First, remove the shaft from the club head by placing the club in a bench vise, and then heat the hosel of the clubhead until the glue melts, making it easy to remove the shaft. If your new shafts are made of steel, rough up the tips with sandpaper, and clean and roughen up the hosel of the clubhead with a wire drill bit.
Full Answer
How to repair&replace a golf club shaft?
How to Repair & Replace a Golf Club Shaft. 1 Step 1. Insert the broken shaft into the vise and remove the shaft by using the heat gun to warm up the hosel and loosen the adhesive that holds the ... 2 Step 2. 3 Step 3. 4 Step 4. 5 Step 5. More items
Can I refinish my golf clubs?
After years of use, golf clubs will get beat up, and in order to make them appear “new,” it is important to remove these signs of use. When I first began learning how to refinish golf clubs, it took me a while to learn how to do this. There aren’t many tutorials out there specific to the technique that is shown in the video below.
How do you remove epoxy from a golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy.
How do you sand a graphite golf shaft?
Graphite shafts may have coating on the end that should be removed with a sharp blade before sanding. Apply epoxy to the inside of the hosel. Make sure the inside of the hosel is completely coated, then coat the tip of the shaft with epoxy. Slide the shaft into the hosel and turn the shaft so that the club head is properly aligned to the shaft.
How do you take a golf club apart?
0:172:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How do you separate a golf head from the shaft?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside.
How do you remove a golf iron head from the shaft?
How To Re-Shaft Your Steel Golf ClubsCarefully clamp the shaft into a vise using a Shaft Vise Clamp. ... When removing steel shafts from clubheads, use a torch to heat the hosel. ... After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head.More items...
How are golf club heads attached to the shaft?
Golf club heads are attached to the golf shaft with epoxy glue. Epoxy is a thermosetting polymer that is a high strength adhesive. Two parts, the resin and the hardener, are mixed together to create a chemical reaction that cures the epoxy to hardness.
Can you reuse shafts?
Reusing graphite iron and wedge shafts. Along the lines of what fupresti said, as long as they're pulled properly you should be able to reuse a graphite shaft indefinitely.
Can you put a new driver head on an old shaft?
The only way to know if we can put your old fitted shaft into a new head it to pull the shaft, weight the head and test the new head with the old shaft. The head may be heavier or lighter, the hosel dimensions may be off which could cause a length issue.
How do you remove a golf driver head shaft?
As you apply heat, grab the clubhead and gently turn it to begin working it out. Avoid cranking with too much force. The shaft could break off inside the hosel. Work the head free carefully and gradually until it comes off.
How do you replace a iron head on a golf club?
2:3122:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the shafts you don't need a shaft puller. Anything like that you can just heat them up andMorePull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
How do you remove graphite shaft without a puller?
0:193:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
What glue is used to attach golf club heads?
A golf club epoxy is an organic compound that is a type of glue that can be used on golf clubs, to attach a shaft to the clubhead. Knowing how to use a golf club epoxy can be beneficial when your clubs need a quick repair job.
How much does it cost to Reshaft a golf club?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
Is it easy to change golf shafts?
Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How to make a golf club with masking tape?
Step 1. Completely cover the head of the club with masking tape to prevent the head from being scratched during the process. Now, place the club in the vise, so that the middle of the shaft is the part being held in the vise. Make sure the club is held securely.
Can you replace a golf club shaft instead of replacing the entire club?
By Tami Fisher. Replacing a golf shaft instead of replacing the entire club can save money. Once in a while, something happens to cause a golf club shaft to splinter or even break. When this happens, the old shaft must be removed and a new one installed in its place.
How to loosen epoxy on golf club shaft?
Move the plastic ferrule from its position next to the club head to a position up the shaft so that it will be out of the way and won't be damaged when you apply heat. Step 3. Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. ...
How to remove epoxy from golf club?
Use a blowtorch or a heat gun to loosen the epoxy that fused the shaft to the club head. Depending on the age of your club, it could take a minute or two before the epoxy begins to liquefy. Once it melts, carefully remove the shaft from the club head, take off the ferrule from the shaft and set it aside. Since the club head can get quite hot, wear ...
How to prepare a club head for a new shaft?
Prepare the hosel of the club head for your new shaft by removing the old epoxy from inside it. The easiest way is to first put the club head into a vise , making sure you don't damage it. Then use a hand drill to carefully remove the debris.
How to remove a broken shaft from a vise?
Step 1. Insert the broken shaft into the vise and remove the shaft by using the heat gun to warm up the hosel and loosen the adhesive that holds the shaft in place. Use medium heat for graphite shafts and higher heat for steel shafts. Once the adhesive has started to melt, pull the broken shaft from the hosel, which is where the shaft meets ...
Can you replace a golf club shaft?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced. Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
Series Navigation
In the world of refinishing, this is by far the most important preliminary step. After years of use, golf clubs will get beat up, and in order to make them appear “new,” it is important to remove these signs of use. When I first began learning how to refinish golf clubs, it took me a while to learn how to do this.
Materials Needed
Protective Gloves (preferably not baggy ones like I’m unfortunately using in the video) and Eye-wear
About the Author: Zach Gollwitzer
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
