Golf-FAQ.com

how to check lie of a golf club without a lie machine

by Paolo Stroman Published 3 years ago Updated 2 years ago
image

The following procedure is the easiest and most accurate way to check your lie angle. First, you will need a water-based pen (oil-based will not work) and a shot marker such as the following Draw a straight line on the golf ball with a water-based pen as shown below.

Part of a video titled HOW TO CHECK LIE ANGLES ANYWHERE - YouTube
9:00
11:13
Maybe putting a piece of tape on it need be putting the line on the wiffle ball. And going throughMoreMaybe putting a piece of tape on it need be putting the line on the wiffle ball. And going through the process you will get the exact same. Results.

Full Answer

What is a lie angle on a golf club?

The lie angle of a club is the angle of the shaft in relation to the ground when the sole of the club lies flat on the ground. Lie angle will either be tow up, tow down or neutral. What is a Loft and Lie Machine?

What is the loft and lie of a golf club?

This is referred to as the loft. The lie angle of a club is the angle of the shaft in relation to the ground when the sole of the club lies flat on the ground. Lie angle will either be tow up, tow down or neutral. What is a Loft and Lie Machine? In simple terms, it is a device used to adjust the loft and lie of a club.

How to use a golf lie board?

Ditch the lie board. The dynamic lie test simple and allows you to hit balls from the grass. Draw a heavy line on one side of the golf ball with sharpie and place it perfectly vertical facing the club head. After impact, the line should be transferred onto the club face.

What is the golfworks loft and Lie Machine?

The Golf Club and Economy Loft and Lie Machine are precision-made and capable of bending and adjusting left and right-handed clubs. Woods, irons, and putters are accurately altered to the specification required for loft and lie angle. Each machine is independently manufactured in The GolfWorks machine shop and comes with an engraved serial number.

image

How do you know if a golf club is lying?

Draw a straight line on the back of the golf ball, and have it facing the clubhead. After you make impact the line will appear on the face. If it's pointing towards the toe, then your club is too upright. If it's pointing towards the heel, then it's too flat.

How do you measure the lie angle of a golf iron?

Lie: The angle between the shaft and the ground line when the club is measured in normal playing position with the center of the sole touching the ground line.

How do I find my lie angle?

1:268:02What's my Lie Angle? Dynamic Lie Test - YouTubeYouTubeStart of suggested clipEnd of suggested clipUh if the line is it is going to transfer to the club if the line is straight that means that myMoreUh if the line is it is going to transfer to the club if the line is straight that means that my strike is ideal. So the lies like this is um is ideal. But if the line uh points to the toe.

How do you measure golf clubs loft and lie?

0:166:36Golf clubs: Loft, lie, and why they matter??? [Beginner's guide]YouTubeStart of suggested clipEnd of suggested clipAnd go the shortest distance. So as we go from the longest club in my bag the driver to the shortestMoreAnd go the shortest distance. So as we go from the longest club in my bag the driver to the shortest. This wedge the lofts progressively. Increase and the ball will go higher in the air.

Does 1 degree upright make a difference?

Yes it will make a difference, I play 2 degree upright and +1/2. If your hitting the ball left all the while (I am guessing your right handed) won't be to do with having the lye angle to flat.

What happens if club lie angle is too upright?

The lie angle is known as 'too upright' when the toe of the club is lifted too high above the ground. This will cause the heel to strike the turf first, shutting the club-face and sending the ball to the left.

Can the lie angle of a golf club be changed?

Using a club bending machine to change the angle on a golf club is among the fastest ways to improve a player's ball flight. Whether it's changing the lie to improve accuracy or changing loft to make sure that the player's clubs are progressively consistent, angle bending is a major factor in club performance.

Does changing loft change lie angle?

As you change the loft and the face angle, you will also change the lie unless there is a separate setting to alter the lie independently of loft.

How much does it cost to change the lie angle of a golf club?

$3 to $5 per clubThey normally charge $3 to $5 per club to make adjustments, so this could save you some cash if you can get them to throw it in.

How much does 1 degree of loft affect distance?

How Much Does 1 Degree of Loft Affect Distance? Given that you're at your maximum clubhead speed, just 1-degree change in the loft angle of a golf driver can affect your driving distance by 2-4 yards.

What is the difference between loft and lie angle?

Loft is the primary factor in how high or low a golf shot flies. The more loft a club has, the higher the resulting shot. Wedges have the highest loft in a set of irons. The "lie angle" of any clubhead is the angle between the center of the shaft and the sole.

