how to get tape off golf club shaft

1. Heat the golf club you plan to remove the tape from with a heat gun. It should take approximately 10 minutes to heat the shaft.
2. Rub down the tape with mineral spirits. Peel the tape off of the shaft. ...
3. Wipe the shaft with acetone after you have removed the tape. This will help further clean the shaft, as well as remove the mineral spirit residue.
4. Repeat the process for each graphite golf shaft requiring tape removal. ...
5. Set the club on a workbench or other level surface so the club face is perpendicular to the ground. ...

How do you remove tape from a golf club?

Heat the golf club you plan to remove the tape from with a heat gun. It should take approximately 10 minutes to heat the shaft. Focus the heat gun on the grip area of the shaft where the tape is located. Rub down the tape with mineral spirits. Peel the tape off of the shaft.

How do you remove mineral spirit tape from a shaft?

You can use a knife to lightly scrape the tape off of the shaft if it does not peel off easily by hand. Wipe the shaft with acetone after you have removed the tape. This will help further clean the shaft, as well as remove the mineral spirit residue.

How do you remove tape from a screwdriver shaft?

Once the tape is nice and slippery the tool will cut through the tape like it's butter. Once you've scrapped most of the tape off, pour mineral spirits on shaft and wipe excess adhesive off. 2. Dry peeling the tape. I actually like this method more.

Can you replace a grip on a graphite shaft?

If you choose to do the grip replacement yourself, a common problem that arises is removing the grip tape from graphite shafts during the replacement process. Unlike steel shafted clubs, graphite shafts can be damaged much easier during the tape removal process and require special attention.

How do you remove old tape from regripping golf clubs?

How to Remove Golf Grip TapeStep 1: Prepare Supplies. To do this properly, you are going to need a few supplies. ... Step 2: Remove Old Grip. The first part of this process starts with removing the old grip. ... Step 3: Heat Up Tape Residue. ... Step 4: Wipe Down with Mineral Spirits. ... Step 5: Dry/Check for Tackiness. ... Step 6: Regrip.

What can I use for golf tape solvent?

Mineral spirits, denatured alcohol, acetone, nail polish remover or charcoal lighter fluid, all provide adequate deactivation of grip tape to install new grips. They also evaporate relatively quickly to allow the grip tape to bond to the grip in a relatively short amount of time, often less than an hour.

How do you remove golf Club extensions?

3:5011:02How to ADD Extensions To Golf Clubs - Start to Finish! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd pick it off but I like to do is I like to put it in the vise. Get my torch and heat it. Up. ItMoreAnd pick it off but I like to do is I like to put it in the vise. Get my torch and heat it. Up. It only takes about five to seven seconds of heat. To loosen it up. My box cutter.

Can I use rubbing alcohol as grip solvent?

Step 2: Get rid of old grip tape It's sometimes the most tedious and least fun part of the re-gripping process, but Goo-Gone, Goof-Off, rubbing alcohol, etc., all work to help speed up the process.

What type of solvent is golf grip solvent?

Some golfers use paint thinner, mineral spirits, acetone, lighter fluid or even camping fuel as a grip solvent. Many of these substitutes are not only flammable but also emit noxious fumes. Odorless versions of paint thinner and camping fuel are available on the market.

How do you remove steel shaft extensions?

1:172:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just lock it off like. This. Now once you're done just don't lay it down the best thing to doMoreAnd just lock it off like. This. Now once you're done just don't lay it down the best thing to do would be to take a wire brush or a drill with sandpaper on it and remove the excess epoxy.

How do you remove stickers from graphite shafts?

2:505:54How to get stickers & glue off you golf shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we're gonna get rid of that this is all you need hot water goo gun and a dry piece of paper towelMoreSo we're gonna get rid of that this is all you need hot water goo gun and a dry piece of paper towel you don't want to use the wet light because you want to rub the glue gun on the goop.

How do you remove epoxy from golf shafts?

Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the epoxy that bonds the shaft to the hosel and make removal easier. If you are working with graphite shafts, use a heat gun, not a torch. Wear goggles and protective gloves.

What tool to use to cut through tape?

Tool: specialty scrapper, knife or putty knife/wall paper scraper. I've found that it works best if you lubricate the tape with mineral spirits or what ever lubricant you are using. Once the tape is nice and slippery the tool will cut through the tape like it's butter.

Does a taped shaft need to be cleaned?

Shaft is perfectly clean with no residue of any kind. Doesn't matter if it's new tape / old tape / factory tape, or even multiple layers of tape. Hold it over a garbage during the process and there's no clean up to do afterwards.

Is a scraper good for tape?

The scraper is good for stubborn tape but I feel like it leaves more residue and what I like to call "dingleberrys" behind after scraping. quote] The "dingleberries" are not an issue if you quickly spray a little solvent and scrape again briefly. Wipe with a paper towel and it's perfectly clean. Quote.

tical

Peanut Butter also works on removing gum from your dress pants, jeans, clothing etc.

keith723

Goo gone has worked the best for me after you tear the sticker off--the goo gone will get the rest of the sticky stuff off and then just wash with soap and water to get the greasy goo gone all the way off My wife already thinks I'm a crazed golf nut...

BigPete

Did you say "Adams" peanut butter? Now that's some forward thinking cross-polinational maketing strategy. (Did it come in a box rather than the traditional jar?)

Tupperwolf

Of all the many products on the market guaranteed to safely remove sticker glue, you come up with PEANUT BUTTER?

alectra82

I recently purchased some clubs and tried removing stickers on the shafts, which left glue/sticky residue on the shaft. I searched online and found several methods of removing the glue. I heard nail polish remover and paint thinner. I really didn't want to try either of those on my graphite shafts and wedge/steel shafts.

RJRJRJ

I use goo gone. It smells good and doesnt damage anything. I think its like $4 from home depot so its cheap too.