- Measure the desired new length of club. With the measuring tape, measure the desired length to be cut off.
- Cut the club at the desired length. Using the hack saw, carefully cut the club where you marked it. Be sure keep fingers away from blade for your safety.
- Wait 10-15 minutes for shaft to cool off. The metal you just cut will be hot so set it aside for several minutes and allow to cool down.
- Sand/dull the end of metal that was just cut. Take the sand paper and carefully smooth the end of the shaft.
How to shorten a golf club?
How to Shorten Golf Clubs 1 Insert the golf club into a shaft clamp and tighten the clamp to keep the club from moving around while you work on the grip. 2 Use a utility knife to cut the side of the existing grip. Pull off the grip and discard it. ... 3 Wrap masking tape around the area of the shaft that will be cut. ... More items...
How do you remove the grip from a golf club shaft?
Remove the grip tape from the shaft. Measure the amount of shaft you want to remove (add an additional 1/8 inch to make up for the end of the grip), and mark the spot with permanent marker. If it is a graphite shaft, wrap two layers of masking tape around the cut location.
How to cut a golf club in half?
1 Measure the desired new length of club. With the measuring tape, measure the desired length to be cut off. 2 Cut the club at the desired length. Using the hack saw, carefully cut the club where you marked it. ... 3 Wait 10-15 minutes for shaft to cool off. ... 4 Sand/dull the end of metal that was just cut. ...
Why do golfers cut down shafts and reinstall them?
But some do-it-yourself golfers also cut down golf shafts, then reinstall them in their clubs. They do this to make their clubs better fit their swing, which might mean cutting the shaft simply to change length, or to change swingweight, flex or other playing characteristics.
How do you cut golf clubs at home?
0:363:03Golf Tips : How to Trim Golf Club Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipGood measuring stick a marking pin will need a chop saw that we can chop with and we'll also need aMoreGood measuring stick a marking pin will need a chop saw that we can chop with and we'll also need a grinder just to trim off the burner off the end of it before the club is reesh aft.
How much can you shorten a golf club?
Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club. Taking 2 inches off will change the flex of the club. If you are shortening irons, every 1 inch you shorten the club will make the iron effectively play 2 degrees flatter.
Is it bad to shorten golf clubs?
For most golfers, having clubs that are too short will be better than if they're too long, but can still result in inconsistent shots. Clubs that are too short will make you stand bent over, which can cause back pain. You'll also have the tendency to push the ball a lot.
Can you cut your own golf clubs?
If you have purchased a set of used golf clubs that are too long, you can quickly cut them down to size with a hand-held rotary tool. You can also resize your old clubs and pass them on to your children. The shaft of a golf club is narrower at the head end to generate power on the swing.
Can I cut my irons to one length?
1:2210:28I cut down my long irons - One length irons combo - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I took my Wilson v6 I played off my sex iron. So I made six iron 5-iron and for iron all the sameMoreSo I took my Wilson v6 I played off my sex iron. So I made six iron 5-iron and for iron all the same length. So my Wilson V SEC sounds were already an inch longer than standard.
How do you tell if your clubs are too long?
How to Tell if Your Golf Clubs are Too LongCompletely upright posture.Improper golf swing.Odd ball flight.Feels cumbersome and unmanageable.Shaft feels weak.Consistency hitting with the toe.The measurements are wrong.
Does cutting down a shaft make it stiffer?
"Cutting more of the grip end will still stiffen the shaft a little bit, but only because in doing so you make the shaft shorter, and not nearly as much as when trimming more from the tip end."
Can I cut my driver shaft down?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
Does shortening a shaft make it stiffer?
Shortening the shaft will make the club shorter but it will also make the shaft stiffer and adjust the swing weight as well. Plus, the more length you remove, the less flex your club will have. Depending on how much you cut it down, it could move a regular flex to a stiff or a stiff to an extra stiff.
Should shorter golfers use shorter clubs?
Shorter golfers are often better served with shorter clubs, while the lie angle (how the club sits on the ground) may also need tweaking. If your clubs are too long and/or upright, you'll be forced to adjust away from a swing that's natural for you.
