Golf-FAQ.com

how to change rear brakes 2013 golf r

by Paolo Stroman Published 3 years ago Updated 2 years ago
image

How do you replace the rear brake shoes on a Ford Ranger?

You can then use a ratchet to remove the axle bearing nut and pull off the brake drum. Then, pull off the brake shoe springs, clips, and cable so you can pull off the old brake shoes. Slide the new brake shoes into place and reconnect all of the springs, clips, and cables so you can replace the drum and axle.

How do I replace the drum on my front brakes?

Place the new drum over the brake shoe set and screw the axle nut on to hold it in place. A new drum is required to allow the brakes to seat properly onto the new braking surface.

How do I change brake shoes?

Even a novice can learn to change brake shoes, provided they have the right tools. Jack the vehicle up and remove the wheel. Park the vehicle on a firm, level surface.

Why replace the rear brake shoes on a car?

Replacing the rear brake shoes on a car will ensure that the brakes are in good working order and ready to function properly in the event of an emergency. You can learn how to change rear brake shoes in a professional manner to save yourself money and to help you understand your car better.

How to separate parking brakes from the backing plate?

Why do you need to replace rear brake shoes?

How to remove brake drum?

What to do if your rear brakes are squealing?

What is the center of a brake drum?

How to remove a rear wheel?

How to unscrew a bearing nut?

See more

About this website

image

How do you change the rear brake discs on a VW Golf mk7?

0:0715:56VW GOLF GTI MK7 - How To Replace Rear Brake Discs & Pads Change ...YouTubeStart of suggested clipEnd of suggested clipTools you'll need for the job a breaker bar with an m14 spline bit a seven mil allen key with aMoreTools you'll need for the job a breaker bar with an m14 spline bit a seven mil allen key with a ratchet a hammer flat screwdriver t30 torx a wire brush some brake cleaner and copper grease.

How do you retract rear caliper pistons?

6:407:45How to Retract a Rear Brake Piston in Caliper - Both Types Covered!YouTubeStart of suggested clipEnd of suggested clipThat's going to push the piston back into its housing. And then once it's fully recessed just stop.MoreThat's going to push the piston back into its housing. And then once it's fully recessed just stop. And check and you can verify that because the piston will be fully into the housing.

What brakes are on the Golf R?

Available for the Golf R and Golf R Variant are 'Performance' disc brakes. The brake system is two kilos lighter than the standard brakes and thereby reduces unsprung masses. Even on the racetrack the system is extremely stable. The front brake discs are what are known as 'built pin discs'.

How do you change brake pads on a Golf R?

0:006:18Volkswagen MK6 Golf R Front Brake Replacement (Pads and Rotors)YouTubeStart of suggested clipEnd of suggested clipAll the lug bolts loose while the car is on the ground. Next you have to remove the two bolts thatMoreAll the lug bolts loose while the car is on the ground. Next you have to remove the two bolts that hold the carrier to the hub we're getting the bottom one with the impact gun. Here.

How do you push rear brake piston without tool?

0:012:58How To Collapse Twist Style Rear Brake Caliper Without Special ToolYouTubeStart of suggested clipEnd of suggested clipAnd usually you'll go one way and you'll feel the piston going in and then you'll have to tightenMoreAnd usually you'll go one way and you'll feel the piston going in and then you'll have to tighten your vice grips you gotta be really careful not to pinch the boots in here.

How do you push a piston back without tool?

1:232:38How To Compress Rear Brake Caliper Piston - WITHOUT THE TOOL - HDYouTubeStart of suggested clipEnd of suggested clipWe'll kind of lock it into place and spin it clockwise. And what you'll start to notice is. It'llMoreWe'll kind of lock it into place and spin it clockwise. And what you'll start to notice is. It'll start to go in the Piston. Stuff finally go back into the housing. And. As we can tell.

How long do Volkswagen brakes last?

The average lifespan for most Volkswagen brake pads is 50,000 miles, but that number can vary based on how often you drive, the quality of the pads, how well you maintain your VW and your driving style.

What brand of brakes do VW use?

The brake pads come directly from TMD Friction. The company delivers its brand Pagid the manufacturer directly.

How long do GTI brakes last?

between 30,000 and 70,000 milesVW Golf GTI brake pads commonly last between 30,000 and 70,000 miles depending on your driving habits. If you travel to work in accomplished traffic and use your brakes naturally, you'll need to get an inspection more continuously.

How do you change the brakes on a mk7 GTI?

0:0712:52VW GOLF GTI MK7 - How To Replace Front Brake Discs & Pads Change ...YouTubeStart of suggested clipEnd of suggested clipTools you'll need for the job t30 torx wire brush flat screwdriver a 21 mil socket a 13 an 18 milMoreTools you'll need for the job t30 torx wire brush flat screwdriver a 21 mil socket a 13 an 18 mil spanner a g clamp a rubber mallet some brake cleaner and copper grease.

What is a Mk6 golf?

The Volkswagen Golf Mk6 (codenamed Typ 5K) is a compact car, the sixth generation of the Volkswagen Golf and the successor to the Volkswagen Golf Mk5. It was unveiled at the Paris Motor Show in October 2008 for the 2009 model year.

How do you release the electronic parking brake on an Audi?

With the AUTO switch OFF, the EPB can be applied by pushing and holding the parking brake switch. This will work with the ignition switch ON or OFF and with the vehicle moving or stationary. To release the brake, pull and hold the manual switch while at the same time pressing the brake pedal.

