
Tools required: Ratchet with 6″ extension, 10mm socket, 3mm hex wrench, feeler gauge. Remove the four bolts (B) and carefully pry the cover (A) off, ensuring the rubber gasket does not stick and tear against the engine head. Inspect the gasket and wipe clean before putting the cover back on after the adjustment.
Full Answer
How to adjust the carburetor on an EZGO gas cart?
EZGO Gas Cart Carburetor Adjustment 1 Adjust the idle jet pilot screw on the carburetor. This can be done by doing a 1/4 turn of the screw. 2 Do a valve clearance adjustment starting with the cold valve. ... 3 If the locknuts in the MCI engine have a size of 9mm and square heads, you’ll need a pair of needle-nose pliers and a 9mm socket.
How to replace a carburetor on a golf cart?
Remove the bolt connecting the air cleaner to the carburetor using a box wrench. Remove the air cleaner followed by the float bowl. You’ll need a screwdriver to remove the float bowl present at the carburetor bottom. Remove the main and idle jets connected to the carburetor. Their positions vary based on the model of the golf cart.
How to use a Mikuni carburetor on a golf cart?
Flip the choke lever of the Mikuni carburetor from side to side for about half a minute. The cart makes use of a Walbro carburetor with three-line vacuum pumps with connections as follows. One vacuum pump is connected from the gas tank to the fuel pump. The second vacuum pump is connected from the fuel pump to the carburetor.
What to do if your carburetor is not working?
Also, consider removing and dismantling the carburetor to clean each part followed by assembly and mounting. Check if the needle valve is getting seated properly. If not, replace the entire assembly. Sometimes, the float may also have to be replaced. Check if the float is stuck or the pin holding the float has got dislocated.

How do you clean the carburetor on a EZ Go golf cart?
2:1210:232003 EZ GO Golf Cart Carburetor Clean Out - YouTubeYouTubeStart of suggested clipEnd of suggested clipFrom this carburetor. Because that big plate that's holding. The air filter box it's a little bitMoreFrom this carburetor. Because that big plate that's holding. The air filter box it's a little bit difficult to get that screw loose. But you have to be patient and you'll be able to get it. Out.
How do you clean a carburetor on a gas golf cart?
Spray the carburetor body inside and out with cleaner. Use the tube nozzle on the spray can to clean the jet ports, idle adjustment port and the choke plate. Use the bristle brush to clean dirt and deposits on the body. Wipe the carburetor with a dry cloth.
How do you take apart a carburetor to clean it?
Directions for Cleaning a Carburetor:Dilute cleaner. In a large container, mix 1 part Simple Green Pro HD Heavy-Duty Cleaner to 3 parts water.Clear air filter. ... Remove the carburetor. ... Remove carburetor float. ... Remove other removable components. ... Soak and scrub components. ... Rinse and dry. ... Reassemble and replace.
Can you clean a carburetor without removing it?
Use carburetor cleaner to remove deposits, clogs & debris Deposits inside the carburetor can clog fuel and air passages and reduce performance or stop the engine altogether. Luckily, you can take care of many of these problems quickly and easily; often without even removing the carburetor from the engine.
How do you clean a golf carburetor?
0:1410:06GOLF MK1.HOW TO SERVICE & CLEAN A CARBURETOR.KEIHIN ...YouTubeStart of suggested clipEnd of suggested clipNext you need to just remove your airbox. So that you can be clear with your carburetor to work on.MoreNext you need to just remove your airbox. So that you can be clear with your carburetor to work on. And then you remove everything that is attached to the carburetor. Like your cables.
How do you adjust the carburetor on a EZ Go golf cart?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
How do I know if my carburetor is clogged?
4 Signs Your Carburetor Needs CleaningIt just won't start. If your engine turns over or cranks, but doesn't start, it could be due to a dirty carburetor. ... It's running lean. An engine “runs lean” when the balance of fuel and air gets thrown off. ... It's running rich. ... It's flooded.
How do you clean a gummed carburetor?
3:4812:18How to Clean the Carburetor of a Small Engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can use carburetor cleaner squirt a little in there. And you can scrape it a little bit or rubMoreYou can use carburetor cleaner squirt a little in there. And you can scrape it a little bit or rub it around and get that varnish off the bottom of the carburetor.
Will seafoam clean a gummed up carburetor?
After removing gasoline from the tank and carburetor, add a mixture of Sea Foam followed by 8 ounces of fresh gasoline (1 to 2 ratio). 5. With the cleaning mixture in the fuel tank, crank/prime/rope-pull the engine to draw the cleaning mix into the carburetor(s). 6.
Can you use wd40 as carb cleaner?
0:001:26Throttle Body, Carb & Choke Cleaner - WD-40 Specialist Automotive RangeYouTubeStart of suggested clipEnd of suggested clipYou can safely spray throttle body carbon choke cleaner straight down the carburetor throat orMoreYou can safely spray throttle body carbon choke cleaner straight down the carburetor throat or throttle body.
Can I spray carb cleaner into the air intake?
2:004:49How to clean a gasoline carburetor upper engine (air intake) using Sea ...YouTubeStart of suggested clipEnd of suggested clipI just insert the straw into the carburetor throat. I'm going to spray the whole hand it's going toMoreI just insert the straw into the carburetor throat. I'm going to spray the whole hand it's going to take about four minutes can be running at the intake valve and through the chamber.
How do you clean a carburetor without carb cleaner?
2:186:40How To Clean Carburetor Jets Without Carb Cleaner - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn this solution that I have back here right here is just peroxide. I used to just kind of hopefullyMoreIn this solution that I have back here right here is just peroxide. I used to just kind of hopefully eat up some of the ethanol. This new gas is nasty. It just makes everything gummy.
How to adjust carburetor on golf cart?
In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
How to remove cable from carburetor?
Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.
How to replace carburetor float?
Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.
Why does an EFI carb require more maintenance than an EFI?
The carb requires more maintenance than an EFI because of the cleaning and rebuilding of the carburetor involved.
Why does my carburetor flood on my golf cart?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.
How to cool down a golf cart?
Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.
Which is more powerful, carb or EFI?
The carb model is more powerful as well as starts and goes faster when compared to the EFI. The EFI experiences delay to start moving when the pedal is pressed.
