
Installing the Boost Gauge Wiring 1. At the bottom of your knee panels beneath the steering wheel, there will be 3 Torx screws, I believe size 20 or 25. Remove those three screws, and the plastic panel above the pedals can now be removed.
Full Answer
How to secure the boost gauge to the housing?
The biggest time killer for me was screwing the clip into the back of the boost gauge to secure it to the housing. Depending on the brand of the boost gauge you may or may not have to use the supplied clip; some boost gauges are a little fatter and secure themselves tightly in the pod.
What is the best boost gauge for turbo cars?
This is a great mod for any turbo car. It's cheap, easy, it looks good, and, most important, it helps you monitor your boost. For a nice stock look, I would recommend Autometer Cobalt boost gauges, I personally think that they look the best, but they can be expensive. For a cheap but still quality gauge, I would recommend VDO.
What size boost gauge do I need for my pods?
The pods are made for 2 1/16th inch boost gauge, so when buying your gauge keep the size in mind. In this DIY, I will be primarily focusing on installing the wires correctly.
Do I have to use the supplied boost gauge clip?
Depending on the brand of the boost gauge you may or may not have to use the supplied clip; some boost gauges are a little fatter and secure themselves tightly in the pod. Also, before you get it all hooked up in the pod, c heck the light to make sure it illuminates.

How do you hook up a boost gauge on a mk4 TDI?
2:098:25Boost Gauge Install on a mk4 - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo the fuel pressure regulator I split in there and then I just piped it off with a tee fitting. AndMoreTo the fuel pressure regulator I split in there and then I just piped it off with a tee fitting. And it goes around here.
How do you hook up a diesel boost gauge?
1:2610:02GlowShift | How To Install A Diesel Boost Gauge - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce your factory bolt is the move simply screw in the boost bolt with the compression fittingMoreOnce your factory bolt is the move simply screw in the boost bolt with the compression fitting attached. You want to tighten the boost bowl to a hundred and twenty inch paddles.
Where do you connect a boost gauge?
4:177:49Boost Gauge Install - YouTubeYouTubeStart of suggested clipEnd of suggested clipSource close to the manifold.MoreSource close to the manifold.
How do you install a 1.8 t boost gauge?
0:3910:35How to Easily Install a Boost Gauge! (Golf GTI Mk4) - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I'll show you now but today I just said we are installing a boost gauge onto a mark for 1.8 turboMoreSo I'll show you now but today I just said we are installing a boost gauge onto a mark for 1.8 turbo. So I'll show you what I've done so far. So to start this off go typical of box out.
Can I use a petrol boost gauge on a diesel?
A boost gauge (boost-only) should only ever be considered on either a diesel application, as they do not produce vacuum and spend much time in boost, or on a blown race car that spends most of its life a quarter mile at a time at wide open throttle.
What does a diesel boost gauge do?
A boost gauge is an instrument that is used to show the amount of pressure a turbo charger or super charger is producing. Typically, a turbo or super charger system is designed to give the maximum benefit at a particular amount of boost pressure.
Do I need a boost gauge?
If you use a turbo or supercharger to increase your engine's efficiency, then a boost gauge is a must-have accessory. It monitors the pressure flowing into the combustion chamber. Low pressure is inefficient, while high pressure can blow the engine.
How does a vacuum boost gauge work?
The tube has a specific amount of inert gas trapped within it. Additionally, this tube runs from the gauge to the manifold, where the air flow passes. The pressure of the passing air places pressure on the tube. The tube's internal pressure raises, and a deflection in the gauge is accomplished.
How do you hook up gauges in a car?
4:249:00ULTIMATE Gauge Install Guide (ANY CAR) - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo we can strip the ends. And add the terminals. On i then found the grommet on the passenger sideMoreSo we can strip the ends. And add the terminals. On i then found the grommet on the passenger side and fed the wires through there and then pulled them through from the inside.
How do you install a boost gauge on an Audi a4 b6?
6:4711:04ECS Tuning: Audi B6 A4 1.8T Vent Pod Boost Gauge DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd the gauge opening is facing the driver align the small pins with the index on the vent assembly.MoreAnd the gauge opening is facing the driver align the small pins with the index on the vent assembly. And snap the pot into place before installing the face of the vent reconnect.
What is a boost gauge?
Installing a Boost Gauge. This is a great mod for any turbo car. It's cheap, easy, it looks good, and, most important, it helps you monitor your boost. For a nice stock look, I would recommend Autometer Cobalt boost gauges, I personally think that they look the best, but they can be expensive. For a cheap but still quality gauge, I would recommend ...
Where is the vacuum line on an Audi?
It is located on the right side of the fuel rail (toward s the windshield if you have an Audi), and unlike in the picture, the hose will be black braided fabric.
Can you change the gauge on a 194 light?
Just make sure the gauge you choose allows you to change the light so you're not stuck with a lime-green light that doesn't match anything in your car. As long as you can change the bulb, you can use any color LED size 194 light you would like. You will also want a gauge pod for your gauge to sit in.
