- Determine how much of the shaft’s tip you wish to trim. ...
- Place the shaft into a rubber golf club clamp, then insert the clamp into a vise. The rubber protects the graphite from damage.
- Wrap two or three layers of masking or electrical tape around the area to be cut. The tape helps prevent the shaft from splintering.
- Measure the distance that you wish to trim from the tip, then mark the distance on the tape with a pen.
- Cut carefully along the marked line with a hacksaw, insuring your blade is perpendicular to the shaft.
- Determine how much length must be trimmed from the butt end of the club. This typically depends on the type of club you're constructing.
- Tape and mark the area to be cut, as you did with the tip. However, add 1/8 inch to the cut to account for the grip cap.
- Cut the butt end the same way as you trimmed the tip. Sorry, the video player failed to load.
How do you glue a graphite Golf Club shaft?
Steps to Remove a Graphite Shaft:
- Keep the shaft in a graphite shaft extractor following the instructions given for the extractor.
- Apply heat on the hosel with a heat gun.
- Use a box wrench to turn the threaded bolt of the extractor without twisting the clubhead.
Which blade to cut a graphite shaft?
- Vise
- Hack Saw with Blade to Cut Graphite
- Dremel Tool
- Masking Tape
- Yard Stick, Ruler
- Marker
How to coat steel with graphite?
- Improved uniformity
- Improved material consistency
- Improved lifetime
- Higher chip yields possible through improved photoluminescence
How to trim a golf club shaft?
To do that, the DIY golfer will have to:
- Remove the existing grip.
- With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw.
- Re-install a grip on the newly shortened shaft.
- And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. ...
Can you cut a graphite golf shaft?
Yes, it is even strong enough to cut steel. It can cut through a graphite shaft in 15-20 seconds after the shaft has been securely place in your vise. The model we sell fits on a standard 12” hacksaw frame found at any hardware store or in many home shops.
How do you shorten a graphite driver shaft?
With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. Re-install a grip on the newly shortened shaft.
Where do you cut golf club shafts?
The butt end of the shaft is grip end. If you are shortening or extending the length of a golf club, this is where you will cut. If you want to change the play-ability of the club (feel, flex to a certain extent, spin rate, dispersion), you will be cutting the tip end of the shaft.
What do you use to cut a driver shaft?
0:394:01How to Cut Golf Shaft DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou need a pipe cutter.MoreYou need a pipe cutter.
How do you cut graphite?
Most people like to use a hack saw with a blade that can cut graphite. Many golf club part manufacturers will sell blades like this, and they are usually easy to install on your current hack saw. A typical hack saw blade is probably not going to do the trick. Many people also use a Dremel-type tool.
How much does it cost to cut a golf shaft?
Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.
Can you cut your own golf clubs?
If you have purchased a set of used golf clubs that are too long, you can quickly cut them down to size with a hand-held rotary tool. You can also resize your old clubs and pass them on to your children. The shaft of a golf club is narrower at the head end to generate power on the swing.
What happens when you butt trim a shaft?
1:363:54How Does Butt Trimming a Golf Shaft Affect Playability? - YouTubeYouTubeStart of suggested clipEnd of suggested clipChange when cutting one inch or less or or more off of the butt end probably. The biggest downsideMoreChange when cutting one inch or less or or more off of the butt end probably. The biggest downside of cutting. Or making a closed shoulder is the effect that it has on swing weight.
How do you measure and cut a golf shaft?
1:093:56Mitchell Golf | Measuring and Cutting Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo when we cut will be an eighth of an inch short of our playing length to ensure that the butt capMoreSo when we cut will be an eighth of an inch short of our playing length to ensure that the butt cap of the grip measures exactly on our playing length.
Should I cut down my driver shaft?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
Does cutting a golf shaft make it stiffer?
When you cut off a portion of the softest part of a golf shaft (the tip), it increases the overall stiffness. The handle section of a shaft, on the other hand, is longer and more uniformly stiff, so removing material from the handle does not make such a pronounced difference in overall stiffness.
Can I cut down my driver shaft?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
How much does it cost to shorten a driver shaft?
Generally, this fee will be about $15 to $35 depending on where and when you get the work done. Replacing a shaft on a driver is a bit more work than regripping a club.
How long should your driver be based on height?
Tony Finau is one of the tallest golfers on the PGA Tour at 6'4″, and his driver's length is usually around 45 inches. Both Finau and Fowler are two of the longest drivers on the PGA Tour....Driver Shaft Length Based Solely on Height.Height (feet/inches)Driver Shaft Length5'0″-5'2″44.5″4'10”-5'0″44″< 4'10”43″7 more rows•May 9, 2021
Does shortening a golf shaft make it stiffer?
