Why is my EZGO golf cart losing top speed?
A loose drive belt can result in your EZGO Golf Cart to lose top speed and underperform. If the drive belt is the right model but it seems to be too loose then it could be because there is something stuck in the clutch or there is some damage in the clutch. In this case you’ll need to call a certified technician to inspect your golf cart.
What does the drive belt do on a golf cart?
The drive belt on a golf cart connects the two clutches (the drive clutch and the driven clutch) and distributes the power from the engine to the rear wheels. There can be a number of issues that can happen to a drive belt which you should be aware of.
How do you replace the drive belt on a Ford Ranger?
Take note of how the existing belt has been adjusted to the clutches and then remove it. Slide in the new belt to the primary clutch and pull it all the way around the secondary clutch the same way the old belt was adjusted. Roll the secondary clutch to make sure the drive belt is secured and is in its proper position.
How do I know if my drive belt is too tight?
To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger. If it deflects less than 1.5” it’s too tight.
How do you change a belt on a EZGO golf cart?
1:195:57Changing the Drive Belt and Starter Generator Belt 2008 EZGO TXTYouTubeStart of suggested clipEnd of suggested clipDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back.MoreDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back. Until it pops off that rear driven clutch and then take it right out.
How do you install a drive belt?
1:032:15How to - Replacing a Drive Belt // Supercheap Auto - YouTubeYouTubeStart of suggested clipEnd of suggested clipCheck it with a tension gauge. With automatic tension systems gently allow this to apply the tensionMoreCheck it with a tension gauge. With automatic tension systems gently allow this to apply the tension to the belt. Start the engine and observe.
How tight should a golf cart drive belt be?
The drive belt should not be too tight. If it's too tight it can risk wearing off faster and it's also harder to shift gears. To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger.
How do you change the drive belt on a?
0:582:22How to Replace a Serpentine Belt in Your Car (Fan Belt) - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou just hook it up here to the bolt that loosens attention her pulley and then pull on it. As youMoreYou just hook it up here to the bolt that loosens attention her pulley and then pull on it. As you pull it down the belt gets loose. Then you can just take it off. And out comes the old fan belt.
Is it easy to replace a drive belt?
Serpentine belt replacement is easy because today's automatic drive belt tensioners eliminate the need to loosen bolts or pry components into position for retensioning. Just rotate the tensioner, remove the old belt and install a new one.
How long does it take to replace a drive belt?
It can take anything from 15 minutes to an hour (two at the most) to repair or replace a bad serpentine belt with a new belt.
How does a drive belt work on a golf cart?
The drive belt is one of the most important belts on your EZGO golf cart. It helps to translate engine power into different gears and makes it possible to shift your cart, giving it the get up and go it needs to run. However, there are times when this belt may be loose or damaged and you may want to tighten it.
Can you adjust a golf cart clutch?
If you are unsure about removing the drive belt or the clutch, then you can adjust it. Just take out the belt and wound it again with the secondary clutch according to the requirements, and your problem should be fixed.
How do you measure a golf cart belt?
0:002:04How to measure for a go-kart drive belt. - YouTubeYouTubeStart of suggested clipEnd of suggested clipCover. Now the first measurement we're going to take on this is we're going to measure from theMoreCover. Now the first measurement we're going to take on this is we're going to measure from the centerline of the crankshaft. To the centerline of the jack shaft.
How do you change a belt?
3:406:26How to Replace a Serpentine Belt - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust enough so that we can get our pin out pull it towards the front of the vehicle remove your pinMoreJust enough so that we can get our pin out pull it towards the front of the vehicle remove your pin slowly. Let the tension come out remove your ratchet. And you have installed the belt.
How do you release a tensioner?
0:393:48How to Remove Car/Truck Tensioner Pulley -Up Close - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then you normally you want to pull up on it like that and when you pull up on it that's actuallyMoreAnd then you normally you want to pull up on it like that and when you pull up on it that's actually going to release the tension.
Are drive belts Universal?
Today, there's one belt to run them all—well, for the majority of vehicles. It's called the serpentine belt. Some rides may have an additional belt to run select accessories, but the serpentine does the bulk of the work.