Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
Full Answer
Why is my EZGO golf cart losing top speed?
A loose drive belt can result in your EZGO Golf Cart to lose top speed and underperform. If the drive belt is the right model but it seems to be too loose then it could be because there is something stuck in the clutch or there is some damage in the clutch. In this case you’ll need to call a certified technician to inspect your golf cart.
How do you replace the belt on a golf cart?
Raise the golf cart engine cover, to access the drive belt inside the engine compartment. The drive belt is plainly visible. Loosen the drive belt tension bolt, with the open end wrench, on the front pulley.
What does the drive belt do on a golf cart?
The drive belt on a golf cart connects the two clutches (the drive clutch and the driven clutch) and distributes the power from the engine to the rear wheels. There can be a number of issues that can happen to a drive belt which you should be aware of.
How do you replace the drive belt on a Ford Ranger?
Take note of how the existing belt has been adjusted to the clutches and then remove it. Slide in the new belt to the primary clutch and pull it all the way around the secondary clutch the same way the old belt was adjusted. Roll the secondary clutch to make sure the drive belt is secured and is in its proper position.
How do you change a belt on a Easy Go golf cart?
1:195:57Changing the Drive Belt and Starter Generator Belt 2008 EZGO TXTYouTubeStart of suggested clipEnd of suggested clipDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back.MoreDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back. Until it pops off that rear driven clutch and then take it right out.
How do you put a belt back on a golf cart?
Answer provided byFirst, raise the golf cart engine cover to access the drive belt inside the engine compartment. ... Next, loosen the drive belt tension bolt with an open-end wrench on the front pulley. ... Finally, pull the front pulley to increase the belt tension. ... MORE: Average car insurance cost in 2021.
How do you tighten the drive belt on an EZGO golf cart?
There is no way to adjust a drive belt, so it's important to get the right size belt in the first place. To be sure, visit your local mechanic or call a certified technician to help you get the right drive belt for your EZGO golf cart.
How Loose Should a golf cart drive belt be?
The reason for a Club Car drive belt being too tight can be because the drive belt is too small for the golf cart. The way to check if the belt is fitted correctly is to push the belt down with one finger at the center between the clutches. It should not deflect more than 1.5inches. It should not be less as well.
How do you put a drive belt on a club car?
The drive belt is plainly visible. Loosen the drive belt tension bolt, with the open end wrench, on the front pulley. Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley.
How does EZGO clutch work?
0:463:28How a golf cart CVT slip drive clutch works - YouTubeYouTubeStart of suggested clipEnd of suggested clipMaking the revolution path smaller like dropping the chain on the back of your bike down to aMoreMaking the revolution path smaller like dropping the chain on the back of your bike down to a smaller gear causing the belt to rotate even faster.
How tight should a starter belt be on a golf cart?
0:152:00How to Check the Belts in your Gas Golf Cart | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipDown below and you don't want to press the moderate pressure on that belt you're gonna want to seeMoreDown below and you don't want to press the moderate pressure on that belt you're gonna want to see about 3/16 to 1/4 inch of deflection. There no more than that that'll be your proper.
How do you fix a clutch on a golf cart?
Cleaning the clutch thoroughly might be the simplest solution to this problem. You could also try lubricating the system with a good quality lubricant. This might free up the clutch and thus prevent the squeaking noise. Another common reason could be due to the weights present inside the system hanging up.
How do you rebuild a clutch on a EZGO golf cart?
0:395:37GBoost E Z GO ClutchKit CKSDEZ19 - YouTubeYouTubeStart of suggested clipEnd of suggested clipFor this cart loosen the leaf spring bolt and slide it back so you'll have room to remove bothMoreFor this cart loosen the leaf spring bolt and slide it back so you'll have room to remove both clutches and belt. Now we can remove both bolts for the driven.
What size is a golf cart belt?
The golf cart drive belt is the larger (1" to 1 3/16" wide), longer and usually looser belt on gas golf cars. It connects the drive clutch (on the engine) to the driven clutch (on the differential) and transfers the power of the engine to the rear wheels. The belt should be loose and free of cracks or delamination.
How do you measure a golf cart belt?
0:002:04How to measure for a go-kart drive belt. - YouTubeYouTubeStart of suggested clipEnd of suggested clipCover. Now the first measurement we're going to take on this is we're going to measure from theMoreCover. Now the first measurement we're going to take on this is we're going to measure from the centerline of the crankshaft. To the centerline of the jack shaft.
