Hook up the plastic tubing to the quick connects by just pushing them on them. Then run them downwards toward ground and out the side of the car. Now hook a garden hose to one of the tubes and duck tape it to seal it up.
Full Answer
How do I connect my quick connect heater hose?
1:0116:06How to: Replace Heater Hose Quick Connect Adapters 2000 ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipOne. Now that tool is supposed to go on the hose. Here. And slide up into the quick connect. AndMoreOne. Now that tool is supposed to go on the hose. Here. And slide up into the quick connect. And release it so that you can pull the hoses apart.
How do you use the quick disconnect tool on a heater hose?
0:162:01Chevy Truck Heater Hose Quick Disconnect Removal DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo you come in from underneath. And you put your tool on the line. And then you pop it in there.MoreSo you come in from underneath. And you put your tool on the line. And then you pop it in there. There you go top. This is what the connector looks like. And your tool ends up going in there.
How do you remove a heater core hose connector?
1:262:39How to remove a heater hose quick connect on a GM - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere you go is clip then pull it out. And there you go.MoreThere you go is clip then pull it out. And there you go.
What connects to the heater core?
Heater hoses are smaller hoses that are attached to the heater core, which is located under the dashboard, to supply warmth to passengers in the cabin.
How do I remove quick connect from my car?
3:0412:37How to Disconnect Common Quick Connect Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen you push in this case I'm pushing down because I'm pushing away from the position. And then IMoreWhen you push in this case I'm pushing down because I'm pushing away from the position. And then I push this out. And then I can release the line.
How do I get rid of quick connect?
1:373:07Install or Remove Quick Connect Fittings - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe press in both the hose and the collar. We hold the collar and pull to remove the hose. If we needMoreWe press in both the hose and the collar. We hold the collar and pull to remove the hose. If we need to reinstall this hose. We want to cut past where our notches are from where the collar.
How do you change a heater core hose?
Loosen hose clamps and carefully remove the leaking hose. Install the new hose, install new hose clamps, and refill cooling system with recommended anti-freeze / water mixture at 50/50 concentration. Pressure test cooling system again to check for any other leaks. Repair any new leaks.
How do you remove a coolant hose connector?
10:0921:56How to Replace Coolant Hose Connector 01-05 BMW 325XiYouTubeStart of suggested clipEnd of suggested clipPull it up just like that you're gonna have some more coolant come out slide it up slide it up I canMorePull it up just like that you're gonna have some more coolant come out slide it up slide it up I can disconnect the connector right here push down on the tab. Pull it out like that.
How do you remove a plastic hose connector?
0:080:56How to remove a Hoselink Hose End Connector from your Hose - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace the fitting into boiling. Water this will help soften the hose after 45 seconds put theMorePlace the fitting into boiling. Water this will help soften the hose after 45 seconds put the fitting in between your feet like this and pull the hose in an upward motion.
How do I know which heater core hose is Inlet?
0:081:01Locating an Inlet Heater Hose - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo the top of the engine you can see you can follow it around to the top of the engine. That is theMoreTo the top of the engine you can see you can follow it around to the top of the engine. That is the inlet hose we're going to make our connection for our flush kit.
What does the heater hose connect to?
A heater hose is a rubber hose used in automobiles, and it transports hot coolant to the heater core. The heater hose connects to the water pump and the heater core, which is located next to the firewall on most vehicles.
Does it matter which hose goes where on a heater core?
0:372:29Which Heater Hose goes Where? - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo this way that warm water will go in the bottom push. Out any air. And then go through the top.MoreSo this way that warm water will go in the bottom push. Out any air. And then go through the top.
How to fix heater core?
An Autoparts store would have a repair manual for your car. In The Meantime: 1. Disconnect the heater hoses, at the firewall in the engine compartment. 2. Connect the two hoses together using a piece of tubing and a couple of hose clamps. ( This will bypass the heater core, until you can get it fixed.)
What happens if the copper hose breaks free from the heater core?
If the copper/metal hose broke free from the heater core, the heater core will need to be removed and replaced. let me know what size engine and I can send you the removal procedures. Big job!!