Golf-FAQ.com

how to disconnect timer on brake lights when you park a 2013 yamaha golf cart

by Felton Feil Published 3 years ago Updated 2 years ago

Place the cart on level ground and chock the wheels. Flip the switch to Tow mode and turn the key to OFF. Keep the batteries hooked and unplug the brake.

Full Answer

How do I turn my brake lights off when parked?

How do I turn my parking brake warning light off? Releasing the brake pedal can turn off the brake light. Some vehicles release the parking brake when shifting out of the park.

Why won't my parking brake lights turn off?

A common cause for car brake lights that won't turn on is a faulty brake light switch. This component can be found beneath your dash attached near the brake pedal. If your lights are disabled, it may be sticking closed or the part has failed.

What is brake light switch?

The brake light switch on your vehicle serves an important safety function. When you press the brake pedal, it supplies power to the signal lights at the back of your vehicle to warn other drivers you have slowed.

Do brake lights stay on with Auto Hold?

Auto Hold keeps the vehicle at a complete stop until you press the accelerator. This is useful in stop-and-go traffic and at traffic lights, so you can relax your foot more comfortably. The rear brake lights remain illuminated when Auto Hold is engaged.

Where is parking brake switch located?

If you have a foot style parking brake, the switch is under the dash mounted to or behind the lever. If you have a hand style parking brake, the switch is mounted under the center console assembly on or below the lever.

Where is a brake light switch located?

In most cars, the brake light switch is installed right above the brake pedal. Inside, it has a one- or two-way electric switch. The most common symptom of a faulty brake light switch is when brake lights don't come on or stay on all the time.

How does a parking brake switch work?

However, the Parking Brake light is actually a multifunctional indicator. It turns on when you pull the parking brake handle to warn you that the brake is engaged when starting the car. When you pull the handle, a cable engages the brake, which is located in the rear of the vehicle.

What are the two switches on my brake pedal?

Cruise control cancel/release switch.

What activates the stop switch?

The stop light switch (Fig. 22) is an air-signaled electrical switch which is turned on any time a brake application is made. The switch is usually connected to a double check valve and can be plumbed anywhere in the application side of the circuit.

How do I turn off auto hold?

0:110:47How to Use the Auto Hold Feature | Hyundai - YouTubeYouTubeStart of suggested clipEnd of suggested clipPress the accelerator pedal to resume driving Auto hold turns off every time you turn off the car toMorePress the accelerator pedal to resume driving Auto hold turns off every time you turn off the car to turn off the auto hold feature without turning off the car press the brake pedal.

How do you turn off the auto hold on a 2021 Ford Explorer?

The Auto Hold (ACTIVE) indicator light illuminates in the information display when the system holds your vehicle stationary. When in active mode, press the brake pedal and the Auto Hold button to switch Auto Hold off.

What is auto hold on Genesis gv80?

0:422:38Electronic Parking Brake & Auto Hold | Genesis G70 | How-To - YouTubeYouTubeStart of suggested clipEnd of suggested clipCompletely by pressing the brake pedal the auto hold indicator turns from white to green auto holdMoreCompletely by pressing the brake pedal the auto hold indicator turns from white to green auto hold will maintain brake pressure to hold the vehicle stationary.

What happens if you don't tighten the brakes on a golf cart?

If this doesn’t happen, the brake cable is either worn out or corroded and needs a replacement.

Why does my parking brake have a latching problem?

The parking brake will have a latching problem if the spring in the pawl that locks it is missing. This spring moves the pawl upwards so that the pedal shaft is engaged. Replacing the spring can set right this problem.

Why does my cart have a faulty motor brake?

The cart has a faulty or improperly installed motor brake if it can be pushed with the key off. Check for this and take the required action. A throttle or controller problem can cause the parking brake to take time to engage. The controller may need replacement or the throttle may need adjustment to close completely.

How to release a Yamaha G29?

You can release a Yamaha G29 parking brake using one of the methods given below. Clean rusty or dirty mechanical connections and linkages between the accelerator and brake linkages. If anything is worn out, replace them.

