Golf-FAQ.com

how to install timing belt on ez go golf cart

by Jeanne Rolfson Published 2 years ago Updated 2 years ago
image

Locate the primary drive clutch. It’s located at the bottom of the two clutches and is the smaller one. Take note of how the existing belt has been adjusted to the clutches and then remove it. Slide in the new belt to the primary clutch and pull it all the way around the secondary clutch the same way the old belt was adjusted.

If you pull the belt off you'll see it. So you line up the notch. On this gear with that dot in theMoreIf you pull the belt off you'll see it. So you line up the notch. On this gear with that dot in the back of this you line this little circle up with this notch here.

Full Answer

Videos of How To Install Timing belt on Ez Go Golf Cartbing.com/videos

How to Adjust the Drive Belt on an EZGO Golf Cart There is no way to adjust a drive belt, so it’s important to get the right size belt in the first place. To be sure, visit your local mechanic or call a certified technician to help you get the right drive belt for your EZGO golf cart.

Images of How To Install Timing Belt On EZ GO Golf Cartbing.com/images

At the top of the motor you will see a knotch, and on the cam gear you will see a hole, line those up, make sure the crank keyway is straight up, and put it all back together. What should compression be on a ezgo golf cart?

How to adjust the drive belt on an EZGO golf cart?

The drive belt should not be too tight. If it’s too tight it can risk wearing off faster and it’s also harder to shift gears. To check if your drive belt is set just right make sure your golf cart is turned off then check the drive belt by pressing it down between the two clutches with your finger.

How do you line up cam gears on an EZGO golf cart?

A loose drive belt can result in your EZGO Golf Cart to lose top speed and underperform. If the drive belt is the right model but it seems to be too loose then it could be because there is something stuck in the clutch or there is some damage in the clutch. In this case you’ll need to call a certified technician to inspect your golf cart.

Can a drive belt be too tight on a golf cart?

Why is my EZGO golf cart losing top speed?

image

How do you change a belt on a EZGO golf cart?

1:195:57Drive belt to remove it all you got to do is kind of work it over the edge and then roll. Back.MoreDrive belt to remove it all you got to do is kind of work it over the edge and then roll. Back. Until it pops off that rear driven clutch and then take it right out.

Why wont my EZGO golf cart go forward?

The main reason why a EZGO gas golf cart will not go forward is because of a locked up brake, or a faulty solenoid and accelerator. A defective Run/Tow or Forward/Reverse switch can also cause a EZGO to not move forward.

How tight should a golf cart drive belt be?

The reason for a Club Car drive belt being too tight can be because the drive belt is too small for the golf cart. The way to check if the belt is fitted correctly is to push the belt down with one finger at the center between the clutches. It should not deflect more than 1.5inches.

Why won't My EZGO start?

Check to make sure the golf cart transmission selector is in the "park" position. Some models of E-Z-GO gas-powered carts may fail to start with a charge if the selector is not fully in the "park" position.

Why won't my golf cart go forward or backwards?

If the power from the battery pack is not reaching the motor, then the Club Car golf cart won't move forward or reverse. In such cases, there are a few components in between the two that need to be checked. The solenoid is one major component. Check if the resistor between the two big terminals on the solenoid is hot.

Why does my golf cart click but not move?

A Club Car golf cart can start clicking but not move, due to dust accumulating inside the battery ports. Opening the battery ports and checking whether there is any dust accumulation can tell you if this is the case. Cleaning it thoroughly with a cloth can resolve the problem.

How do I know if my golf cart belt is too loose?

0:012:00Down below and you don't want to press the moderate pressure on that belt you're gonna want to seeMoreDown below and you don't want to press the moderate pressure on that belt you're gonna want to see about 3/16 to 1/4 inch of deflection. There no more than that that'll be your proper.

When should a golf cart belt be replaced?

Over time, such belts can become dry and cracked, or may even break. If the cart is having trouble accelerating or will not engage at all, it may be because the belt needs changing. Park the golf cart, and turn off the engine. Raise the golf cart engine cover, to access the drive belt inside the engine compartment.

Can you adjust a golf cart clutch?

If you are unsure about removing the drive belt or the clutch, then you can adjust it. Just take out the belt and wound it again with the secondary clutch according to the requirements, and your problem should be fixed.

Where is the reset button on an ezgo golf cart?

Locate the motor Remove the panel so the electric motor is visible. Electric motors usually include reset buttons that can perform similar to circuit breakers. Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.

What would cause a golf cart not to start?

As the main source of power to your electric golf cart, the batteries are commonly the cause for why your electric golf cart won't start. Acid-based batteries are typically used for electric golf carts and must be recharged in order to work properly.

What does EZGO ignitor do?

EZGO Ignition Switch, Ignitor, Coil Parts Ignition coils transfer voltage from your battery into spark for your engine to fire. We carry ignition coils for EZGO TXT, RXV, Marathon, and ST350 Workhorse golf cart models.

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9