How to Test Yamaha Golf Cart Solenoid First, disconnect the two small wires connecting the solenoid. Take a jumper cable and connect them from the positive and negative posts of the battery pack to the two posts on the solenoid that you just disconnected.
- The solenoid needs to be replaced IF the voltmeter shows a full battery voltage without a click.
- If your voltmeter stays at 0, the problem stems from somewhere else in your cart.
How do you test a Yamaha golf cart solenoid?
How to Test Yamaha Golf Cart Solenoid First, disconnect the two small wires connecting the solenoid. Take a jumper cable and connect them from the positive and negative posts of the battery pack to the two posts on the solenoid that you just disconnected.
Can you jump the solenoid on an electric golf cart?
The cart is a G16E. Help Please. 99% of the time when a electric golf cart stops suddenly it's a bad connection on a cable. You can jump the two large posts on the solenoid. It's best to use a set of jumper cables and connect to the solenoid first then connect the jumpers away from the solenoid, there will be sparks.
What are the symptoms of a bad solenoid on a golf cart?
Understanding what a solenoid is in a golf cart is vital for troubleshooting and repair. The common symptom of a bad solenoid is no clicks when the cart’s ignition is on and you press the accelerator. How do you test for a bad solenoid in your golf cart?
How do you troubleshoot an EZ GO golf cart solenoid?
EZ Go golf Cart Solenoid Troubleshooting. Try out the steps listed below to help troubleshoot the solenoid found in your EZ Go golf cart: Check to confirm if all the cable connections and wires are in place, as well as secure and tight. You must disconnect the negative battery cable before taking off the controller cover.
How do you test a Yamaha solenoid on a golf cart?
Turn on the engine of the cart and press the pedal downwards. If you hear a clicking sound, then it means that the low side voltage is working. But, if there is no such sound, it means that either there is no low side voltage or there is a problem with the solenoid. Use a voltmeter and engage the solenoid.
How do you test a solenoid on a golf cart with a multimeter?
Set your voltmeter to the ohms reading, and connect its probe to each one of the big terminals. Of course, the reading should be zero. Next, move the cart's switch to forward, turn it on, and accelerate slowly. Your solenoid should click.
Why will my golf cart go in reverse but not forward?
Check the Forward/Reverse switch of your golf cart for loose connections. If the connections are intact, interchange the top and bottom wires at the rear. If the cart now goes in reverse but not forward, the problem is with the switch. You have to just change the switch in this case.
How do you bypass the electric solenoid on a golf cart?
To bypass the solenoid of your golf cart, simply connect both the large side wires of terminals of the solenoid. And after making the connection, attempt to start the cart. If you fail to start, this is an indication that there is no problem with your solenoid.
How do I know if my golf cart solenoid is bad?
First, turn on the ignition while looking for a reading on the smaller terminals. If nothing is appearing, then press on the accelerator. If the needle doesn't move, then the problem is not with the solenoid. If it jumps and displays full voltage, then the solenoid is the problem and should be replaced with a new one.
How do you check if a solenoid is working?
0:111:43How to use a Multimeter: Solenoid Testing - Purkeys - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe have our meter set to ohms. If. You look at the two smallest posts here that is our coil. If weMoreWe have our meter set to ohms. If. You look at the two smallest posts here that is our coil. If we put our meter across it we will check and see what the coil resistance.
How does a golf cart forward reverse switch work?
0:139:43Golf Cart Forward and Reverse Switch Direction Selector Tutorial - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat is brand new it simply cables connect to the bright copper colored contacts. And the switchMoreThat is brand new it simply cables connect to the bright copper colored contacts. And the switch rotates through a hand action and that changes the polarity.
How do you fix a golf cart that won't go in reverse?
One possible cause of a cart not moving forward or in reverse is because of the way the wires are hooked in reverse. To fix this, you should switch the position of both the wires that are leading to the motor. If the golf cart is not rolling across freely, there might be an issue with the brakes.
How does a forward reverse switch work?
If the forward pushbutton is pressed, as long as the reverse coil is not engaged, current will find a path through the normally closed reverse contact and energize the forward coil, causing all contacts associated with that coil to change their state.
Can you jump a golf cart solenoid?
