How Do I Change a Golf Shaft?
- Step 1. Scrape off the ferrule at the bottom of the club head's hosel with a utility knife. Place the club into a shaft...
- Step 2. Push on the base of the hosel with a pry bar to release the head from the shaft. Catch the head as it falls off...
- Step 3. Use a utility knife or sandpaper to remove the paint from the tip of the replacement...
Full Answer
Can you change the shaft in a golf club?
Even putter shafts can wear down over time. People often like to change the shaft in their golf club, whether it's because the current one broke or because they want to try out the newest one on the market without purchasing a new club. To help save money, this is a task anyone can do with the right tools.
Does Nailing Your iron shafts make your golf clubs longer?
You hit more iron shots than drives in a typical round—that alone should motivate you to soup-up your sticks. And get this: In some cases, nailing your iron-shaft specs can make you a full club longer, from your wedge on up.
When should I switch from steel to graphite shafts in my Irons?
When should I switch from steel to graphite shafts in my irons? Good question, but a not so simple answer. The usual reasons to switch from steel to graphite are to play a lighter shaft to increase swing speed, or to reduce the amount of vibration from a steel shaft.
How do you fix a broken shaft on a golf club?
Rotate the shaft to the left and right a few times to make sure the epoxy glue covers the entire surface inside the hosel. Remove the club from the shaft clamp and tap the butt end of the grip on the floor to push the shaft all the way into the head.
Can I change the shafts in my irons?
If you're thinking about changing the shafts on your golf clubs, you can either do them yourself or take them to your local golf shop.
How do you change golf shafts?
0:335:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool so we lay it in in this little groove right here. Which is going to slide back and forth andMoreTool so we lay it in in this little groove right here. Which is going to slide back and forth and put pressure and pull on the head. As the shaft is heated. Then we tighten the shaft.
Can you change club shafts?
Scrape off the ferrule at the bottom of the club head's hosel with a utility knife. Place the club into a shaft clamp to hold it in place while you work on the head. Use a heat gun to heat up the area around the hosel to soften the epoxy glue that connects the shaft to the club head.
Can you Reshaft your own golf clubs?
Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.
How do you install iron shafts?
5:117:44SHAFT INSTALL Steel - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce the ferrule is in position take the head and push the ferrule into its final position tap theMoreOnce the ferrule is in position take the head and push the ferrule into its final position tap the butt of the shaft on a hard surface to ensure the shaft is installed to the bottom of the hosel.
How do you remove a golf club shaft?
1:145:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp once you get the ferrule off you're going to need a few minutes here up you can use basically aMoreUp once you get the ferrule off you're going to need a few minutes here up you can use basically a gas gun which I'll use a lot of times if I'm removing a steel shaft.
Can I replace my steel shafts with graphite?
On golf clubs that are not forged, light work will still be included, but you can replace the steel shafts with graphite. You will have to heat the clubhead and remove it, and you may have to buy a new grip. It's a little involved, but completely doable.
What is a golf shaft adapter?
Shaft adapters make it possible to get the best fit between club and shaft and also enable very slight adjustments to the performance of the assembly that can improve your performance - and they can also make it possible to switch heads.
How long does it take to Reshaft a golf club?
How long does it take to reshaft a driver? It takes 24 hours to reshaft a golf driver. The actual time depends on the epoxy used for this process. If you use an epoxy such as the Tour epoxy, you can get done with the reshafting process really fast and your driver will be ready to use in about half an hour.
Do iron shafts make a difference?
It can give you the best chance at striking the center of the face that will result in optimal launch conditions on the course. It absolutely has an effect on how well you can play. The shaft is similar to the transmission of a car. While it's not the engine, it's still extremely important.
Are steel shafts better than graphite?
Typically, steel shafts are much heavier, more durable and are generally less expensive than their graphite counterparts. They are more often than not made from stainless steel and they tend to weigh in between around 90g-120g. Torque or lateral twisting found in all graphite shafts is lower in steel irons.
How do you Reshaft?
Reshafting Golf ClubsStep 1: Secure the Club. Place the shaft in a vise and tighten it, if your shaft is made of steel. ... Step 2: Remove Existing Shaft. ... Step 3: Prepare the New Shafts. ... Step 4: Install the New Shafts. ... Step 5: Adjust as Needed. ... Step 6: Install the Grips.
Instructions
Remove your old shafts. If they are made of steel, place one in a vise, then tighten it. If there is a plastic ferrule where the club head meets the shaft, wrap it in a wet paper towel to keep it from burning. Wearing a pair of fire-retardant gloves, heat the hosel of the club head for 30 seconds with a heat gun, then twist the shaft to remove it.
About The Author
Bill Herrfeldt specializes in finance, sports and the needs of retiring people, and has been published in the national edition of "Erickson Tribune," the "Washington Post" and the "Arizona Republic." He graduated from the University of Louisville.