Why isn't my go pedal releasing?

The Go pedal isn’t releasing all the way as it should because of small objects like rocks or acorns between the pivot housing and the pedal arm. Removing these objects should help achieve engaging.

When to replace brakes on a tow cart?

Replace the brake if it won’t release in Tow mode but the cart rolls when you move the switch from neutral to Tow and push the handle present on the brake. Replace the rod that releases the brake when the throttle gets pushed if the rod is broken at the throttle shaft.

Can a 2008 golf cart brake output be damaged?

If the golf cart is a 2008 or an earlier model cart and has the original motor replaced with an aftermarket one, the controller’s brake output FET could get damaged. More so if the motor has been in use for a long time. You can either change the FET or get it repaired.

What happens if you don't hook up a golf cart?

If you own a 48V or 36V golf cart, and if you do not install or properly hook up a voltage reducer, you will put too much voltage through your lights, resulting in blown lights (and generally voiding all warranties - see blown board image below).

What to do before taking a golf cart out on the street?

The cardinal rule before taking your golf cart out on the street, EVEN WITH the proper lighting/indicators is: CHECK YOUR LOCAL LAWS. Laws and rules are constantly changing, so before taking your golf cart out on the roads, ALWAYS check with your local municipality.

How many volts does a golf cart take?

Even the most basic voltage reducer will do the job, taking 16,18, 36 or 48 volts down to 12. Check out Golf Cart Voltage Reducers for more information.

Why are my lights blown out?

If the voltage reducer was hooked up improperly, the lights may have been blown out due to over-voltage. What you will need to do is check what voltage your cart is running at. Because all electrical accessories run on 12V, and the reducer's job is to take higher voltages down to 12V.

Do you have to engage the parking brake on a gas golf cart?

Yes. If you have a gas golf cart, you will need to engage the parking brake prior to installation. This ensures that your golf cart stays put while you’re working on it. I’ve hooked up the light kit and voltage reducer, but some of the lights are not coming on or came on for a minute and went off.

Should a golf cart be in the TOW position?

Your golf cart should always be in the TOW position when installing electrical accessories such as lights. I want to upgrade my headlights and taillights and already have the holes/cut-outs where the lights should go on my cart.

What to do if golf cart brake light doesn't turn on?

Check the Bulb. This is a no-brainer. If a light does not turn ON, you would check the bulb immediately. In the case of the brake lights in a Club Car golf cart, there are two brake lights at the rear and if both don’t light up, the problem could be elsewhere.

Where is the brake light on a golf cart?

The brake light switch is mounted below the Club Car’s pedal. You will have to remove the floor mat to access it. Most people buying a Club Car do not give much thought to the brake lights. The brake light switch does not form part of the light kit if you have ordered one. This is one reason Club Car golf cart users are surprised when ...

Why do brake lights stay on in a club car?

The other reason for the brake lights staying on in a Club Car is the floor mat blocking the brake pedal from gaining its position back. If it remains pressed, the brake lights could stay ON. You can also confirm if the relay is a timed one, in which case, the brake lights will stay ON for a while before switching OFF.

Why isn't my golf cart brake light working?

The frequently reported reasons for the brake light not working in a Club Car golf cart is either a faulty brake light switch or loose wiring. You have to check these two first before moving on to anything else. A faulty light bulb. Loose or disconnected wires. Faulty brake light switch.

What color wires are used for brake lights?

Also take note of the extra wires coming from the light kit harness. These are usually of four colors – green, red, orange, and blue. Make sure the green and blue wires are connected.

What is the part number for the brake light on a Club Car DS?

If the brake light kit you ordered for your Club Car DS golf cart carries part No. LGT-641, you have the details above. If the kit is different, the wiring diagram may have the following details.

Why aren't my taillights working on my club car?

The reason why the taillights on a Club Car golf cart are not working is because the bulbs are not receiving power. A voltmeter will be required to check if power is available. The other method is to use a 12V jumper on the bulbs. If they light up, then there is no issue with the taillights.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9