There is an easy method to check the electric motor on any EZ-Go golf cart. Go to the back of the golf cart and find the panel that covers the electric motor. Four or six screws will hold the panel in place. Use the screwdriver to remove all the screws, turning them counterclockwise and putting them in a secure location after removal.
Full Answer
How to check the electric motor on an EZ-GO golf cart?
There is an easy method to check the electric motor on any EZ-Go golf cart. Go to the back of the golf cart and find the panel that covers the electric motor. Four or six screws will hold the panel in place. Use the screwdriver to remove all the screws, turning them counterclockwise and putting them in a secure location after removal.
How does an EZ Go Starter work?
E-Z-Go gas cart Starter/Generator and Voltage Regulator When the solenoid is energized through the logic switches (Key Switch and Accelerator Switch), current flows from B+ through the solenoid, to F2 of the Starter/Generator, though the field winding to F1, through the strap, to A2, through the armature to A1 to ground.
Where is the solenoid on an EZGO golf cart?
If you want to check if the solenoid’s working or replace it, it is crucial to know exactly where it is located. The solenoid is located inside the controller box connected to it. And the controller box is placed under the seat of the EZGO golf cart. Lift the seat and remove the covering.
Why is my EZGO RXV cart not working?
If one is driving an EZGO RXV and the cart is not working anymore, there can be several underlying reasons. But a bad solenoid can be the most common one. Always check the battery voltage and the clicking sound while pressing on the pedal. First, check the connections and wires of the main circuit.
How do you test a golf cart starter motor?
0:011:03How to Check the Generator on Your Golf Cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you should see the voltage jump up from around 12 volts with the cart running to about 16 voltsMoreAnd you should see the voltage jump up from around 12 volts with the cart running to about 16 volts that that happens that proves the generator is fine you simply need to change.
How do I test my EZ GO starter?
Touch the other end to the F2 stud on the starter generator. As soon as the positive cable touches the F2 stud, the motor should start to spin in a counter clockwise rotation. If the motor spins, then it is working correctly. If the motor fails to spin, then it is defective and needs to be replaced.
Where is the reset button on a ezgo golf cart motor?
Locate the motor Remove the panel so the electric motor is visible. Electric motors usually include reset buttons that can perform similar to circuit breakers. Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.
How do I know if my electric golf cart motor is bad?
You have enough going on in your life without your golf car refusing to start when you turn the key in the ignition. If your golf car won't start, is slower than it used to be, or is experiencing other technical problems, you could have a bad motor on your hands.
How do you test a ignition switch on a golf cart?
Testing a Club Car Ignition SwitchFind the back and red wires on the back of your battery pack.Connect the black wire to the negative terminal and the red to the positive.Keep the cart turned off while you work on it.Check the wires with a probe meter while the cart is off – only one wire should have a charge.More items...
How does EzGo starter generator work?
The starter generator works in two ways; the starter portion cranks the engine and the generator portion recharges the battery. When the gas pedal is depressed the starter cranks the engine over. When it begins to run on its own, the generator portion of the unit begins to charge the 12-volt battery.
Does a ezgo golf cart have a reset button?
Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button. Push the button to reset the motor.
Why won't My EZGO start?
Check Ignition Wire If it has, reseat the wire into the solenoid. If the wire appears corroded, wear your work gloves and wipe down the wire and attempt restarting the golf cart. If the cart will not start, then you will need to replace the ignition wire.
Do all golf cart motors have a reset button?
Electric golf cart motors have a reset button on their chassis which is designed to put your motor back into its original factory state. While it doesn't repair damage that may have occurred to the motor over the years, obviously, it does help to overturn any changes to the operation which may have occurred.
What are the symptoms of a bad solenoid in a golf cart?
On an electric golf cart, the most common symptom is the solenoid is not delivering electricity to the controller when the vehicle's ignition is turned on. In normal operating conditions, the solenoid clicks on and off with the ignition switch. A failing solenoid will generally not click.
What would cause a golf cart not to start?
As the main source of power to your electric golf cart, the batteries are commonly the cause for why your electric golf cart won't start. Acid-based batteries are typically used for electric golf carts and must be recharged in order to work properly.
Why does my electric golf cart have no power?
If you're lucky, the problem could be as simple as a loose wire or a broken coil. In some cases, corrosion can also be a factor. If you suspect a faulty solenoid, your best bet is to take your cart to a repair shop. A mechanic can diagnose the problem and replace the solenoid if necessary.
How to check if electric golf cart is running?
It sounds absurd, but if your electric golf cart is not running, the very first thing I would check is the reset button on the side of the motor, if your cart is so equipped. Check around the outside of the motor and see if you can find a small button to press. This is usually a safeguard against overheating.
What is wrong with my electric golf cart?
Electric golf carts are usually trouble-free and do their job efficiently and with no fuss, but sometimes you suspect your golf cart is experiencing a problem. If the speed seems to be off, or your cart gives off a burning wire smell, your golf cart motor might have a problem. Using a multimeter, a jumper wire, and a 12-24 volt power source, ...
Why is it important to test a motor before replacing a controller?