Bypassing Golf Cart Solenoid Method If you do decide to bypass the solenoid, this is what you need to do: Take the two larger wires that connect to the solenoid and connect them directly (keeping all safety precautions in place). This should do the trick and if it does not work then the solenoid is not the problem.
How do you jump a solenoid?
0:271:17How to Jump the Solenoid on your ATV or GoKart - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe're just going to put them out and then how we jump it is you could take any screwdriver PhillipsMoreWe're just going to put them out and then how we jump it is you could take any screwdriver Phillips or straight head and then we're going to connect the bolts.
What does the resistor do on a golf cart solenoid?
Its purpose is to maintain the capacitors within the controller at the battery pack voltage so that when the contactor closes, no arcing occurs. Resistor value is determined by battery pack voltage.
How to test golf cart solenoid?
A diode allows current to run in one direction, but not in the other. Testing the diode is a simple procedure. Remove the diode from the circuit and check the leads with a continuity tester.
How to tell if solenoid is bad on golf cart?
The common symptom of a bad solenoid is no clicks when the cart’s ignition is on and you press the accelerator.
Why doesn't my golf cart solenoid click?
This can be a faulty wire connection, but can also mean the solenoid is beginning to fail. The golf cart solenoid doesn’t click when the accelerator is pressed. This again can be faulty wiring or a failed solenoid.
What to do if your solenoid is not zero?
If the reading is not zero, then the solenoid is stuck and needs to be replaced. If the ohmmeter does read zero, set the cart to forward travel and turn the key switch on. Press the accelerator pedal (or have a friend do it) and you should hear a click. If you don’t hear a click, measure the resistance anyway.
How to check if a battery is low?
First, follow these steps: Step 1 – Check the battery voltage from the positive connection to the battery negative. A solenoid uses 12-18volts and low voltage will not activate the solenoid. Step 2 – If the voltage is low, check the cable ends for corrosion. Clean and charge the battery.
How to tell if a golf cart won't start?
The first and most obvious symptom is the golf cart won’t start. If it is a gas-powered cart, the engine doesn’t turn over, and if it is an electric cart, the cart doesn’t move. Now, on to the next symptoms…. The engine on the gas-powered cart starts, but the starter doesn’t disengage after starting.
Where are the solenoids on a golf cart?
In all golf carts, new and old, the solenoids can be found under the seat or in the engine well and are easily identifiable by the wires that lead to them. Banks of heavy duty solenoids, as in the previous illustration, are mounted on the side or back panel near the electric motor.
Why is my Yamaha golf cart not moving?
The main cause of a Yamaha golf cart clicking but not moving, is a faulty controller or solenoid. The battery has to be checked first to see if it’s delivering the right voltage while in the idle state as well as when the pedal is pressed. There can be other reasons for the Yamaha golf cart not moving though you hear the click.
How to check solenoid on G9 Yamaha?
The solenoid can be checked using an old screwdriver to jump the terminals. Your G9 Yamaha golf cart’s key must be in the start position. If the starter turns when you do this, your solenoid needs to be replaced. You must be careful while doing this crude test; there could be sparks when the two terminals touch.
Why is my solenoid not clicking?
The reason why the solenoid is not clicking could be that it is faulty or has no grounding. Experts recommend checking all wiring and cable connections to rule out this possibility. Batteries on your G16 Yamaha golf carts should raise sufficient power to reach the solenoid and the starter/generator.
What is a faulty controller?
The controller is one major component that may have to be replaced. A faulty controller can stall the cart and the click you hear must be from the solenoid. Test the solenoid to see if it is functioning properly. You will require a multimeter, preferably a digital one, or a DVM for this.
What to do if your G9 golf cart is not clicking?
If you find your G9 Yamaha golf cart not starting nor clicking, check the key components for damage. If you find the parts to in good condition, check the brushes in the starter/generator.
What are the settings on the M3?
The variable settings on the M3 allow a player to adjust the loft, lie, and face angles of the club, as well as create a variable fade or draw bias. Which can correct many swing or hit issues...
How to tell if golf cart solenoid is bad?
One of the most common and obvious signs of the bad solenoid is the golf cart's failure to start when you initiate the ignition process. Once you click the accelerator and turn on the ignition switch, it is supposed to send a signal to activate the solenoid and start the cart. If the cart does not start, there is a big possibility ...
