- Place a sole tape or black electrical tape on the sole of your club.
- Hit a ball solidly off of a lie board
- Measure how far the center of the sole impact impression is from the center of the scoring lines.
- Have your lie angles bent 1 degree for every from the centerline
How do you show lie on a golf club?
The “Triangle” One way to illustrate lie is to take a club and put it on a table or workbench with the butt end of the club touching a wall. There are numerous positions the club could be positioned, but only one will allow the center of the sole of the club to be making contact with the surface the club is resting on.
Do Your Lie angles fit your golf clubs?
Golfers who use clubs whose lie angles don't fit their body types and/or golf swings are costing themselves strokes. Matching the lie angle of clubs to the specific golfer is one of the goals of a clubfitting session. Lie angles almost always range from the mid-50 degrees (in drivers) to the mid-60 degrees (in short irons).
Why is the Lie of a golf club important?
Because the golf club length of a club may be fixed, it is the lie that controls the length the club is in both the vertical and horizontal positions. Why is this important? Two degrees either direction does not sound like much, but just this little amount altered the height of the club a total of 1. 32” in the vertical and 2.
What is flat lie and up lie in golf clubs?
Flat Lie and Up Lie. Sometimes, in the fitting process, the lie angle is adjusted. Then, if the lie angle is reduced the golf club is “flatter”. Respectively, if the lie angle is increased, the golf club is more “upright”. Such adjustment is expressed in degrees: a number of degrees ( usually 1 … 3 ) flat or up.
What lie should my golf clubs be?
Matching the lie angle of clubs to the specific golfer is one of the goals of a clubfitting session. Lie angles almost always range from the mid-50 degrees (in drivers) to the mid-60 degrees (in short irons). In irons, the range is typically from 59 or 60 degrees to around 64 degrees.
How is lie angle measured on golf irons?
Lie angle is measured from the shaft plane to the horizontal face plane (attitude). Lie is a primary influence on ball direction. Incorrect lie angles force the golfer to adjust or make swing compensations to overcome misdirected ball flight that is, in effect, built into the set of clubs.
How do I know what my lie angle should be?
Lie angle has a Greater impact on short irons than long irons, making lie angle a Major factor of accuracy in short irons and a Minor factor of accuracy in your long irons, fairway woods & driver. Standard lie angles on most irons will be approximate....Determining and Selecting Your Lie Angle.IronsStandard Lie Angle156.0 deg257.0 deg358.0 deg459.0 deg7 more rows
How do you tell if your irons are too upright?
All you need is a marker. Draw a straight line on the back of the golf ball, and have it facing the clubhead. After you make impact the line will appear on the face. If it's pointing towards the toe, then your club is too upright.
What happens if lie angle is too upright?
If your lie angle is too upright, typically meaning that it's closer to 90 degrees than 0 degrees, then that means you will typically hit the ground with your club with the heel side of the sole.
Does upright lie promote a draw?
The upright lie also promotes a left tilting spin axis, which leads to what's generally described as draw spin. An upright lie angle basically gives you a head start, but depending on the severity of the slice conditions the golfer generates, it certainly won't guarantee a draw.
Does 1 degree upright make a difference?
Yes it will make a difference, I play 2 degree upright and +1/2. If your hitting the ball left all the while (I am guessing your right handed) won't be to do with having the lye angle to flat.
What lie angle do pros use?
If you're looking at the lie angle on each club in a set, Sieckmann noted that an elite player might be 1-degree upright in his irons but get gradually flatter when transitioning to the wedges, going to potentially a standard lie angle in the sand wedge and maybe even 1-degree flat in the lob wedge.
What is the angle of the club shaft when you hit the ball?
Lie angle is the angle the club shaft makes with the ground when you HIT the ball and your club head is parallel with the ground.
How to wear golf shoes?
While wearing your golf shoes or street shoes stand on the floor with your normal posture, looking straight ahead, and have your arms hanging in a relaxed position by your sides.
What is the lie angle of a golf club?
The "lie angle" of any golf club is the angle formed between the center of the shaft and the sole, or ground line, of the club when the club is soled in its proper ...
What happens if the lie angle of your golf clubs is ill-suited to you?
When the lie angle of your clubs is wrong for your swing or body type, you can put a great swing on the ball and still have problems with accuracy. Poorly fitting lie angles create pushes and pulls and other mishits.
What does it mean when your divots are deeper on the toe side than the heel side?
If your divots are deeper on the toe side than the heel side (toe down, heel up at impact) or deeper on the heel side than the toe side (toe up, heel down at impact), that's a sign your lie angles might be too flat or too upright.
What is the lie angle on a 9 iron?
Upright lie angle: A lie angle that is higher than the standard lie angle (a 66-degree lie angle on a 9-iron is more upright than the standard 9-iron lie angle of around 64 degrees). You might hear a golfer (or clubfitter) saying things such as, "You need flatter lie angles on your irons," or "I had my irons bent 1-degree upright.".
Why is a proper lie angle important?
Proper Lie Angle Is More Important in Irons Than in Woods. Don't misunderstand: Lie angle is an important factor in all golf clubs, even the putter. But having improperly fit lie angles causes more problems in irons than in the woods.
What is lie angle?
