Locate the speed sensor on the golf cart. This is usually present behind the rear tire of the golf cart on the driver’s side. Remove the snap ring or circlip with two clips that hold the speed sensor in place, using a pair of pliers.
Full Answer
Where is the throttle sensor on an EZGO golf cart?
The inductive throttle sensor in an EZGO is a part of the electrical system of the golf cart and is connected through a wiring harness to the direction selector. It functions inside the pedal box.
How to use an EZGO golf cart?
Activate the Run/Tow switch of the EZGO golf cart by setting this switch in the Run position. Try to push the cart slowly forward. If you hear a rapid beeping sound and resistance to the pushing action because of the regenerative braking action, your EZGO golf cart has a good speed sensor and is communicating with the speed controller.
How to remove speed sensor from EZGO TXT PDS golf cart?
The speed sensor of an EZGO TXT PDS golf cart can be removed easily by following a few simple steps as given below. Locate the speed sensor on the golf cart. This is usually present behind the rear tire of the golf cart on the driver’s side. Remove the snap ring or circlip with two clips that hold the speed sensor in place, using a pair of pliers.
Where is the speed sensor located on a golf cart?
This is usually present behind the rear tire of the golf cart on the driver’s side. Remove the snap ring or circlip with two clips that hold the speed sensor in place, using a pair of pliers. Pull the speed sensor from its place.
How do you change the inductive throttle sensor on a EZ Go golf cart?
Replacing the Inductive Throttle Sensor Lift up the floor mat and look for a cutout on the floorboard. Remove the cutout and take off the screws from the pedal box. Find the inductive throttle sensor and remove its connecting screws. Place a new sensor in its place and replace everything you removed.
Where is the EZGO speed sensor located?
Typically, the speed sensor can be found on the backside of the motor. When removing the speed sensor, unplug all the cables that are on the backside of the motor. To do this, use a socket to take off the connector pigtail. Then, remove its plastic housing over the sensor.
Where is the reset button on a ezgo golf cart?
Locate the motor Remove the panel so the electric motor is visible. Electric motors usually include reset buttons that can perform similar to circuit breakers. Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.
How do I fix my EZGO speed controller?
Here are 5 steps you should follow for a DIY fix to your golf cart's speed controller.Flip the maintenance switch. ... Reset the battery cable. ... Check your connections. ... Test the solenoid. ... Check your controller's power output.
Where is the speed sensor located on a golf cart?
The speed sensor in a Club Car Precedent golf cart is located on the back of the motor. To remove the sensor, unplug the cables behind the motor. You can use a 5/16-inch socket to remove the pigtail connector and pop off the plastic housing that encases the speed sensor.
How does a speed sensor work on a golf cart?
Magnetic Style Many golf cart motor speed sensors employ an electromagnetic power to “read” the motor rpm. Generally, there is a magnet present in the closed end of the motor as well as the sensor itself which reads how the magnet is reacting with the magnetic field inside the motor.
Where is the reset button on the motor of a electric golf cart?
First, you'll want to reset your motor. It should have a small reset button (Usually it will be red) located near the main battery supply. Hit the reset button and then put the cover back on the motor. The next step would be to recharge your cart and try turning it on again. If it starts up then you're in luck!
How do I know if my EZGO controller is bad?
Press the accelerator and watch to see if the voltage increases. It should increase from a reading of 0 to the full voltage of the battery. If the motor is not turning, the problem may be in the directional switch or motor. If there is no voltage, the controller is bad and must be replaced.
How do you troubleshoot an electric EZGO golf cart?
Things to Keep in Mind Before TroubleshootingEZGO golf cart batteries aren't perfect right away.Sticky accelerators are perfectly normal and can be fixed easily.Keep your cart stable.Make sure your charging wall socket isn't faulty.Keep your tire pressure stable.Troubleshooting the speed controller.
How do I test my golf cart speed controller?
How to Test a Club Car Golf Cart Speed Controller? The simplest test to ascertain your golf cart controller's performance is to to watch whether it runs when the batteries are fully charged with a slight push of the pedal. If you hear a distinct clicking noise, then your golf cart is running correctly.
Why is my ezgo golf cart so slow?
A EZGO RXV and TXT golf cart can run slow because of a faulty speed sensor, low battery charge and insufficient levels of water in the battery. A problem with the speed sensor. A faulty speed magnet. One or more batteries could are weak and don't have sufficient charge or the water level could be low.
How can I test my speed controller?
0:395:30Testing controller for blown mosfetts - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe start by connecting one of the probe to the ground wire of the controller. And you take theMoreWe start by connecting one of the probe to the ground wire of the controller. And you take the positive probe.