold it in place while you work on the head. Use a heat gun to heat up the area around the hosel to soften the epoxy glue that connects the shaft to the club head.
What is the hosel on a golf club?
The hosel is the junction point between the head and the tip of the shaft. Check the size with a shaft identification gauge if you cannot find it on the label.
How to remove epoxy from golf club?
Remove the club from the shaft clamp and tap the butt end of the grip on the floor to push the shaft all the way into the head. Wipe down the hosel with a soft cloth to remove any epoxy residue. Let the epoxy dry for several hours before using the golf club.
Can you replace a golf club shaft yourself?
It's usually best to consider having shaft replacement done by someone who knows what they are doing. Instead of paying the pro shop the next time you need to change a golf club shaft, save money by doing it yourself at home. Make sure your replacement shaft is the same size as the original or it might not fit inside the club head's hosel.
How to melt glue on a golf club?
Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue.
How to remove a ferrule from a hosel?
The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.
Do you need to reshaft a golf club?
The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.
