Golf-FAQ.com

how to compress coil springs without tool ezgo golf cart

by Caroline Klein Published 3 years ago Updated 2 years ago

How to start an EZGO golf cart?

Pulser coils can be fried, and the only way to start a EZGO golf cart is by replacing the coil. You can test the coil and use follow the below steps to remove and install a new one. The HEI model should be grounded. The mounting ring should be appropriately placed. The screws should be attached centrally.

What's the EZGO gas golf cart code 793317?

Have an EZGO gas golf cart with manufacturer's code d1394 and serial number 793317. It has a two cylinder engine and has no spark from either ignition coil wire.

What is the no spring compressor method?

The No Spring Compressor Method is a way of disassembling your shock assembly (or coilover) without the use of a spring compressor tool. In your coilover/shock assembly, you have a spring that is compressed by a shock between the upper and lower perches, which are connected to the shock.

How do you test a Pulser coil on an EZGO golf cart?

How to test a pulser coil on an EZGO golf cart A voltmeter can be used to test the pulser coil or the igniter of a golf cart. This will tell you if the coils are damaged or there is some other larger problem hidden underneath the golf cart. Check the user manual to know the exact location of the pulser coil under the seat.

How do you compress coil springs without tools?

1:093:21Cheap & Easy Spring Compressor - DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm just putting on there same place underneath the control arm. And then I fix the ratchet strapMoreI'm just putting on there same place underneath the control arm. And then I fix the ratchet strap around a number of different positions on the coil on the spring there. And then I lowered.

How do you change a coil spring without a compressor?

1:057:26How to Replace Coil Springs Without Compressors | Ford F150 - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you'll either want to put your jack stand and Jack under your other beam here and or underneathMoreSo you'll either want to put your jack stand and Jack under your other beam here and or underneath one of the frame rails in the back but as long as it's not the way this you should be fine.

How do you compress coil springs?

0:048:57Easiest way to compress coil springs! (toyota) - YouTubeYouTubeStart of suggested clipEnd of suggested clipSafe as well versus using the the clamps that you put on each side and you have to crank down toMoreSafe as well versus using the the clamps that you put on each side and you have to crank down to compress the spring this is much easier so all i've done is taken off the wheel.

How do you compress a spring for installation?

0:334:01HOW TO COMPRESS STRUT SPRING - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's very important to place the locking pins in place otherwise. Nothing can kill you. It's you KenMoreIt's very important to place the locking pins in place otherwise. Nothing can kill you. It's you Ken don't get me wrong this is a little bit dangerous job messing with Springs because they're very.

Are spring compressors safe?

Compressing springs is a very dangerous job. The energy that compressed springs pack is tremendous. If your redneck, home-made coil spring compressor were to fail it could literally crack your skull, take your face off and even kill you.

How do you disassemble a coil spring?

7:1811:59How to remove and disassemble struts - suspension episode 6YouTubeStart of suggested clipEnd of suggested clipYou can now get your impact wrench and remove the top nut now removing the top nut. Without anMoreYou can now get your impact wrench and remove the top nut now removing the top nut. Without an impact wrench is really really hard so I definitely recommend an impact wrench for this. Job.

Can you compress a coil spring with ratchet straps?

0:232:04How to compress a coil spring with ratchet straps - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust like pulleys you strap you start on one and up over under up over and keep going up and down upMoreJust like pulleys you strap you start on one and up over under up over and keep going up and down up and down up and down so every time you go to pull this.

How do you depress springs?

2:176:15How to compress suspension coil springs safely - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust do it slowly take your time with it there's no rush. Just do so many clicks out on each. Side.MoreJust do it slowly take your time with it there's no rush. Just do so many clicks out on each. Side. This makes your it compresses evenly perhaps do count up in tones.

Can you compress a shock by hand?

You cannot judge the strength or condition of a shock/strut by hand movement alone. The force and speed generated by a vehicle in operation exceeds what you can accomplish by hand. The fluid valves are calibrated to operate differently depending on the degree of movement inertia which cannot be duplicated by hand.

How do you make a small valve spring compressor?

0:193:31Home Made Valve Spring Compressor: for small motorcycle ...YouTubeStart of suggested clipEnd of suggested clipThis little piece of wood. And I made it into a fork shape. So here's the back end of the valve. AndMoreThis little piece of wood. And I made it into a fork shape. So here's the back end of the valve. And here's the spring inside here and just enough to straddle.

How do you compress a large spring?

6:4010:11How to compress a coil spring or strut using a Macpherson ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSimply just pick it up you can screw this by hand it's really easy. And you just want to compress itMoreSimply just pick it up you can screw this by hand it's really easy. And you just want to compress it down again because we want to get into the center not on the ends.

How do you make a valve spring compressor?

1:515:5439¢ DIY Motorcycle Valve Spring Compressor || IT WORKS! - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen i took my 39 insert plug that into the top of the valve spring then i compress the spring i'mMoreThen i took my 39 insert plug that into the top of the valve spring then i compress the spring i'm now cranking on the uh threaded portion of the c-clamp.