How to remove ferrules from hosel?
Use the utility knife to cut off the ferrule, which is the small plastic piece by the hosel. A little heat may be necessary if the ferrule is difficult to take off. If so, put the butane torch near it.
Do putter shafts wear down?
By Tami Fisher. Even putter shafts can wear down over time. People often like to change the shaft in their golf club, whether it's because the current one broke or because they want to try out the newest one on the market without purchasing a new club.
TEST SHAFT WEIGHT
HOW WE DID IT: Ten golfers, with handicaps ranging from 2 to 18, took five swings each with 6-irons built to three shaft weights (85, 95 and 105 grams) in two flexes (regular and stiff). Test subjects used the same iron-head model and the same shaft model throughout the test.
WHAT IT MEANS TO YOU
1. Lighter shaft weight doesn’t equal faster speeds. The average swing speed, ball speed and distance numbers are pretty similar, regardless of weight (or flex).
How to fix a club head that is stuck to the shaft?
Step 1. Scrape off the ferrule at the bottom of the club head's hosel with a utility knife. Place the club into a shaft clamp to hold it in place while you work on the head. Use a heat gun to heat up the area around the hosel to soften the epoxy glue that connects the shaft to the club head.
How to remove epoxy from golf club?
Remove the club from the shaft clamp and tap the butt end of the grip on the floor to push the shaft all the way into the head. Wipe down the hosel with a soft cloth to remove any epoxy residue. Let the epoxy dry for several hours before using the golf club.
What is the hosel on a golf club?
The hosel is the junction point between the head and the tip of the shaft. Check the size with a shaft identification gauge if you cannot find it on the label.
Can you replace a golf club shaft yourself?
It's usually best to consider having shaft replacement done by someone who knows what they are doing. Instead of paying the pro shop the next time you need to change a golf club shaft, save money by doing it yourself at home. Make sure your replacement shaft is the same size as the original or it might not fit inside the club head's hosel.
How to put shaft on club head?
Insert the shaft into the club head's hosel. Rotate the shaft while sliding it in and out of the hosel, evenly coating the shaft and hosel with epoxy. Align the shaft graphics the way you want them by rotating the shaft. Then, tap the butt end of the shaft on the floor to seat the tip against the bottom of the hosel bore.
How to remove a steel shaft from a metal?
Steel Shafts: To remove a steel shaft from a metal wood or iron, place the shaft in a super lock tight shaft holder. Tighten the STSL in a vise. If there is a plastic ferrule in place, wrap a wet paper towel around it to prevent burning. While wearing protective leather gloves, aim the flame of a torch at the hosel.
How to remove graphite shaft?
Graphite Shafts: To remove a graphite shaft, place the shaft in a graphite shaft extractor following the instructions that came with the tool. Heat the hosel with a heat gun while wearing leather gloves. Slowly turn the extractor's threaded bolt with a box wrench. If the head does not loosen, reapply heat to the hosel.
How big is a wood shaft tip?
Most iron shafts have a .370 of an inch tip and most wood shafts have a .335 of an inch tip. Follow the tip trimming instructions to trim the tip end of your new shaft so it matches the size of the shaft you extract. After the tip has been trimmed, abrade or roughen the shaft tip.
Why do golf clubs have stiff shafts?
For those who swing the club powerfully and with speed, they need more control over the club. That is why they tend to choose stiff shafts. Those who have a less powerful swing need to choose regular shafts to flex the hit. Heavy shafts or stiff shafts can sometimes make it difficult to gain speed.
Why reshaft irons?
Reasons for Reshafting Irons. You may think that reshafting is expensive. But, there are certain situations where it is better to get the irons reshafted than buying new ones. The golf club is new, but the shaft is not working well for your playing style. Your swing has changed drastically and is now negatively effecting your game.
What is the part above the clubhead called?
Important things to consider before reshafting an iron. The part right above the clubhead is called hosel. After the hosel , there is ferrule that holds the hosel and shaft together. Check the shaft tip and make sure to measure everything properly. Installing steel and graphite shafts tend to have a different process.
What is the difference between a stiff shaft and a regular shaft?
This depends on the swing speed and power of the player. Stiff shafts are for those who swing with more speed. Regular shafts are better for golfers who swing with less speed.
Why are steel shafts so heavy?
Steel shafts are heavier and can be a problem for those who have hand and shoulder issues, especially among older players and women, as they tend to have less speed. That is why it can be quite effective for them to shift to graphite shafts.
How much does it cost to reshaft a golf club?
Reshafting a golf club will cost you $50 to $250. This price depends on the type of shaft you choose, the labor charges, and the other fees charged by the repair company.
Should a golf club be fitted to a person's swing?
Every person has their own way of playing, and the golf club should be fitted to each person’s playing style. In case the swing is not performing well or the ball is getting hit the wrong way, it is time to think of getting the shaft replaced.