How does shortening club affect lie angle?
Cutting length from or adding length to a shaft will not alter the angle between the hosel and the sole. What it will affect is the "effective lie".
Should I shorten my 4 iron?
A shorter club technically should improve control and accuracy. A longer club technically should increase distance. A club that is properly fitted in terms of the length of the shaft will maximize accuracy and distance.
How to shorten a golf club shaft?
To do that, the DIY golfer will have to: 1 Remove the existing grip. 2 With steel shafts, use a tubing cutter to trim the shaft; with graphite shafts, shorten using a hacksaw. 3 Re-install a grip on the newly shortened shaft. 4 And, most importantly, Wishon says, add weight to the clubhead in some manner to restore the swingweight feel of the club. "If clubs are shortened and no weight is added back to the clubhead, the chances of the length reduction having the desired effect are somewhere between slim and none."
What is the difference between a golf shaft and a tip?
All golf shafts taper; that is, their circumference is greater at the grip end than at the tip end. That means that the grip end is the strongest part of the shaft and the tip end the weakest, which, Wishon says, leads trimming to have different effects: "Cutting more of the tip will have the effect of getting rid of some of the weaker end ...
Should the reduction in length be made from the grip end only?
"If the goal in making the clubs shorter in length is a desire to gain an improvement in accuracy, the reduction in length should be made from the grip end only ," Wishon said.
What to do when cutting a golf club down?
The first thing that you need to do when you’re cutting a club down is to get the old grip out of your way. In order to do that safely, you need to have plenty of space to work in and a way to hold the club steady while you’re cutting. That’s where the prepared workspace and the vice come in.
How to get adhesive off of golf club?
Heating the tape up will soften the adhesive and make this step easier. Heat the adhesive with a heat gun or a hairdryer. Peel the tape off until you have removed it all from the shaft of the club.
How to get better adhesion on a grip?
It will also emulsify the adhesive and help it to get better surface adhesion with the inside of the grip. Plug the small hole in the top of the grip with a finger and turn the grip upside down. Spray some adhesive into the inside of the grip.
How long does it take for a grip to dry?
Once you have the new grip in place, you will need to let the adhesive dry and cure. It will take approximately 6-8 hours for a full cure.
How to cut yourself with a razor blade?
Put a fresh blade in your razor knife. A sharp blade cuts easier and that protects you from having to push or pull too hard, which could expose you to a higher risk of cutting yourself. A hook blade makes this step easier and safer. Slice through the grip until you have cut it from top to bottom.
What tool to use to cut graphite shaft?
For steel shafts, a hack saw is the best option for a clean cut. For graphite clubs, you will need to use a rotary tool with a cutting wheel to get the best cut possible. Cut the desired amount from the shaft. Be careful to avoid cutting yourself with the saw or the tool.
Does trimming an inch off a golf club affect the weight?
But since you’re only trimming a little bit—it will only have a small impact on the overall performance of the club. Like we said earlier, big changes have big side effects.
How to cut a golf club length?
1. Measure the desired new length of club. With the measuring tape, measure the desired length to be cut off. This distance should be taken from the top of the club. Mark the length. Use a permanent marker to mark where the cut should be made.
How to dispose of a golf club grip?
Prepare the work area. Place a towel or clothes underneath your vice grip. Place the club into the vice. Put the club into the vice such that the grip end of the club is pointing at you. Cut off the grip. With a utility knife, carefully make a cut along the grip. Remove the grip and dispose of it in the garbage.
How to lubricate a golf grip?
Hold your finger to the tee-sized hole at the end of grip and spray the solvent into the other end. Shake this around to lubricate the inside of the grip. Put the grip onto the end of shaft. With your finger still holding all the solvent liquid inside the grip, slide the big hole onto the shaft.
How to install grip tape on a golf cart?
1. Apply grip tape to the end of the shaft. Put the new grip along the shaft to see how far down it will extend. This is how far you want the tape to go on each side.
How to get sticky glue off of a golf grip?
