How do you remove the engine on a 2001 EZGO golf cart?
There is an easy way to remove the engine on a 2001 EZGO golf cart. Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How to remove EZGO TXT electric motor?
You can use a hammer mildly to slowly tap and pull it off the hold and pull it up. The other issue you may face with the older models of EZGO carts is where the motor could be welded to the body. You will have to use a gas flame to un-weld and remove the motor. How to Remove EZGO TXT Electric Motor?
How do you remove the motor from a golf cart?
Another simpler way to yank the motor out would be to remove the left side rear wheel of the cart out. You can then place the jack (if it is a hydraulic one) beneath the motor. This way, once you have removed all the cables connected to the motor and the bolts, it becomes very easy to remove the motor.
How do you remove the belt from a golf cart starter?
The easiest way is to rotate the clutch towards the cart’s rear to slip off the belt. Remove the belt and keep it aside. Use the 8mm wrench to disconnect the ‘DF’ wire from the starter. Next, use the 10mm socket to remove the ground strap from the starter/generator and remove the part from the cart.
How to change motor on Ezgo cart?
How to change the motor on a Electric EZGO: The first step is to remove the wires connecting the battery pack to ensure that the cart has no power. It is advisable to use protective gloves. Do not use wristwatch, rings or jewelry.
How to remove the engine on a 2001 Ezgo?
Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How to yank a cart motor out?
Another simpler way to yank the motor out would be to remove the left side rear wheel of the cart out. You can then place the jack (if it is a hydraulic one) beneath the motor. This way, once you have removed all the cables connected to the motor and the bolts, it becomes very easy to remove the motor.
How to remove PDS motor?
Here are the steps to remove a PDS motor: You must first put the Run-Tow/Maintenance switch to Tow/Maintenance. Disconnect the wires connecting the battery. Disconnect and remove all the wires and cables connected to the motor. You should then remove the snap ring and the speed sensor from the motor end cover.
Why is it so hard to remove a golf cart motor?
On most occasions, the difficulty in removing the motor from its place in a golf cart is due to the rust that would have developed all around. It won’t come off so easily and you can’t use too much force as it may damage some of the other parts.
Can you pull an EZGO cart up?
For starters, the input shaft could be jammed or broken, making it difficult for you to pull the motor up. You can use a hammer mildly to slowly tap and pull it off the hold and pull it up. The other issue you may face with the older models of EZGO carts is where the motor could be welded to the body.
Operation
As we understand, the motor brake on the EZGO RXV is controlled in an electromagnetic fashion. The circular shoe comes in contact with the brake disk when parking or when braking is needed. The signal to “brake” is controlled via a brake sensor and a throttle sensor on the brake / accelerator pedals respectively.
Failure
Anything mechanical or electrical, including this brake system can be subject to fail. But, brakes are not a system which should be ignored, or neglected due to the risk of serious injury and damage. In our initial inquiry to the customer, we were told that the cart wasn’t driven far after the “burning” smell started.
Do E-Z-Go Golf Carts have titles?
E-Z-Go Golf Carts, unlike vehicles, do not have a title, but they do have serial numbers. If you are buying a golf cart, it is essential to check the serial number to ensure you do not buy a stolen one. Each E-Z-Go Golf cart has a unique serial number that you can use to identify your golf cart.
Where is the E-Z-Go Cart Serial Number
As mentioned above, all E-Z-Go Golf carts have unique serial numbers. These numbers are essential when buying replacement parts for your golf cart. Textron Specialized Vehicles has been building golf carts for a long time, and the serial numbers are placed on different parts of the golf carts.
How do I push my E-Z-Go Golf Cart?
It can be frustrating when your battery is flat and your golf cart will not roll. To push it to the nearest charging or gas station, you need to release the motor brake. Follow these easy steps to do that.
Why does my E-Z-Go golf cart not move
There are several reasons why your cart refuses to move, but you should check the battery before anything else. If the battery is charged, here are some other reasons why your golf cart will not move.
Are all E-Z-Go Golf carts electric?
No, there are both electric and gas-powered E-Z-Go Golf carts available. Bear in mind that there are several models you can drive on the street, but those are all-electric. These electric models run on batteries that you have to charge at least every 24 hours, depending on how much you use them.
How to tell the Assembly year of my E-Z-Go golf cart
The placement of serial numbers is discussed above, and you will find the manufacturer’s number right next to it. The manufacturer’s number consists of one letter and 3 or 4 numbers. The last two numbers indicate the last two digits of the year of assembly.
How to service E-Z-Go Golf Cart
Like all vehicles, E-Z-Go golf carts require regular maintenance to enhance longevity and performance. You should ensure that your golf cart is serviced after every six months of use. That will ensure that you spot problems and repair them early, which will help reduce repair costs. Here are essential guidelines for E-Z-Go golf cart maintenance.
How to Adjust Brakes on EZ-Go Golf Cart?
Today we will discuss how one can adjust the brakes on an EZ-GO golf cart.
Why do you need to adjust the brakes of a golf cart?
Basically, to get safe from any dangerous situation one must adjust the break after sometimes. As time passes and a golf cart gets old the brakes of the golf carts also gets weaken. The break shoe or the brake pad gets worn out or gets loosen. Therefore the brake seems to be not working perfectly.
Adjusting breaks on EZ-GO golf cart
Different manufacturers use different mechanisms to make their golf carts. Some golf carts have their auto adjustable brake mechanism. These types of carts do not need their break to be adjusted.