
Check the wires with a probe meter while the cart is off – only one wire should have a charge Turn the key on and check the wires – the second wire should now have some charge Just like with an EZGO cart, a lack of charge in the secondary wire – or either wire when you turn on the ignition switch – indicates a problem.
- Find the back and red wires on the back of your battery pack.
- Connect the black wire to the negative terminal and the red to the positive.
- Keep the cart turned off while you work on it.
- Check the wires with a probe meter while the cart is off – only one wire should have a charge.
How to replace the ignition switch on club car golf cart?
Remove the face nuts with a pair of pliers. Now, the ignition switch can be removed easily. Install the new switch on to the plate and screw the face. Reverse the steps given above for locking the ignition switch back in place. Turn on the switch and verify that it is working. How to Replace the Ignition Switch on Club Car Golf Cart
How do you test the coil on a golf cart?
Testing the coil on a golf cart is required due to a bad ignition coil or a problem that may run deep in the engine. Coils are intrinsic to every golf cart and the ignition system powers the spark plugs. Locate the ignition coil in the golf cart by getting the seat of the golf cart raised to, as would be mentioned in the owner’s manual.
What is a tow run switch on a golf cart?
Tow run switches are utilized in golf carts that have a motor that is stimulated separately from the controller and vice versa. The vehicle should be fully charged before it is left unattended for an extended length of time without being visited or charged. Once the vehicle is fully charged, the switch should be set to “TOW.”
How do I know if my golf cart is going bad?
The first and most obvious symptom is the golf cart won’t start. If it is a gas-powered cart, the engine doesn’t turn over, and if it is an electric cart, the cart doesn’t move. Now, on to the next symptoms…

How do you check a key switch?
3:068:07How to Test a Riding Lawnmower Key Switch - YouTubeYouTubeStart of suggested clipEnd of suggested clipStarting position and then we're gonna go ahead and turn the key switch into the spring-loadedMoreStarting position and then we're gonna go ahead and turn the key switch into the spring-loaded starter position and you should hear a beep. Hear that so the starter circuit on.
How do you jump an ignition switch?
It's pretty easy to jumpstart your vehicle. All you have to do is connect to identify the ignition coil and the battery. Connect the positive terminal of the battery to the positive side of the ignition coil. Also, identify the starter solenoid and connect it to the positive terminal of the battery.
How do you bypass the ignition switch on a golf cart?
This process includes these steps:Turn off the ignition switch to minimize your risk of electrocution. ... Locate the wires for your cart's ignition switch. ... Use wire snips to cut these wires away from their connectors. ... Touch the engines together carefully to bypass the ignition switch and send power to your engine.More items...
How do you check ignition switch terminals?
Locate and identify the pins on the back of the ignition switch, There should be four terminals marked "BATT" for Battery, "ST" for Start, "IGN" for Ignition, and "ACC" for Accessory.
Can you bypass ignition switch?
Bypassing a broken ignition switch is quite a technical procedure that will require a little more than just a manual and a keen sense of learning. The best case scenario is that you take your car to a professional to handle it or simply just replace the switch.
How do I tell if my ignition switch is bad?
Symptoms of a Bad Ignition SwitchEngine Won't Start. ... Vehicle Starts and Suddenly Stalls. ... Intermittent Loss of Lighting and Other Accessories. ... Silent Starter Motor. ... Difficulty Turning the Key. ... Lock/Off. ... Accessory. ... Run.More items...•
How to check if key switch is working?
If you wish to check if the key switch is functioning properly, follow these steps. There are two probe wires present in the battery pack – a black and a red. Connect the black probe wire to the 36v negative terminal of the battery pack. The red probe wire should be connected to the back of the battery pack.
What is the difference between blue and red wires on a cart?
The basic rule is that the blue wire generally is connected to the solenoid while the other red wire will be connected to a fuse. From the fuse, the wire will be further extended to another terminal of the solenoid.
Do all golf cart keys have the same key?
Yes, all club car golf cart keys are the same. The downside of owning a golf cart is that the key switch can be easily accessed using any key from the same manufacturer. If you have a single key from a particular manufacturer, you can easily use it to open all the carts made by them.
Is the Ezygo golf cart the same as the golf cart?
Yes, all EZYGO golf cart keys are the same. A key from one golf cart can be used on another EZYGO golf cart. All golf cart keys are dependent on the manufacturer. Each manufacturer will have the same key molds for the keys. Yes, the keys are universal and limited to the manufacturing company.
Can you park a golf cart on a golf course?
Some people park their carts on the golf course but do not prefer other people using it. To avoid this problem, you can change the key switch or use a combination of other techniques. This way the cart cannot be used by others without your permission.
Can you replace an ignition switch on an Ezygo?
If you have identified an issue with the ignition switch on your EZYGO, you may need to replace it with a new one. It is really an easy task to replace the switch with a brand-new one. The first step would be to get the right switch for replacement.
Can you replace a switch with a new one?
It is not too difficult to replace the existing switch with a new one. It can be easily installed without much hassle. This way the access to your cart can be restricted. In general, most people don’t bother about the key as it is not used for any other purpose other than unlocking the cart.
How to check ignition switch voltage?
You can check the voltage of the switch by using two tools – a 12-volt test light or a digital multimeter.
How to stop a car from cranking if you turn the ignition key?
Doing so will stop the engine from cranking despite turning the ignition key to the run position. Step 2: Rotate the ignition key and place it to the run position . Probe the red wire connection to test the voltage. Do the same at the ignition coil’s battery terminal. Step 3: Then, rotate the switch to the start position and probe ...