Spray with solvent. This will lubricate the tape so you can easily slide the grip over it. This solvent will dry up and become a sticky glue. Spray solvent into the grip. Hold your finger to the tee-sized hole at the end of grip and spray the solvent into the other end.
How long to cool down a hack saw?
Using the hack saw, carefully cut the club where you marked it. Be sure keep fingers away from blade for your safety. Wait 10-15 minutes for shaft to cool off. The metal you just cut will be hot so set it aside for several minutes and allow to cool down. Sand/dull the end of metal that was just cut.
How long does it take to shorten a golf club?
Believe it or not, you can adjust them yourself, without going to a professional. These relatively easy steps will help you shorten a golf club in 45 minutes or less! Steps.
Start with Determining the Length
When changing golf club length [how to change golf club length] for juniors, one of the most important is to identify how short or long it will be. This will depend on the age or height of the user. Once you know the length, use a marker to identify the tip, so you will know where you will cut.
Position the Golf Club
Next, put the golf club in a stable position. Do not hold it while cutting. Instead, it is good to have a vise, which will grip the golf club, so none of your hands will be holding it. This way, it is not only more stable, but you can also be more focused on the cutting part.
Take the Grip Out
The next step is removing grip tape from the golf club [how to remove grip tape from golf club]. This will reveal the main material of the shaft, which also makes it easier to cut. Start by using a utility knife to cut from one end until the other tip. Peel the tape. You might need to exert a bit of force since it is glued in the shaft.
Cut the Golf Club
Next, start cutting the club. You can use a hacksaw to do this. The reason why you should clamp the club instead of holding it is to make the cut more precise while giving your hand the freedom to move. When cutting, use a consistent motion.
Wrap with a Grip Tape
Once you are done cutting the junior’s golf club at the desired length, it is time to wrap it with the new grip tape. This is an important procedure to protect the inner material from wear. More so, it will also make the golf club more comfortable to hold and will optimize its performance.
How does shortening a golf shaft affect swing weight?
Shortening the shaft can make the golf club less flexible. If you are going to shorten a golf club, there are a few things to keep in mind. The more shaft you cut off, the lighter, more stiff, and effectively flatter the club becomes. For every 1/2 inch you remove, you will lose approximately three swingweight points.
How many swingweight points do you lose when you remove 1/2 inch?
For every 1/2 inch you remove, you will lose approximately three swingweight points. You can readjust the swingweight by adding lead tape to the head of the club. Any amount of cutting will slightly stiffen the club. It will probably go unnoticed if you take 1 inch or less off the club.
Why cut down a golf club?
In short, cutting down a club leaves less shaft to offset the weight of the club. And since some players -- including many tour pros with their putters -- still cut down clubs, it's important to know how to offset the potentially negative impact. First, clubs should normally be cut from the butt (or grip) end.
What putter did Sergio Garcia use?
Much was made of Sergio Garcia's change to a TaylorMade belly putter prior to the British Open, but at the Tour Championship the Spaniard used a new putter -- a Guerin Rife Barbados model -- to finish fourth. Last week's putter was heel-shafted; the belly model Garcia used at Carnoustie was center-shafted. ... Mark Calcavecchia was down to one putter in Atlanta (he had used a pair in a previous FedEx Cup event). Calc also went with a new driver (a Ping G10) with the same old-school loft (7.5 degrees) he has used all year. ... So with a $10 million annuity on the line, what did __K.J. Cho__i do? Switch to a set of Nike Ignite irons, a lower-priced club that retails for $400 for a set of eight. Fellow Nike staff player Rory Sabbatini won earlier this year at Colonial using the bargain bats. ... Ernie Els gave fans at East Lake a sneak preview of Odyssey's putter line for 2008 when he used a Black Series i3 model. The putter features a new, firmer face insert. ... Those at last week's PGA Fall Expo in Las Vegas got a look at Nike's driver line for next year, including revised Sumo2 and Sumo drivers. The drivers, which won't be available until February, feature a deep face, and the square-shaped Sumo2 boasts a moment of inertia of 5,900 -- highest allowed by USGA rules.