How do you put a drive belt on a Yamaha golf cart?
0:152:32HOW TO CHANGE A DRIVE BELT ON YAMAHA GOLF CART ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spinMoreJust put the lever in front halfway from reverse and forward. Once it's in reverse and you can spin the back off.
How tight should golf cart starter belt be?
0:152:00How to Check the Belts in your Gas Golf Cart | Golf Cars UnlimitedYouTubeStart of suggested clipEnd of suggested clipDown below and you don't want to press the moderate pressure on that belt you're gonna want to seeMoreDown below and you don't want to press the moderate pressure on that belt you're gonna want to see about 3/16 to 1/4 inch of deflection. There no more than that that'll be your proper.
How do you tighten the belt on a Yamaha gas golf cart?
0:002:03How to tighten a loose Starter Belt on Yamaha Golf Cart YDRA. G29YouTubeStart of suggested clipEnd of suggested clipAnd wiggle this belt here yeah she's loose. All right my 12 mil uh socket here grab that loosen thatMoreAnd wiggle this belt here yeah she's loose. All right my 12 mil uh socket here grab that loosen that up 17 mil wrench here wrap this down. There you go.
How do you change a belt on a Yamaha golf cart?
0:563:29Yamaha Drive 2 Quietech G29 Drive Belt Replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst and then you can remove it from the front clutch make sure that your cart is in neutral. SoMoreFirst and then you can remove it from the front clutch make sure that your cart is in neutral. So the cart can freewheel back and forth without turning the clutch.
Why is my EZGO Drive Belt Too Tight?
The reason your EZGO drive belt is too tight can be because you’re not using the right size drive belt.
How to stop a EZYGO drive belt from slipping?
How to stop a EZYGO drive belt slipping: Make sure that you have the right drive belt. Sometimes the wrong drive belt will not be as wide as the clutch you are putting it on. This gives it an unwanted room to move back and forth when you are using the golf cart.
How to tell if golf cart drive belt is too tight?
To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger. If it deflects less than 1.5” it’s too tight.
What is the belt on a golf cart?
The drive belt on a golf cart connects the two clutches (the drive clutch and the driven clutch) and distributes the power from the engine to the rear wheels.
Why is my EZGO belt so loose?
The reason your EZGO drive belt is too loose could be because it’s worn out, or you’re simply using the wrong size drive belt. In this case, need to find a replacement immediately.
What does it mean when the drive belt is misaligned?
Check and see if the drive belt appears misaligned? If so, is it misaligned more towards the driven clutch (the one on the axle) or the drive clutch (the one on the motor)? If it’s misaligned there is something wrong with the drive clutch.
What to do if your clutch is not working?
Once you’ve confirmed that the drive clutch is not functioning properly you either need to have it fixed or replace. Call a trusted certified technician to have it fixed or replaced for you.
How to change the belt on a golf cart?
Slide the old drive belt off the front drive clutch pulley, and then the rear clutch pulley. Slip the new belt around the golf cart's clutch pulley, and then stretch it out over the front pulley. Pull the front pulley forward slightly to increase the belt tension, and then tighten the tension bolt with the wrench.
Where is the drive belt on a golf cart?
Raise the golf cart engine cover, to access the drive belt inside the engine compartment. The drive belt is plainly visible.
Why is my club car not engaging?
Over time, such belts can become dry and cracked, or may even break. If the cart is having trouble accelerating or will not engage at all, it may be because the belt needs changing.
Special offers and product promotions
Amazon Business: Make the most of your Amazon Business account with exclusive tools and savings. Login now
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Is the drive belt adjustable?
The drive belt is not adjustable. The motor mounts are adjustable and are set for a new belt. If the belt is excessively loose then the belt needs to be replaced or you have a probelm with either the drive or driven clutch.
Can you tighten a belt with motor mounts?
The motor mounts should not be used to tighten the belt due to wear. The clutch requires a special puller to remove it. It may be cheaper to take it somewhere rather than spend the modey on the puller.
Does a 1997 EZ Go golf cart run?
1997 EZ-Go Gas Golf Cart has run fine. A couple of weeks ago, the cart was parked with lights left on. When we went to use the cart the battery was dead. After charging battery, it now it cranks -- bu… read more