Directions:
- 1: Measure and mark all of the 2x4s and cut them to length.
- 2: Measure and cut the dowels to length.
- 3: Drill and countersink holes on each of the upright supports. 3 – 1″ holes measured 1 1/2″ from the top, 13 1/2″ from...
- 4: Cut out triangular supports. Drill three holes at the base of each triangular support.
- 5: Screw the triangular supports to the edge of...
Full Answer
How do you make a bird out of a golf ball?
Mark your locations for legs and antennae and drill the holes in the golf balls. I drilled mine approximately 3/4″ inch deep. BIRD: The bird’s tail is created with one 10″ piece of wire, shaped in a loop , and inserted into 2 holes at back of golf ball.
What can you do with old golf balls?
DIY golf ball craft garden buggies using old golf balls to make lady bugs, bumble bees, frogs, birds, and more. If you are a golfer or have one in your family, you have a similar situation that we have. A stash of used golf balls! As the temperatures warmed up, so did…
How do you drill a hole in a golf ball?
Secure the golf ball in some way that will make it easy to hold on to. I would not recommend to try and just hold it with your hand. Drill your hole, top-dead-center, about 3/4 of the way through the ball. Use a hammer, drive the screwdriver shaft into the ball. It should be very snug.
How do you make a golf ball antenna?
1 Prepare the golf balls (wash, drill holes) 2 Prepare wire for legs and antennae 3 Drill holes and add wire pieces to golf balls (legs and antennae) 4 Glue metal nuts and washers to golf balls (noses and eyes) 5 Prime and paint everything
How do you make a golf ball display case?
0:1352:09Build a Golf Ball / Challenge Coin Display Case - YouTubeYouTubeStart of suggested clipEnd of suggested clipTogether kind of test and see what i want to do how i want to design it you know figure out where iMoreTogether kind of test and see what i want to do how i want to design it you know figure out where i was going to put these like a little divot deals whatever for the golf balls.
How do you put a golf ball on a block of wood?
4:1210:26Fun Scrap Wood Projects - Magic Golf Ball and Cube Within a CubeYouTubeStart of suggested clipEnd of suggested clipThe trick is to heat up some water to almost boiling and submerge the wood in the water for aboutMoreThe trick is to heat up some water to almost boiling and submerge the wood in the water for about seven or eight minutes. This makes the wood more pliable.
Is there an illegal golf ball?
The longest illegal golf ball is the Polara Ultimate Straight. These golf balls are 75% self-correcting and that's going to help reduce hooks and slices. They won't generate as much distance as a normal golf ball but they'll hit a lot more fairways.
Are Golden Bear golf balls good?
The Golden Bear Triple Ti golf balls are perfect for entry level golfers looking for a great value distance ball. Titanium blended high-energy core to give you explosive distance. Aerodynamic dimple pattern maximises performance.
How do you make a cage ball?
0:007:42Ball in a Cage [Broken and glued back together] - YouTubeYouTubeStart of suggested clipEnd of suggested clipThen i'm using a chisel and the best method i can think of to cut a ball out of this solid block ofMoreThen i'm using a chisel and the best method i can think of to cut a ball out of this solid block of wood i'll start off by showing side six because at this point i developed somewhat of a technique.
How do you drill a hole in a golf ball?
0:0814:30What Happens When You Drill Holes in a Golf Ball?! | Inspired by GM GolfYouTubeStart of suggested clipEnd of suggested clipSomething i'm about to drill some holes let's do. This all right so uh kind of a cold morning so iMoreSomething i'm about to drill some holes let's do. This all right so uh kind of a cold morning so i got my garage closed the lighting should be just fine um but let's go ahead and pick a drill.
Why are bandit balls illegal?
The longest illegal golf balls on the market are the 2 piece Bandit golf balls. The USGA had to make these illegal because they have a very aerodynamic dimple design that helps the ball travel a long way. They have low spin off the tee and will dramatically increase the length of your drives.
Does putting chapstick on your driver work?
Chapsticking The Driver Using something like chapstick on your clubface will actually reduce a lot of the spin. When you have less spin you'll have fewer hooks and slices.
Why are nitro golf balls illegal?
First, these golf balls are regarded as illegal in professional rounds due to their special solid cores, which are engineered from mystical powders, allowing them to travel an illegal distance.
What is the number one golf ball on tour?
Titleist likes to remind us that that the Pro V1 is the No 1 ball used by professionals on worldwide golf tours, but that it's a great ball for non-superstars as well. The ball is manufactured to perfectly balance short game control without sacrificing good yardage from the tee.
Who makes Jack Nicklaus balls?
BridgestoneIn the past, Nicklaus has lent his name to signature brands of golf balls, but the new Nicklaus line is proprietary, manufactured to his specifications after three years of testing. Nicklaus said Bridgestone is manufacturing the balls and counseled on its design.
Step 1: How It Works
1) Air is sent through the inlet valve, this pushes the piston (green) forward and sealing the barrel, the air leaks around the chamber and fills the chamber up. 2) Once the air is equalized all around the chamber and valve, the inlet valve is closed. 3) When you want to fire, you open the pilot valve and all the air behind the piston (pilot area) vents out this valve, since the pressure on the piston is un-equalized with more pressure at the front pushing it back, then pushing it forward the piston actuates. 4) The piston flies back at incredible speed and all the air goes out the barrel and launches the projectile. That's how simple it is..