Lie angle is a factor that affects the accuracy of golf shots. Golfers who use clubs whose lie angles don't fit their body types and/or golf swings are costing themselves strokes. Matching the lie angle of clubs to the specific golfer is one of the goals of a clubfitting session.
What is the range of lie angles?
Lie angles almost always range from the mid-50 degrees (in drivers) to the mid-60 degrees (in short irons). In irons, the range is typically from 59 or 60 degrees to around 64 degrees. (Lie angles on putters reach into the 70s.)
What is the lie of a golf club?
The lie of a club is the angle formed by the intersection of the line of the shaft and the line of the ground when the clubhead is resting flat on the ground. That angle number is located between 0 and 90 degree and varies from club to club.
Why is it important to use the correct lies in golf clubs?
Using clubs with the correct lies can prove crucial when working to maximize the chances of hitting the ball straight. Indeed, a club that is too upright for its golfer will see its toe lift from the ground instead of laying flat and as a result balls struck with it will tend to go left of the intended target.
What is the difference between a gold dot and a maroon dot?
At one end of the spectrum is the Gold dot with a 3.75 degree flatter lie and at the other end is the Maroon dot with a 4.5 degree upright lie. Likewise, a shorter golfer will likely be more comfortable using clubs whose lies have been made flatter – less upright – they he would using normal, standard lie clubs.
What happens if you hit a ball with a flat piece of plastic?
Using that tape and hitting balls from a flat piece of plastic will leave an impression on where the sole hit hardest on the ground. If the impression on the tape is made in the center you are using the correct lie. If the impression is close to the heel, you are using clubs that are too flat.
What does "lie" mean in golf?
Lie can also refer to the environment in which the ball finds itself, the ball or shot lie. It can also refer to the number of strokes a player has taken up to a point on a given hole.
Does ping have a color coding system?
For example, a tall golfer who stands tall at address may find it more natural to have clubs whose lofts are a few degree more upright than they normally would. Famously, the club manufacturer Ping has a color coding system for these custom lies.
Nominal Lie Angle
The lie angle of the golf club is the angle formed between the center of the shaft and the sole of the club (ground), when the club is in its proper address position ( grooves parallel to the ground) – see picture below.
Measurement of Lie Angle
In practice it could be a little difficult to measure the lie angle with a protractor. However, it is quite easy to measure it using one of the many available smartphone applications. The application should measure the deviation of the device from the vertical. Just remember to carefully align the grooves on the face parallel to the level / ground.
Flat Lie and Up Lie
Sometimes, in the length fitting process, the lie angle is adjusted. Then, if the lie angle is reduced the golf club is “flatter”. Respectively, if the lie angle is increased, the golf club is more “upright”.
Changes of Lie Angle
Changing the lie angle of a club does not affect its swingweight nor MOI (MOIG). However, such change influences the optimal position of the club when the player adressing the ball. A popular rule indicates that, to maintain the same position of the player, changing the lie angle by 1 degree requires ½ inch change in length.
How to test your golf club's lie angle?
How to test your lie angles. 1) Place a sole tape or black electrical tape on the sole of your club. 2) Hit a ball solidly off of a lie board. 3) Measure how far the center of the sole impact impression is from the center of the scoring lines. 4) Have your lie angles bent 1 degree for every from the centerline.
Why is it important to have a proper lie angle?
Having the proper lie angle will help every golfer with better direction. You could have a great swing with the proper path, but an improper lie angle will tilt the face away from the intended target. Direction is half of the battle, why not have your lie angles checked!
What happens if a golf club lands heal heavy?
If the club lands heal heavy, the toe will close causing shots to the left = hooks. Not only will you sacrifice direction, but with the face plane tilting at impact, the ball will slide across the face causing problems with centeredness.
How much gap between irons?
Most irons have a 4 degree difference between each club from the 5 iron through the sand wedge and around 2 to 3 degrees for the longer irons, this typically equates to a 10 yard gap between each club. If you are having trouble with controlling your distance on solidly struck balls, it may not be your swing! History of iron lofts.
Nominal Lie Angle
- The lie angle of the golf club is the angle formed between the center of the shaft and the sole of the club (ground), when the club is in its proper address position (grooves parallel to the ground) – see picture below.
Measurement of Lie Angle
- In practice it could be a little difficult to measure the lie angle with a protractor. However, it is quite easy to measure it using one of the many available smartphone applications. The application should measure the deviation of the device from the vertical. Just remember to carefully align the grooves on the face parallel to the level / ground. Such a measurement is sho…
Flat Lie and Up Lie
- Sometimes, in the length fitting process, the lie angle is adjusted. Then, if the lie angle is reduced the golf club is “flatter”. Respectively, if the lie angle is increased, the golf club is more “upright”. Such adjustment is expressed in degrees: a number of degrees ( usually 1 … 3 ) flat or up. The picture below shows the example of altering th...
Changes of Lie Angle
- Changing the lie angle of a club does not affect its swingweight nor MOI (MOIG). However, such change influences the optimal position of the club when the player adressing the ball. A popular rule indicates that, to maintain the same position of the player, changing the lie angle by 1 degreerequires ½ inch change in length. Unfortunately, this is only an inaccurate approximation …