A shorter shaft is typically stiffer than a longer one. Although a shorter golf club shaft tends to be firmer than a longer one, it is important to understand the changes trimming a shaft will make to a club before making such a permanent change.
Remove the Grip
The first things to do is to remove the grip tape from the golf club [how to remove grip tape from golf club]. This will make it easier to cut the shaft. You can use a cutter to slice the grip from the top and slowly peel it off the club. The specific process can differ, which will depend on the material of the grip.
Measure the Shaft
With the grip now off the golf club, the next step is to take the appropriate measurement. Use a measuring tape and run it from the top to the bottom of the shaft. Mark the specific spot where the measurement ends. You can do this with a marker or by wrapping the tape around the tip. The measurements should be as precise as possible.
Cut the Shaft
Now comes the most important part of the task. Before cutting the shaft, make sure that it is in a stable position. Some might think that they can cut by holding the shaft with one hand, but this isn’t the case. For your safety and to make the cut more accurate, we recommend placing the golf club in a vise.
Wrap a Grip Tape
Once you are done cutting, the next step is to wrap it using your grip of choice. Pick a material you are comfortable with. This is important since it is the part that you will be holding, and hence, it will affect how you swing the club. Also, it must absorb vibration, making sure of your highest level of comfort, even during aggressive shots.
Why use masking tape on graphite shafts?
Secondly, by wrapping tape around the shaft, reduces the likelihood that the shaft would splinter during the last moment of the cutting process.
What is a rod saw blade?
Even for veteran clubmakers, the rod saw blade is handy to cut a single shaft instead of firing up your motorized equipment or to find that you have a damaged blade in need of replacement. Plus it comes in handy cutting the shaft angle and through bore plugs for those golf club thru bore installations. All-in-all, it is a long-lasting tool no golf ...
Can a rod saw cut graphite?
It makes thin straight cuts in all types of shaft materials used in golf. Yes, it is even strong enough to cut steel. It can cut through a graphite shaft in 15-20 seconds after the shaft has been securely place in your vise. The model we sell fits on a standard 12” hacksaw frame found at any hardware store or in many home shops.
Can a hacksaw cut steel?
Yes, it is even strong enough to cut steel. It can cut through a graphite shaft in 15-20 seconds after the shaft has been securely place in your vise. The model we sell fits on a standard 12” hacksaw frame found at any hardware store or in many home shops. How To Tips. I would like to share a few how-to tips as well.
Can you cut graphite shafts?
Graphite shafts need special care to be cut properly. A tubing cutter, that you would use to manually cut a steel golf shaft, will crack or destroy a graphite shaft in no time at all. Don’t think about pulling the hacksaw from your tool chest either.
Feedback
Hey guys. I want to cut a half inch off my driver shaft. I've done a lot of searching but am not finding a definitive answer. I know you need to wrap the area you're cutting in masking tape but what's not clear to me is the correct type of blade to use. Some say hacksaw, others say a chop saw (which I have to admit, I have no idea what that is).
Feedback
i've used a dremel -- or a chop saw. either work fine. hacksaws COULD splinter the ends --not sure if it's 100% true but, i'd rather not risk it.
Feedback
I used a miter box and hacksaw with a blade with the highest number of teeth per inch (TPI) I could find at the hardware store. Came out just fine.
Feedback
What is a chop saw? I have a dremel but what attachment should be used? Also, if using a dremel, how do you get the cut perfectly straight?
Feedback
I'll use anything that has fine sharp teeth. I've done most of my shafts by hand recently because I have limited space and its easier without needing electricity and cords.
Feedback
Dremel cutoff wheel. They use a similar abrasive material circular saw blade as a chop saws uses (which is what you will find at a club maker for cutting graphite shafts). I use it for my graphite shafts as well as my carbon fiber arrows for my compound bow. Never had problems with either.
Feedback
Chop saw is best, Dremel with cutoff wheel will work (but it is tough to make an even cut), and if you use a hacksaw get a 'grit' blade.
How to trim graphite shaft?
Step 1. Determine how much of the shaft’s tip you wish to trim. The graphite shaft will come with trimming instructions that tell you how much to cut from the tip, depending on the amount of flex you want. For example, you’ll trim more off the tip to achieve a stiffer flex.
How to protect graphite from damage?
Place the shaft into a rubber golf club clamp, then insert the clamp into a vise. The rubber protects the graphite from damage.
How to cut a line with a hacksaw?
Cut carefully along the marked line with a hacksaw, insuring your blade is perpendicular to the shaft. The Clubmakers.co.kr site suggests using a grit edge blade in your saw.
Series Navigation
I know this might seem obvious, but be sure to measure and mark off the point at which you are cutting. Especially while tipping a shaft (you can’t undo this), it is important to have precise measurements. Use a sharpie to make your marks on the shaft. Here is a tutorial on how to measure golf clubs.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