How to replace the rear brake shoes on a 2015 Mitsubishi - Fixya

SOURCE: how to change rear brake shoes on a 2004 chevy venture The rear brake shoes use a U clip to hold the shoes together. A simple solution to this change job is to change one side at a time. Slowly unclip the U clip from the top of the shoe and remove the left shoe and spring.

Installation Instructions for Replacement Brake Shoes

Each kit contains right side and left side primary and secondary brake shoes, replacement primary springs, replacement bearing grease caps and locking tab washer (disregard locking tab washer if your spindle/hub may uses a flat washer and cotter key).

Factory Drum Brake Shoe thickness between front and rear shoes

The rear drum brakes are of the leading & trailing shoe design; sort of like self-energizing & non-self energizing. The shoe towards the front of the car is the self energizing shoe and sees more friction than the rear non-self energizing shoe due to the anchor points at the bottom of the backing plate, hence the different thickness.

Gibbo205

I need some new rear pads for my MK7 Golf R and might as well grab disc too I found these:

dazie00

I have gone for EBC yellowstuff pads, seem pretty good imo , with M-tec c groove discs which don't rust!!

NeilM

Does this method work and is safe? I don't have the software or vagcom, hence a manual old school way is required.

Timmy Mallett

Personally I wouldn't touch ebc with a ten foot pole. Cheap crap that warps and I've had personal experience, on my own and friends cars. Admittedly it was a few years ago but I've only ever used OEM since.

Timmy Mallett

I don't think it's worth straying. Stuff like eBC and Ferodo are budget brands aimed at a certain type of customer and the braking was never as good as OEM.

Gibbo205

I purchased the car at a reduced price as the brakes were knackered when I got the car, fronts heavily warn and warped as they are the original disc from new, car has now done 38,000 miles.

Rob2k68

Just to add to this thread to say that you don’t need a wind back tool for the caliper it just pushes back in - pic in my build thread. Still requires VCDS or OBD11 to activate lining change mode.

How to separate parking brakes from the backing plate?

Pull the brake shoe set free from the backing plate. Grip the brake pads on either side and pull them directly toward you to separate them from the backing plate. The springs will come with the brake shoe set, but the parking brake cable should remain with the vehicle.

Why do you need to replace rear brake shoes?

Replacing the rear brake shoes on a car will ensure that the brakes are in good working order and ready to function properly in the event of an emergency. You can learn how to change rear brake shoes in a professional manner to save yourself money ...

How to remove brake drum?

Start by jacking up the vehicle and removing the wheel to access the brake drum behind it. You can then use a ratchet to remove the axle bearing nut and pull off the brake drum. Then, pull off the brake shoe springs, clips, and cable so you can pull off the old brake shoes.

What to do if your rear brakes are squealing?

Article Summary X. If your brakes are squealing or aren’t working as effectively, it’s time to change your rear brake shoes. In order to do so, you need to remove the brake drums so you can pull out the old brake pads and replace them with new ones.

What is the center of a brake drum?

The center of the circular brake drum is a removable dust cap. Slide a flat head screw driver into the gap beneath the dust cap and pry it toward you to remove it. The dust cap may have rusted in place or could be stuck due to brake dust and road grime.

How to remove a rear wheel?

Park the vehicle on a firm, level surface. Use a tire iron or the appropriate socket to loosen the lug nuts on the first rear wheel, then slide a jack beneath one of the vehicle’s rear designated jack points to lift the vehicle up.

How to unscrew a bearing nut?

Use a ratchet to unscrew the axle bearing nut. Beneath the dust cover, you’ll find the axle bearing nut. This large nut is usually a 22 or 24 millimeter metric socket, or a 7/8” standard socket. Use a breaker bar or half inch drive ratchet to turn the nut counterclockwise in order to remove it.

How to separate parking brakes from the backing plate?

Pull the brake shoe set free from the backing plate. Grip the brake pads on either side and pull them directly toward you to separate them from the backing plate. The springs will come with the brake shoe set, but the parking brake cable should remain with the vehicle.

Why do you need to replace rear brake shoes?

Replacing the rear brake shoes on a car will ensure that the brakes are in good working order and ready to function properly in the event of an emergency. You can learn how to change rear brake shoes in a professional manner to save yourself money ...

How to remove brake drum?

Start by jacking up the vehicle and removing the wheel to access the brake drum behind it. You can then use a ratchet to remove the axle bearing nut and pull off the brake drum. Then, pull off the brake shoe springs, clips, and cable so you can pull off the old brake shoes.

What to do if your rear brakes are squealing?

Article Summary X. If your brakes are squealing or aren’t working as effectively, it’s time to change your rear brake shoes. In order to do so, you need to remove the brake drums so you can pull out the old brake pads and replace them with new ones.

What is the center of a brake drum?

The center of the circular brake drum is a removable dust cap. Slide a flat head screw driver into the gap beneath the dust cap and pry it toward you to remove it. The dust cap may have rusted in place or could be stuck due to brake dust and road grime.

How to remove a rear wheel?

Park the vehicle on a firm, level surface. Use a tire iron or the appropriate socket to loosen the lug nuts on the first rear wheel, then slide a jack beneath one of the vehicle’s rear designated jack points to lift the vehicle up.

How to unscrew a bearing nut?

Use a ratchet to unscrew the axle bearing nut. Beneath the dust cover, you’ll find the axle bearing nut. This large nut is usually a 22 or 24 millimeter metric socket, or a 7/8” standard socket. Use a breaker bar or half inch drive ratchet to turn the nut counterclockwise in order to remove it.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9