How do you remove front coil springs?

0:221:17Replacing Coil Springs | Hot Rod Garage Tech Tips (Ep. 36) - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's possible for the spring to fly out of control for conventional coil spring the right tool isMoreIt's possible for the spring to fly out of control for conventional coil spring the right tool is the one that slides up the center of the spring.

How do you remove a spring from a strut?

3:336:51How to Disassemble a Strut and Replace the Shock - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can use a couple wrenches for the disassembly. One to hold the shock shaft in place fromMoreYou can use a couple wrenches for the disassembly. One to hold the shock shaft in place from spinning and the other to remove the nut.

How do you remove a front suspension spring?

Part 1 of 1: Replacing the suspension springsMaterials Needed. ... Step 1: Remove power from the vehicle. ... Step 2: Locate the springs and the strut connections. ... Step 3: Raise the vehicle. ... Step 4: Remove the wheel and tire. ... Step 5: Remove the lower control arm bolts. ... Step 6: Lower the control arm and remove the spring.More items...•

How do you replace rear springs on a car?

0:063:04How to DIY replace the rear springs - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou have to counter hold it from the rear. And then zip it up. Once it's loosened you can pull itMoreYou have to counter hold it from the rear. And then zip it up. Once it's loosened you can pull it out now if it's under tension that means that it's being pressed on by the lower control arm.

How to get a car off a jack stand?

First, jack up the front of the vehicle and support it on jack stands. Remove the wheels. You may set them aside, or place them below each side of the vehicle as an extra safety precaution in the case the jack stands fail. Finally, make sure to chock the rear wheels with wheel chocks so that the car will not roll and cause the car to come off of the jack stands.

What happens when you disconnect shock nut?

However, when you disconnect that top center shock nut, the shock’s top center threads are still sticking out of the strut mount. Therefore, it is still supported from lateral movement.

Can you compress a spring?

Therefore, you can’t compress the spring anymore, even if you still have more to compress. Another problem that I’ve seen is that these tools typically instruct you to hand-tighten these tools with a ratchet, but in most cases folks use air wrenches or impact wrenches when they shouldn’t, simply due to the ease of use.

Can you remove a lower shock to LCA bolt?

You should be able to move the spring around and be able to feel that there is no compression on the spring. Now, you can now remove the lower shock to LCA bolt.

How to tell if a golf cart has low compression?

To check if pressure is escaping your golf cart’s engine, you have to check the compression in the cylinders of your engine using a compression gauge.

What causes low compression on a Yamaha golf cart?

Yamaha golf cart engines in general have a pretty common problem that causes low or no compression; misplaced push rods. A push rod that’s not under the rocker arm will cause a compression problem. This is easy to check and relatively simple to fix.

How to remove a rubber boot from a cart engine?

Without using too much force, remove the rubber boot from the spark plug. Put a socket wrench over the spark plug and loosen it till you can remove it from your cart engine. Put the choke in the off position.

What is compression ratio?

Compression ratio is the ratio you get when you compress the max cylinder volume of your cart engine into the min cylinder volume of your cart engine. This is the volume of your engine’s cylinder when one of its pistons goes all the way down compared to when one of its pistons is all the way at the top. As an example, you’d say an engine has ...

How to fix a cart engine that is not getting enough oil?

This means that the top parts of your engine are not getting enough oil. Simply tightening the valves should fix your compression issue. If there’s not enough oil getting to the top parts of your cart engine, there’s a way to fix it. Remove the steel tube that goes through the back of the motor. Blow through it .

Why won't my G16 run?

If your G16 has a broken accelerator cable then it won’t be able to run because there’s no compression. If your accelerator cable is broken, then you can’t fix it and must replace it. Replacing the accelerator cable should fix the compression issues in your G16.

What causes a cart to have low compression?

A clogged exhaust. If your cart engine can’t pull in fresh air, then it’ll have low compression. So if your exhaust is clogged, your cart engine gets low compression. To fix this, just clean out your cart’s exhaust and make sure your exhaust is functioning properly in general. A bad gauge.

What is the purpose of a golf cart pulser coil?

The purpose of the Pulser coil is to give ignition signals to the engine and ignition system. The resistance categorizes pulser coils.

How to remove coil from flywheel?

To remove the coil, the flywheel needs to be detached. Use a balance styled puller and attach the same to the threaded holes. Now add some pressure and let the puller do its job by removing the flywheel.

How to adjust a pulser coil?

The screws should be attached centrally. To adjust the coil stability, replaced the coil wire or the coil. Switch the coil wires to adjust the pulser.

Where is the pulser coil located?

The location of the pulser coil is under the cart’s seat and is near the engine. It is better to use a user manual to locate the coil so that it can be tested or replaced. If there is no spark, there is always a requirement to check if the coil is working fine.

Is the Ping G25 adjustable?

Is the Ping G25 driver adjustable? The Ping G25 driver is adjustable. It’s possible to do four adjustments using the hosel adapter of the driver apart from the stated loft setting and...

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9