What happens if my lie angle is too flat?

If your lie angle is too flat, typically meaning it's closer to 0 degrees than 90 degrees, then that means you will typically hit the ground with your club with the toe side of the sole.

What happens if the ink line is tilted out?

If the line is tilted out towards the toe of the club, your club is too upright and you will need to flatten the lie angle to get the line vertical. If the ink line is tilted towards the heel your club is too flat and you would bend the club more upright.

Can you use impact tape on a lie board?

This will give you the ability to bend your clubs to adjust your lie angle. Using impact tape and hitting down on a lie board does not accurately represent what will happen on the golf course. It makes no sense to fit your clubs based off a surface you will never encounter. Ditch the lie board.

Do irons bend during practice?

It is not uncommon overtime that your irons will bend during practice without your knowledge. Frequently check your lie and loft angle with the dynamic lie test especially if you like to practice off of mats. Give your higher lofted clubs special attention and make sure they are exact.

Why do you need to check the loft and lie?

Why Do You Need to Check Loft and Lie? The ultimate goal is to have the sole of your golf club perfectly parallel to the ground at impact. This means you have the right lie angle. If the toe of the club is too “in the air” at impact, it means the lie angle is too “upright” and you need the lie to be bent “flatter.”.

Why do you bend the lie more upright?

If the heel is too in the air, then you guessed it, you need to bend the lie more upright because the lie angle is too flat. It’s worth noting that’s important to understand how the sole of the club is at impact, not at address. How the club is sitting at address really doesn’t physically mean anything. Theoretically, an incorrect lie angle could ...

What is loft in golf?

Loft is the angle of the club face which influences the trajectory of the golf ball. In short, loft plays a huge part in controlling how far you hit each club. Lower lofts will go further and higher lofts will go shorter. Lie angle is pretty simple as well, but I’ll help clarify it. Think of the shaft of the the golf club and ...

How often should I check my loft?

It’s possible your loft has changed. At the very least, you should check your loft and lie at least once a season. I’d recommend players with forged irons do it a minimum of two times (once at the start and end of the season). If you’re serious player, I’d check maybe a little more – especially if it gives you mental peace.

Is each club manufacturer's standard?

That’s not true. Each club manufacturer builds their club to their own “standard” and it can vary from brand to brand. Admittedly they will be close, but it’s important to be aware that they can differ. Most importantly, you should work with a good fitter to make sure you know the correct lofts and lies for your swing.

Below is a list of the Best Loft and Lie Machine Manufacturers, in random order

The company started in 1988 and has revolutionized custom club fitting and making. Accuracy is the key to any bending operation and the company has developed machines that can bend forged and cast irons, hybrids, putters, and metal woods.

Final Thoughts

Hopefully, a few basic facts about adjusting Loft and Lie Angle will be clearer to the average golfer after reading this article. For the DIY enthusiast, it is imperative to understand how and what result is required, before venturing into the garage to do the adjustments.

Conclusion

Bending a golf club’s lie angle at home certainly steps up your golf club tinkering skills. Regripping or changing the length of a club is a bit easier than this project. However, with the proper lie and loft machine, you should have no trouble completing the project.

pmcuk

Has anybody made a DIY vice for holding an iron club head so you can adjust the lie yourself?

Pigems

It's only $3/$5 to have a club bent, much cheaper then buying a machine

Nessism

I think you could replicate Ping's bending method fairly easily if you have a heavy duty bench vice and some homemade hosel clamps. You will have to fab up something to bend loft too, but lie can be done with a rubber mallet. Of course you need a spec gauge after bending.

pmcuk

I should have said right at the start that I have an inclinometer and magnetic spirit level for measuring lie - it's perfectly good and I don't need anything more elaborate, so I don't need a loft-lie machine for the measurement at all. Thanks Nessism - that's a really useful DIY club holder for lie adjustment.

Nessism

Not wooden blocks. They are metal, aluminum I presume. You should be able to get a block of aluminum and drill/ream it for the proper hosel size. Then saw the block right down the middle of the bored hole. Sandwich the hosel with your blocks and clamp it tight in a sturdy bench vice for adjustment.

curran22

Personally I prefer my Mitchell steelclub as I do not have the ingenuity as Nessism. Those are some pretty slick tools. Hats off bro!

High Plains Driver

I had a Mitchell Steelclub+ for years, and it was awesome. However, I rarely have the need to alter loft of lie now, other than the occasional wedge, so I use this:

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9