How do you adjust the throttle cable on an EZGO golf cart?
How do you adjust the throttle cable on an EZGO golf cart? Close the carburetor throttle plate.. Rotate the governor arm in a counter-clockwise direction.. Keep the cable inside the throttle cable bracket that is fitted on the rear axle.. Make sure that the governor and carburetor are seated with ...
Why is my EZGO carburetor smoking?
The exhaust emanates black smoke because the engine utilizes excess fuel or runs rich. The golf cart experiences hard starting because of an improper air-fuel ratio. The table given below offers some tips to troubleshoot your EZGO golf cart carburetor.
How do you adjust the throttle cable on a carburetor?
Bypass the governor and connect the throttle cable to the carburetor directly. Before adjusting both the throttle cables, you must turn the main switch OFF. Block the wheels and take off the rear access panel. Adjust the throttle cable from the governor to the carburetor by turning the governor lever in the counterclockwise fully.
What does a throttle cable do on a golf cart?
It ensures that your golf cart operation is smooth and safe. A throttle cable assists in the efficient utilization of the batteries and gas of the golf cart. How do you adjust the throttle cable on an EZGO golf cart?
How does throttle cable go into carb?
0:2317:15Route Throttle Cable & Install Carburetors on a CB350 ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipStraight out and then over and straight down onto.MoreStraight out and then over and straight down onto.
How do I reconnect my throttle cable?
0:081:11Removing Throttle Cable from Throttle Body - YouTubeYouTubeStart of suggested clipEnd of suggested clipBody what I normally do is I take a ballpoint pen like this push down on the throttle arm here getMoreBody what I normally do is I take a ballpoint pen like this push down on the throttle arm here get underneath the cable. Move it all the way to the end like this just pop the cable right off.
How do I install an accelerator cable?
Push the new cable through the firewall and into the engine compartment. Step 2: Hook the new cable up to the accelerator pedal. Slide the new cable through the slotted hole in the accelerator pedal. Step 3: Reconnect the throttle cable to the retaining bracket.
How do you adjust the throttle cable on a EZ Go golf cart?
2:446:13How to Adjust Governor on EZGO RXV Gas Golf Cart | Speed IncreaseYouTubeStart of suggested clipEnd of suggested clipLess exposed in other words we want to get this housing pushed back in order to do that we'll takeMoreLess exposed in other words we want to get this housing pushed back in order to do that we'll take this outer nut loose. And run it closer to the edge. Then move the jamb nut up closer to it.
How do I get my throttle snap back?
0:484:15Throttle grip not snapping back - a new look at things - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just anything really you just push down on it. So you see it's push down stance. Right back pushMoreAnd just anything really you just push down on it. So you see it's push down stance. Right back push down on it snaps right back so you know that it's not the spring.
Which throttle cable is push and pull?
What are Push/Pull Cables? A push/pull throttle is a dual cable throttle operation where the pull cable opens the throttle plates, while the push cable, along with a throttle return spring, closes the throttle plates. The “push” cable is a misnomer as the push cable also pulls.
How do you thread a throttle cable?
8:1711:33How To Replace a 2 Stroke Throttle Cable - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo be sure to stop threading in your throttle cable before it reaches the spot where it can makeMoreSo be sure to stop threading in your throttle cable before it reaches the spot where it can make contact with the pulley. So at this point we'll set the lock. Nut.
How throttle and choke linkage is setup on a Briggs 2 piece carburetor?
4:4416:03How Throttle and Choke Linkage is Setup on a Briggs 2 ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can see the carburetor when this is a plastic part this piece tends to break a lot on these. IfMoreYou can see the carburetor when this is a plastic part this piece tends to break a lot on these. If you look at the linkage here it runs from here hooks into the governor arm back here.
How do I install a universal throttle cable?
4:576:58Lokar Universal Throttle Cable on 72 Mustang - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut basically what you do is you trim this first to your point of your bracket. Then you run yourMoreBut basically what you do is you trim this first to your point of your bracket. Then you run your cable through and you connect it to your gas pedal.
How do I speed up my EZ Go gas golf cart?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
How do you adjust the carburetor on a EZ Go golf cart?
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
How do you bypass the governor on a EZ Go golf cart?
0:000:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the farther you bend that normally the faster it goes and then that's it basically when you wantMoreSo the farther you bend that normally the faster it goes and then that's it basically when you want to return your heart you just bend that back down and go back to normal speed.
What happens when accelerator cable breaks?
When the accelerator cable fails, it will physically break or snap. It is generally uncommon for this to occur without some warning signs. Before it breaks, it is likely that there will be signs that the material of the wire is wearing down and that there may be a problem with your accelerator cable.
How do you change an accelerator cable and adjust it?
2:5010:02How to Replace Your Accelerator Cable And Adjust It - YouTubeYouTubeStart of suggested clipEnd of suggested clipRemove the bulkhead cablegram.MoreRemove the bulkhead cablegram.
What can a loose throttle cable cause?
Improper cable adjustment and slow acceleration response This can also result in the opposite effect as well, in that the excess slack can create a delayed throttle return response. This can cause more throttle to be applied unintentionally, creating a dangerous situation.
How do you fix a throttle?
0:302:53How To Replace A Bad Electronic Throttle On Your Car - YouTubeYouTubeStart of suggested clipEnd of suggested clipGet a new one don't get a Rheem and the reman ones aren't that good the new ones are much betterMoreGet a new one don't get a Rheem and the reman ones aren't that good the new ones are much better then you put a new gasket. In slide the throttle assembly over it. And then bolt it back on snog.
How to adjust carburetor on golf cart?
In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
How to remove cable from carburetor?
Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.
How to replace carburetor float?
Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.
Why does an EFI carb require more maintenance than an EFI?
The carb requires more maintenance than an EFI because of the cleaning and rebuilding of the carburetor involved.
Why does my carburetor flood on my golf cart?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.
How to cool down a golf cart?
Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.
Which is more powerful, carb or EFI?
The carb model is more powerful as well as starts and goes faster when compared to the EFI. The EFI experiences delay to start moving when the pedal is pressed.
For the 295cc or a 350cc twin-cylinder OHC engine. 1991 – Present
Tools required: Ratchet with 6″ extension, 10mm socket, 10mm socket wrench, flat blade screwdriver, and a feeler gauge. Note: if the screw (C) has a square head instead of a flat blade slot, this takes a tool designed just for this purpose.
For the Kawasaki FJ400 401cc 4-cycle Single Cylinder 1996 – Present
Tools required: Ratchet with 6″ extension, 10mm socket, 3mm hex wrench, feeler gauge.
What happens if you don't adjust your golf cart?
If there's no adjustment left the cable must be stretched. As long as you're getting full throttle and the golf cart is running fine at slower speeds I wouldn't worry about it.
Does the butterfly carburetor need to be adjusted?
No it sounds like the cable needs to be adjusted. The carburetor butterfly should start to open right after the micro switch activates and should close just before the micro switch clicks.