What is a solenoid in golf carts?
Simply put, a solenoid is a device that can transform electrical energy into mechanical energy. It's a coil of wire which is used as an electromagnet. The solenoid has the capability of creating a magnetic field with the help of an electric current. Solenoids work as the “go switch”, which is a must for any golf cart.
Why won't my golf cart turn over?
For a gas golf cart, the most common symptom is the starter failing to engage, so the engine doesn't turn over. Starters have the responsibility of activating the flywheel. When the flywheel starts to work, the starter is supposed to disconnect.
Why is my golf cart not starting?
If the cart does not start, there is a big possibility of a damaged solenoid. Another reason for a bad solenoid is that the contacts are starting to get damaged due to overheating or high current passing through them. Note: You may not necessarily experience all of these issues to recognize bad solenoids on your golf cart.
How to check if a golf cart solenoid is silent?
On an electric golf cart, if the solenoid is silent – no clicking – use the setting voltmeter to DC volts using the 200 range. First, turn on the ignition while looking for a reading on the smaller terminals. If nothing is appearing, then press on the accelerator. If the needle doesn’t move, then the problem is not with the solenoid.
Why do golf carts have solenoid?
The solenoid is simply there to allow electricity to flow freely to the controller and motor which will result in a running golf cart. RELATED: 4 Signs you need to Replace your Golf Cart Batteries.
Why is my golf cart not clicking?
On an electric golf cart, the most common symptom is the solenoid is not delivering electricity to the controller when the vehicle’s ignition is turned on. In normal operating conditions, the solenoid clicks on and off with the ignition switch. A failing solenoid will generally not click. Two things could be going on here.
What does it mean when a golf cart solenoid goes bad?
Technically, in fact, a solenoid is a shape – a shape in which the length of something coiled is longer than the diameter of the coils. In engine starters, this refers to the smaller motor ...
What does a solenoid do when you turn the ignition?
Step by step, it looks like this: When you turn the ignition key, a small amount of electricity goes to the solenoid. The solenoid uses that small amount of juice to close two heavy-duty contacts that allows a large jolt of electricity to pass through the starter. The solenoid also sends a pinion gear forward, which is the device ...
Why won't my solenoid click?
The solenoid might not be getting enough electricity to do its work – which could be caused by loose connections, a weak battery or the coil wearing out.
Why do you use electrical tape on a solenoid?
When you do this, use electrical tape to seal the cable ends, so they won’t form a circuit by accidentally touching each other or connecting through a metal conductor inadvertently. Doing this will ensure the vehicle will not run while testing the solenoid.
What is a solenoid in a golf cart?
A golf cart solenoid is one of the major components of any golf cart. This part is essential regardless whether you own an electric or gas golf cart because both types primarily rely on a solenoid for their movement. What this means is whichever brand or model you choose for your cart, a solenoid is truly an indispensable part of the vehicle.
How to get a golf cart going without a glitch?
To get your golf cart going without a glitch, you most definitely need the solenoid of your cart to be functioning properly. Thus, it goes without saying that you must check this component occasionally to monitor its performance so that you don’t get stranded mid-way.
What is a solenoid wiring diagram?
A solenoid wiring diagram can be very helpful in guiding you about the various connections made to and from the solenoid. This can come in handy when you set out to troubleshoot a problem in your cart on your own. The solenoid wiring diagram is generally very simple, straightforward and self-explanatory.
What does the inductive throttle sensor do on a golf cart?
When you push down the pedal of the golf cart downwards, the inductive throttle sensor sends out the first low power signal to activate the solenoid on its low side and the speed controller. The low side is the steel rod of the solenoid.
How often do solenoids work?
Since solenoids need to work very frequently; turning on and off each time you use the cart, they are prone to wear and tear easily. This is not surprising as they can switch on and off as much as 1,500 times a day). One of the first indications that a solenoid is faulty is when your cart fails to start.
Why is my golf cart not clicking?
This may be because the safety reed switch is not working properly in the charger socket. There could be a loose connection of the MOLEX plug.
Why does my gas cart not turn over?
In a gas cart, a bad solenoid prevents the starter from being engaged and therefore results in the engine not turning over.