Step 4: Piston Housing Construction
Now you have two options: 1)Servicable piston housing (incase it breaks you can open it up) 2) Non serviceable piston housing (if it breaks your screwed) I recommend the first option, now to achieve this you are going to need to cut a length of 2" Sch40 PVC pipe so it goes all the way inside the tee and hits the 'lip' inside the tee, now cut the pipe so it has about 7cm of pipe coming out of the tee, so the pipe would be around 15cm in total length. With the 7cm of pipe coming out the back of the tee (which is your pilot btw) fit your end cap on it, if when fitted on there is still pipe visable between the end cap and tee, cut the piece of 2" pipe (the 15cm long one) so there is no pipe when the end cap is on fully. Now with your end cap on, grab four screws that are long enough to go through the end cap and piece of pipe but still long enough the stop the piston when it moves back.
Step 5: Pilot Setup
Okay now you need your pilot valve and inlet valve. The inlet valve you hook up to your air compressor, to fill the chamber up. The pilot valve vents the 'pilot area' and actuates the piston which fires the gun.
Step 6: Barrel Setup
When cementing and priming the barrel into the tee (which I will explain later) the barrel needs to extend through the bushing and into the tee like the picture below. That pretty much explains it, you just need to modify the bushing so the barrel can extend through it.
Step 7: Putting It Together
Okay.... Drill a hole in your chamber for a pressure guage and thread it in and then.... Grab your chamber of 3" pipe, a 50" chamber will do. Prime the pipe at one end, prime your 3" end cap, then glue the end of the chamber where the primer ios and do the same for the end cap.
Step 8: The End....My Only Friend
That just about does it. Make sure you prime the pipe first then glue it using PVC solvent, just read the label on the back and you should be fine.
How to make a bumblebee with a golf ball?
Step 1. Decide which buggies you want to make and gather the materials. Step 2. Wash and dry the golf balls. Step 3.
How to get good curls on a buggie?
To get good curls, start with the tips of the wires in the pliers, and curve the wire around the pliers. SAFETY TIP: If these buggies will be used by kids, curl all exposed wire ends so they are not sharp. Step 5. Mark your locations for legs and antennae and drill the holes in the golf balls.
What to draw with a black Sharpie?
After drying, you will use a black Sharpie to draw the eyes, nose, and mouth. Bumblebee = yellow body with black legs and antennae. After drying, you will use a black Sharpie to fill in the black body stripes. Bird = blue body and tail, yellow legs.
Step 2: Connections
cut 2 pieces off of the 2" pipe about 2" long pipe to use to connect the water vavle and the Y to the reducers
Step 3: Fillin' Station
Attach the quick connect to the gas valve. use teflon tape or pipe dope to get a good seal. thread that into one of the reducers and that into the strait end of the Y. thread the preasure gauge into the other reducer and put that into the other branch ot the Y. using one of your 2" pieces attach the Y to one of the 2" to 4" reducers.
Step 4: The Business End
Glue the 2" pipe in one end of the water valve and glue the remaining 2" piece on the other end. on that piece glue the 2" to 4" reducer and then the 4" pipe
Step 5: IT LIVES!!!!!
Glue the two pieces together and then put extra glue on the out side of all your connections just to be sure. be sure to let it dry for a few hours. we shot ours while it was still wet and my friend almost broke his thumb when the end came off.
Step 6: Ready, Fire, Aim
there's really no way to aim so you just gotta point and shoot. MAKE SURE to not shoot it at anyone or any thing that is alive. it will drive a golf ball through a 1/2" of sheet rock. a wash rag is needed to keep a seal around the golfball.
How long does it take to make a golf ball bee?
Time needed: 2 hours. Step by step instructions to make painted golf ball bees. You need one golf ball for each honey bee figure that you want to create. This is a great way to recycle old golf balls that you find on the range or in a thrift store.
How to shape legs for golf ball?
Shape legs in a soft bend and curl the feet sections to avoid sharp edges. Mark and Drill Holes. Use a marker to mark locations for legs and antenna on each golf ball. Legs should go in a line alone each side near the bottom of the ball. A pair of holes for the 2 antennae go near the top of the face.
How to make a bee stinger out of wire?
Check to make sure the wire fits into the drilled holes. Now add a small dot of glue to the end of the wire and insert each on into the proper hole. Optional : Glue a small screw onto the back of the ball to simulate a bee stinger.
Step 1: Project 1: You'll Need a Driver for This Hole..
Turn a "cheap" screwdriver from a dollar store into a better and useful, palm sized screwdriver.
Step 2: Project 1: Take Apart the Screwdriver
The first thing to do here was to cut off the rubber part of the handle.
Step 6: Project 2: a Little Backspin Will Make It Stick..
And a magnet will make a golf ball stick to the fridge! Quick and easy for less than a buck.
Step 7: Project 2: Maulers Ready..
The magnets I purchased where the largest diameter to be found at the dollar store. 6 to a pack, mounted into a plastic "shell".
Step 10: Project 2: Stick It to It..
Place a large dab of hot glue onto the center of a magnet and press it firmly onto the back of the golf ball.
Step 12: Project 3: a Little Pull..
A drawer or door pull! All you need here is one, or several, golf ball (s) and an appropriately sized machine screw (s). Materials: Golf Ball (s) Machine Screw (s) (a #8 size screw of appropriate length should work well) Size the screw length to include the thickness of the drawer or door plus enough extra to go about 3/4 of the way into the golf ball. Tools: Drill and Drill Bits Clamp Surform or Rasp File Screwdriver...
Step 15: Project 3: Screw It to It..
All that's left now is to screw the ball to the front of the drawer or door, or whatever.
