- Access the Micro Switch. Most of the micro switches on EZGO golf carts including the EZGO TXT, EZGO RXV, and EZGO Express are located beneath the cart ...
- Connect a Voltmeter. The micro switch will have two wires connected to it. ...
- Check for Continuity. With the switch in its original position and in the alternate position, check the readings in the voltmeter from the micro switch.
- Reset the Switch. Once the continuity test is completed, remove the voltmeter and connect the two wires back to the micro switch.
What does the micro switch do on a gas golf cart?
When the micro switch is activated, with the key ON or OFF in a gas golf cart, it allows battery reference voltage to flow to the key switch in many cases. But, it stops there, until key switch is turned ON to allow the power to activate the solenoid.
How do you test an accelerator micro switch on a golf cart?
A typical accelerator micro switch on a gas golf cart only has two terminals as well, a common and either a normally closed (NC) or normally open (NO) depending on the year and model. However, our test is generic and applicable to most carts. Again, leave your black probe on the battery negative terminal and use your red probe for testing.
How does a gas golf cart start?
In gas golf carts, a micro switch located on the accelerator pedal triggers a signal that will start the cart’s engine. The cart will run without any problem as long as this micro switch remains active.
Where is the ignition wire on a golf cart starter?
Locate the ignition wire on your golf cart. This wire goes from the golf cart key switch assembly to your cart's starter. Visually inspect the solenoid area of the starter, where the key switch wire plugs into the cart. On some cart models, this end of the key switch wire can become dislodged during use on rough terrain.
How do you test a micro switch on a gas golf cart?
Again, leave your black probe on the battery negative terminal and use your red probe for testing. With the key switch ON, you should read battery voltage at the common terminal (C or COM), but not the other terminal. Once the micro switch is activated, you should read voltage on both terminals.
How do I test my EZ GO micro switch?
Depress the pedal slowly. The reading should be 0.45 - 0.53 volts just as the micro-switch is activated. Depress the pedal slowly to full throttle. The reading should move smoothly to about 1.5 volts.
How do you test a club car DS micro switch?
Micro Switch Testing The micro switches are simple 2 wire on/off switches. They open and close mechanically. You can test function with a voltmeter if you first verify 36v in on the supply side of the switch, then mechanically trigger the switch, and test for 36v on the output side.
What does the micro switch do on a golf cart?
Microswitches are used in many golf cart applications. They are used at the accelerator pedal to provide a signal to the solenoid that you have depressed the pedal and are ready to go. In an electric golf cart, the solenoid sends power to the controller to move the cart.
How do you test if a micro switch is working?
2:134:10Electric shower problems: How to test a microswitch. - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis is the normal micro switch and normally. The power comes in the top connection. Here and whenMoreThis is the normal micro switch and normally. The power comes in the top connection. Here and when the buttons pressed it goes out here and off to the elements or whatever.
How do I test a switch with a multimeter?
0:110:52How to check a faulty switch using a multimeter - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst set up and calibrate the multimeter as per the instructions. And turn the dial to the lowestMoreFirst set up and calibrate the multimeter as per the instructions. And turn the dial to the lowest ohm rating a switch needs to be activated in order to check its continuity.
How do you bypass a micro switch on a golf cart?
You can bypass the reed switch in an EZGO golf cart by connecting the red wire of the reed switch to the white wire from the charger receptacles and to the red wire from the FRN micro switch.
How do you test a golf cart switch?
Testing a Club Car Ignition SwitchFind the back and red wires on the back of your battery pack.Connect the black wire to the negative terminal and the red to the positive.Keep the cart turned off while you work on it.Check the wires with a probe meter while the cart is off – only one wire should have a charge.More items...
How do you test a club car on a DS motor?
13:1937:53Club Car 48 Volt Powerdrive Testing 1995-2013 - YouTubeYouTubeStart of suggested clipEnd of suggested clipPosition place the red positive probe on the speed controller M minus terminal place the blackMorePosition place the red positive probe on the speed controller M minus terminal place the black negative probe on the s2 motor terminal your vom should display continuity.
Where is the micro switch located on a golf cart?
In a golf cart, you're going to find a large number of these switches throughout its build. For example, there is a micro switch located on the accelerator pedal. This switch activates when you push the pedal and sends a signal to the solenoid.
Why won't my gas golf cart shut off?
Troubleshooting. Switch the car to neutral before turning the key off. The problem with shut down may have occurred from the kill circuit, which is controlled by the top microswitch. You may have to replace the microswitches or solve the problem by tightening up the circuit.
Where is the micro switch on club car golf cart?
2:1211:27Replacing Mircoswitches on Club Car DS - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis air intake hose because that's in the way of the cover we have to remove it we have to take outMoreThis air intake hose because that's in the way of the cover we have to remove it we have to take out this screw it's got a 5/16 head and then yeah just push on this upper corners of this box. Top and
What is a microswitch?
As the name implies, a microswitch is a small switch. Microswitches are used in many golf cart applications. They are used at the accelerator pedal to provide a signal to the solenoid that you have depressed the pedal and are ready to go. In an electric golf cart, the solenoid sends power to the controller to move the cart.
What is a golf solenoid?
In an electric golf cart, the solenoid sends power to the controller to move the cart. In a gas golf cart, the solenoid sends power to the starter/generator to start spinning the engine. Microswitches also serve a purpose as part of the forward and reverse direction selector switch on many golf carts. In this application, they can be used ...
How to get a golf cart going without a glitch?
To get your golf cart going without a glitch, you most definitely need the solenoid of your cart to be functioning properly. Thus, it goes without saying that you must check this component occasionally to monitor its performance so that you don’t get stranded mid-way.
What does the inductive throttle sensor do on a golf cart?
When you push down the pedal of the golf cart downwards, the inductive throttle sensor sends out the first low power signal to activate the solenoid on its low side and the speed controller. The low side is the steel rod of the solenoid.
What is a solenoid wiring diagram?
A solenoid wiring diagram can be very helpful in guiding you about the various connections made to and from the solenoid. This can come in handy when you set out to troubleshoot a problem in your cart on your own. The solenoid wiring diagram is generally very simple, straightforward and self-explanatory.
What is a solenoid in a golf cart?
A golf cart solenoid is one of the major components of any golf cart. This part is essential regardless whether you own an electric or gas golf cart because both types primarily rely on a solenoid for their movement. What this means is whichever brand or model you choose for your cart, a solenoid is truly an indispensable part of the vehicle.
Why is my golf cart not clicking?
This may be because the safety reed switch is not working properly in the charger socket. There could be a loose connection of the MOLEX plug.
What does it mean when your car doesn't start?
If the cart does not start, then it is a clear sign that your solenoid does not have a problem. However, if it does, this does not indicate that the solenoid is the cause of the problem. You will have to check out the complete ignition system.
Why does my gas cart not turn over?
In a gas cart, a bad solenoid prevents the starter from being engaged and therefore results in the engine not turning over.
What direction does a golf cart transmission selector go?
Confirm that your golf cart transmission selector switch is set fully to the forward, reverse or park direction , depending on your model of golf cart. If the switch is partially set in between modes, it can result in your cart failing to start correctly.
Why replace the key wire on a golf cart?
Replace the golf cart key switch wire if the connector to the key switch or solenoid is significantly frayed or corroded. Over time, corrosion will build up on the ends of the wire due to exposure to damp weather. Significant corrosion build-up can prevent your cart from starting consistently and ultimately result in the cart failing to start.