What does it mean when a switch fails?
It happens when the switch fails in the ‘ON’ position. It may supply power to the fuel and ignition systems when the engine is cranking but stops functioning immediately after.
Why does my car not start after I start it?
A dysfunctional ignition switch can cause plenty of troubles. It may result in some electrical components stop working, the car does not start or dies immediately after being started. You may need to replace the switch if the problem becomes severe or the car does not respond at all.
Why do you need to test a golf cart coil?
Testing the coil on a golf cart is required due to a bad ignition coil or a problem that may run deep in the engine. Coils are intrinsic to every golf cart and the ignition system powers the spark plugs.
Why is my golf cart not starting?
Golf Cart not starting in one go: If you experience that the Golf Cart is not starting in one or two goes, then it is an indication that there may be a failure in ignition coil.
What is the most important thing about a golf cart?
Engine performance issue remains one of the most important concerns. The ignition coils are one of the most important components of an engine of a golf cart. Such issue can compromise the spark which can downgrade the performance of the golf cart.
Why does my golf cart ignition go bad?
The main cause of golf cart ignition coils going bad is the wearing out due to a bad spark plug ignition cable. When a bad plug is inserted, it will have a much higher resistance value. During such high resistance a high amount of voltage gets generated from the secondary wiring of the ignition coil. The excess amount of voltage ends up creating ...
Why does my ignition coil mat fail?
The ignition coil mat fail due to voltage supply being cut down or overload of the ignition control unit. It can also be due to any sort of mechanical damage to the ignition wires due to a faulty valve cover gasket or oil leakages.
How to keep water out of coil plug?
Put grease on the coil plug as it will keep water out of the reach of the connection. Get the coil slide so that the boot clicks into the spark plug. Get the electrical connection reattached. Move to the next unit till the other coils are replaced.
What is the purpose of an ignition coil?
One of the major objectives of an ignition coil is to let a high voltage be induced from a low voltage. There is a laminated iron core which has the task of getting the magnetic field amplified. The primary wiring is connected to the secondary wiring via a connection to the terminal.
How to test golf cart solenoid?
A diode allows current to run in one direction, but not in the other. Testing the diode is a simple procedure. Remove the diode from the circuit and check the leads with a continuity tester.
How to tell if a golf cart won't start?
The first and most obvious symptom is the golf cart won’t start. If it is a gas-powered cart, the engine doesn’t turn over, and if it is an electric cart, the cart doesn’t move. Now, on to the next symptoms…. The engine on the gas-powered cart starts, but the starter doesn’t disengage after starting.
Why doesn't my golf cart solenoid click?
This can be a faulty wire connection, but can also mean the solenoid is beginning to fail. The golf cart solenoid doesn’t click when the accelerator is pressed. This again can be faulty wiring or a failed solenoid.
How to check if a battery is low?
First, follow these steps: Step 1 – Check the battery voltage from the positive connection to the battery negative. A solenoid uses 12-18volts and low voltage will not activate the solenoid. Step 2 – If the voltage is low, check the cable ends for corrosion. Clean and charge the battery.
How to tell if solenoid is bad on golf cart?
The common symptom of a bad solenoid is no clicks when the cart’s ignition is on and you press the accelerator.
Where are the solenoids on a golf cart?
In all golf carts, new and old, the solenoids can be found under the seat or in the engine well and are easily identifiable by the wires that lead to them. Banks of heavy duty solenoids, as in the previous illustration, are mounted on the side or back panel near the electric motor.
What to do if your solenoid is not zero?
If the reading is not zero, then the solenoid is stuck and needs to be replaced. If the ohmmeter does read zero, set the cart to forward travel and turn the key switch on. Press the accelerator pedal (or have a friend do it) and you should hear a click. If you don’t hear a click, measure the resistance anyway.
What is a golf cart go switch?
On your golf cart, this high powered circuit is either your ignition on a gas golf cart or your electrical motor power circuit for an electric golf cart. Basically it’s your golf cart’s go switch, and it’s absolutely essential to your golf cart’s ability to do its job. Golf cart solenoids are also typically one of the first components ...
What is the most important part of a golf cart?
One of the most important components of your golf cart is the solenoid. It is one of the main components of your golf cart that allows it to move. Whether you have a Yamaha, E-Z-GO, or Club Car golf cart, and no matter if it is an electric or gas golf cart, you need a properly operating solenoid to get anywhere. Contents [ show]
Why does my golf cart have no solenoid?
Golf cart solenoids are also typically one of the first components to fail in your golf cart, because they work very hard, turning on and off every time you stop and go in your golf cart. If you have an issue with no start or no go then your solenoid should be pretty high on your list of things to check.
What happens if a solenoid reads infinity?
If it reads infinity or open lead, then the solenoid has an internal fault and requires replacement. Your solenoid should also have a range that it operates in, and if the resistance reads outside of that range, you should replace the solenoid even if it works to avoid damaging other components.
What is a solenoid on a golf cart?
A solenoid, for our purposes, is a type of relay. A relay is a type of switch that uses a low power circuit to operate a high power circuit. A solenoid uses a magnetic coil (the actual solenoid) on a low power circuit to push a rod that closes a high power circuit. On your golf cart, this high powered circuit is either your ignition on ...
What to do if your solenoid doesn't work?
Before you run out and get a solenoid, you’ll have to test the entire ignition system this way to find out what’s not working, and it is a bit of a pain.
What is a micro switch on a gas pedal?
This switch is what sends the low power to the solenoid. The solenoid uses this to create a circuit between the battery and the starter, thus starting your motor and getting you grooving.
