How to adjust the carburetor on an EZGO gas cart?
EZGO Gas Cart Carburetor Adjustment 1 Adjust the idle jet pilot screw on the carburetor. This can be done by doing a 1/4 turn of the screw. 2 Do a valve clearance adjustment starting with the cold valve. ... 3 If the locknuts in the MCI engine have a size of 9mm and square heads, you’ll need a pair of needle-nose pliers and a 9mm socket.
How to adjust a carburetor on a golf cart?
The way to adjust the carburetor on a golf cart will depend on the model of golf cart. In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor. The engine shows a reduced performance such as a reduction in fuel efficiency or power and sluggish acceleration.
How do I tune-up my E-Z-Go gasoline engine?
These are the easy steps to perform a basic tune-up on your E-Z-Go gasoline engine using a minimum of tools and an optional tune-up kit. As always, we begin with the three basics…Air, fuel, spark. Unsure of your year and model?
How do you remove a Robin 295 from a golf cart?
The expert advice on the easy way of removing the Robin 295 engine from a golf cart (a 1997 EZGO TXT or any other model) is as follows: Disconnect all the electrical, fuel and air supply lines. Then remove the belts, exhaust and the choke cable.
How to adjust carburetor on golf cart?
In most cases, you’ll need to adjust the jet pilot screw, perform a valve clearance adjustment and then clean the carburetor.
How to replace carburetor float?
Remove the carburetor and turn it upside down. Remove the nut that is used to secure the bowl on. Check the float for a puncture as this prevents the activation of the fuel cut-off needle valve. Replace the float if there is a puncture. Check for dirt accumulation in the needle valve.
Why does my carburetor flood on my golf cart?
The reason why a carburetor floods on a golf cart is usually due to a faulty fuel pump. The pump must be repaired or replaced accordingly. Seek professional assistance if required. This is usually due to the proximity of the fuel line to an exhaust manifold, a radiator hose or a heat source.
How to cool down a golf cart?
Procedure. Turn off the golf cart engine and allow it to cool for a couple of hours before you start working. This cooling down prevents damage to the cart and injury to yourself when you’re at work. Turn off the fuel-supply valve and remove the fuel line to prevent flooding of the fuel and other complications.
Where is the main jet on a 2 cycle engine?
The main jet in the carburetor diagram of a 4-cycle engine is located below the carburetor while the pilot jet is present on top of it. The needle valve and float pin are also housed under the carburetor.
Which is more powerful, carb or EFI?
The carb model is more powerful as well as starts and goes faster when compared to the EFI. The EFI experiences delay to start moving when the pedal is pressed.
How to remove cable from carburetor?
Remove the cable from the carburetor and cover its sheath opening using duct tape. To do this, make a small funnel with the tape and ensure that the wire sticks out from its middle. Loosen the nut that fixes the cable on to the mount housed on the motor just before its entry into the carburetor.
What is a golf cart?
Golf carts are also known as golf cars. The term "cart", in its purest sense, refers to a vehicle that does not travel under its own power. Golf cars, however, are most commonly referred to as golf... link to Club Car DS Wiring Diagrams 1981 To 2002.
Where is the second filter on a carburetor?
Return the filter to the gas line and secure it with the clamps. Sometimes there is a second filter located underneath the carburetor facing the front of the cart. Check to see if you have one and make sure it is also clear of deposits.
How to remove fuel filter from fuel pump?
To remove the filter, disconnect the hose from the fuel pump by using a pair of pliers to squeeze the clamp ends together and sliding the expanded clamp further down the line. Raise the hose up and allow any excess fuel to drain back into the fuel tank.
How to change motor on Ezgo cart?
How to change the motor on a Electric EZGO: The first step is to remove the wires connecting the battery pack to ensure that the cart has no power. It is advisable to use protective gloves. Do not use wristwatch, rings or jewelry.
How to remove the engine on a 2001 Ezgo?
Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How to yank a cart motor out?
Another simpler way to yank the motor out would be to remove the left side rear wheel of the cart out. You can then place the jack (if it is a hydraulic one) beneath the motor. This way, once you have removed all the cables connected to the motor and the bolts, it becomes very easy to remove the motor.
Why is it so hard to remove a golf cart motor?
On most occasions, the difficulty in removing the motor from its place in a golf cart is due to the rust that would have developed all around. It won’t come off so easily and you can’t use too much force as it may damage some of the other parts.
Can you pull an EZGO cart up?
For starters, the input shaft could be jammed or broken, making it difficult for you to pull the motor up. You can use a hammer mildly to slowly tap and pull it off the hold and pull it up. The other issue you may face with the older models of EZGO carts is where the motor could be welded to the body.