This is an important test to do on your motor before replacing the controller because a short could damage the new controller irreparably. Please note that this test will not find a short in the armature. Note that continuity testing is not directional, so it doesn’t matter if the red and black are reversed.
When did golf carts start having separate excited motors?
In 1999, some golf cart manufacturers started offering Separately Excited Motors. Sepex (Regenerative) Motor carts have a toggle switch F&R device as opposed to the lever-action. In addition to this identifier, they have a tow/run or tow/maintenance switch which cuts power to the controller. Most of the modern-day carts are equipped ...
What is a golf cart?
Golf carts are also known as golf cars. The term "cart", in its purest sense, refers to a vehicle that does not travel under its own power. Golf cars, however, are most commonly referred to as golf... link to Club Car DS Wiring Diagrams 1981 To 2002.
What is a series motor?
A series motor has field and armature windings that have the power fed to them from the same source, either in series or parallel. A SePex motor, as the name indicates, is a motor that has a separately excited field and armature windings. These two motor functions are sent to the PDS or DCS giving greater control over the motor.
How many volts should a starter generator output?
It should peak at about 15 volts (the maximum output of the Starter/Generator’s charge ability). If it does increase, then the Starter/Generator is alright. If it doesn’t, there is a problem with the Starter/Generator.
What happens when a starter generator spins?
That completes the circuit, so the Starter/Generator begins to spin. As it spins, a voltage appears at the DF terminal of the Starter/Generator, which is connected to the Voltage Regulator.
How many volts should a jumper have before it is shorted?
Before the jumper is shorted to ground, the voltage at B+ should, of course, reflect the charge state of the battery (around 12 volts), but when the jumper is touched to ground (which is what the Voltage Regulator does in instantaneous bursts), the voltage at B+ should rise as the motor’s speed is increased.
Do E-Z-Go Golf Carts have titles?
E-Z-Go Golf Carts, unlike vehicles, do not have a title, but they do have serial numbers. If you are buying a golf cart, it is essential to check the serial number to ensure you do not buy a stolen one. Each E-Z-Go Golf cart has a unique serial number that you can use to identify your golf cart.
Where is the E-Z-Go Cart Serial Number
As mentioned above, all E-Z-Go Golf carts have unique serial numbers. These numbers are essential when buying replacement parts for your golf cart. Textron Specialized Vehicles has been building golf carts for a long time, and the serial numbers are placed on different parts of the golf carts.
How do I push my E-Z-Go Golf Cart?
It can be frustrating when your battery is flat and your golf cart will not roll. To push it to the nearest charging or gas station, you need to release the motor brake. Follow these easy steps to do that.
Why does my E-Z-Go golf cart not move
There are several reasons why your cart refuses to move, but you should check the battery before anything else. If the battery is charged, here are some other reasons why your golf cart will not move.
Are all E-Z-Go Golf carts electric?
No, there are both electric and gas-powered E-Z-Go Golf carts available. Bear in mind that there are several models you can drive on the street, but those are all-electric. These electric models run on batteries that you have to charge at least every 24 hours, depending on how much you use them.
How to tell the Assembly year of my E-Z-Go golf cart
The placement of serial numbers is discussed above, and you will find the manufacturer’s number right next to it. The manufacturer’s number consists of one letter and 3 or 4 numbers. The last two numbers indicate the last two digits of the year of assembly.
How to service E-Z-Go Golf Cart
Like all vehicles, E-Z-Go golf carts require regular maintenance to enhance longevity and performance. You should ensure that your golf cart is serviced after every six months of use. That will ensure that you spot problems and repair them early, which will help reduce repair costs. Here are essential guidelines for E-Z-Go golf cart maintenance.
Why is my Ezgo golf cart not clicking?
A EZGO golf cart that is not making a clicking sound can be due to a failed solenoid. If there is no sound in the cart while igniting the switch, then the problem can be the cart’s control circuitry. This means the solenoid has stopped working. Then it is required to replace the solenoid.
How to test gold cart solenoid?
You can test the solenoid by simply disconnecting the main circuit high wires and by using a multimeter.
Why is my cart solenoid getting hot?
If the cart solenoid is getting hot, then the problem can be with the solenoid or the circuit wiring. It is better to check the solenoid thoroughly. Use proper solenoid, which matches the amperage and voltage of the cart system. Use high-quality solenoid to avoid the heating problem.
What to do if solenoid is not working?
If the solenoid is not working after checking and testing the solenoid using a voltmeter, then it is time to replace the solenoid all together. Always be sure of the model and year of the cart. Check online to get all specifications. Compare the online picture of the new solenoid with the older one.
What happens if a cart starts with a solenoid?
If the cart starts, then the solenoid is the problem and, if it does not, then the problem is not solenoid but something else. A cart owner should remember that bypassing the solenoid can damage the ignition system and central circuit of the cart. Also, bypassing should only be used for checking the solenoid and not permanently.
What should the voltmeter reading be?
The voltmeter readings should be 0 ohms. Now, switch on the key and put the direction is forward, and step on the accelerator. After the click sound, put the probe on large terminals and check the readings. The voltmeter readings should be around 0-0.4 ohms and not more than that.
Where is the solenoid located on a golf cart?
The solenoid is located inside the controller box connected to it.
