A)Using 10x70mm bolts and Rubber Spacers from Pack 2, attach the Arm Reststo the rear of the Seat Frameand Seat Back Support Bar. B)Attach Armreststo the front of Seat Frame using the 10x45mm Countersunk bolts from Pack 2. Acorn nuts go on outside of cart.
Full Answer
How do I install my EZGO golf cart?
This installation will require the removal of the golf cart’s roof and rear roof struts. We will also need to remove the seat back and upright struts the seat back is mounted on. Next remove the rear motor access panel (requires small torx bit.) After step 1, the image on the left shows what your Ezgo golf cart should look like.
How to install a battery rack on a golf cart?
At this stage, the battery rack is so that the slotted holes align with existing mounting holes in golf cart frame. You will next need to install a 5/16″ or 3/8″ bolt into the front tabs and secure with washers and lock nuts. Secure the battery tray hangers to the golf cart frame and connect them to the battery tray itself.
How do I remove the EZGO battery tray?
Once out, take your flat head screw driver or pry bar to separate the two pieces of angle iron that make up the body panel support. Then bend down the original battery tray hangers to complete the removal of the old Ezgo tray. See images below.
How do you remove a battery tray from a golf cart?
Under the floor mat you will find two Torx screws on the opposite sides of the golf cart. These screws hold the battery rack in place. Remove screws and then maneuver the tray out from under the body panel. ( This is why we usually cut the old one out with a plasma cutter – Time saver step! ) 3.)
How do you put the back seat on a golf cart?
4:0511:23Installing A Steeleng Rear Seat Kit On My Wifes Club Car Precedent CartYouTubeStart of suggested clipEnd of suggested clipThe holes in the plastic. We're not lined up with the holes in the aluminum. So. I had to just drillMoreThe holes in the plastic. We're not lined up with the holes in the aluminum. So. I had to just drill the plastic out to open hole up a little bit so I could mount the brackets.
How do you put the back seat in a EZ GO TXT?
2:027:24Modz Flip4 EZGO TXT Rear Seat Kit Installation How-To - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut it to the inside hole on each side. And our bolt washer. And washer and nut on the backside. NowMorePut it to the inside hole on each side. And our bolt washer. And washer and nut on the backside. Now we'll do the same thing to the other side.
How do you put the back seat in a ezgo RXV golf cart?
4:479:26EZGO RXV GTW Rear Flip Seat Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure you connect it to the slot. Once all the bolts are in position go ahead and tighten allMoreMake sure you connect it to the slot. Once all the bolts are in position go ahead and tighten all the bolts start from the trees. Then moving to the two in the back of the flip seat.
How hard is it to put a back seat on a golf cart?
6:007:17How to Install Golf Cart Rear Flip Seat for EZGO TXT - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp you can pull it out we're almost through then our next step is going to be using those two holesMoreUp you can pull it out we're almost through then our next step is going to be using those two holes to line up with these two we will put this piece on here.
Which ezgo do I have?
The serial number and manufacturer's number for these EZGO golf cart models can be found on a plate located under the glove box on the passenger's side of the vehicle. The serial number is either six or seven numbers and does not indicate the model year. The manufacturer's number does reflect the model year.
How do you remove a golf cart hub?
0:202:18How To Quickly Replace A Stripped Golf Cart Hub - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you're going to want to do is you want to remove the cotter pin this case I used use pryMoreSo what you're going to want to do is you want to remove the cotter pin this case I used use pry some pliers. And a flat tip screwdriver. And you're going to loosen the castle. Nut.
How do you put a rear arm rest on a golf cart?
0:442:24Universal Arm Rest | How to Install Video | Madjax® Golf Cart AccessoryYouTubeStart of suggested clipEnd of suggested clipAnd we want our first hole to the right of the flat spot right before the contour of our curves inMoreAnd we want our first hole to the right of the flat spot right before the contour of our curves in the armrest mark that hole with your PIN mark your second hole with your PIN.
How do you turn a 2 seater golf cart into a 4 seater?
You should connect the footrest brackets and footrest before the seat back brackets and armrests. Add the seat bottom cushion, lean-back cushion, and lean-back brackets. And there you go! That's how you can convert a two-seat golf cart into one with four seats.
How do you install snubber on a club car?
2:454:341984 - PRESENT CLUB CAR TRANSMISSION MOUNT ...YouTubeStart of suggested clipEnd of suggested clipSlide the new snubber onto the bracket just like that. And we'll reinstall. All right let's just goMoreSlide the new snubber onto the bracket just like that. And we'll reinstall. All right let's just go ahead and install the. Nuts. Just like that. And we'll get those torqued. Down. Play any time.
How to attach battery tray to golf cart?
Pry the two angle iron cross members apart just enough to slide the rear battery tray hangers into position.
Is the battery tray on an Ezgo golf cart rusting?
Have you purchased an older model Ezgo golf cart recently? Are you discovering upon battery replacement that the factory battery bracket is rusting out? Ezgo battery tray is often a rusted mess if it is a decade or older. From the factory, the Ezgo battery rack is made of a lower quality steel. To replace it follow our instructions for Ezgo Cart Battery Tray Installation.
How to attach a lean back support to a motor?
Attach Lean Back Supportsto the outside of and rear struts to the inside of the Main Bracketsusing retained strut hardware from Step 1. Tighten hardware. Reattach the motor cover using hardware retained from Step 1. Remove outermost bolts in bagwell and attach Bagwell Bracketusing same hardware. Tighten hardware.
Where is the arm rest on a car?
Arm Reststo the rear of the Seat Frameand Seat Back Support Bar.