8-Ball in Solid Wood Cube
- Step 1: Parts.
- Step 2: Joint and Plane 4x4. Using a joiner and planer, take the overall size of the 4x4 down to 3" x 3" and cut into a...
- Step 3: Mark the Center of the Cube. Using a straight edge, mark the center of the cube so you know where to drill the...
- Step 4: Router Edges. Using a 1/4" roundover bit, router the cube starting with the end...
How do you get a golf ball into the wood?
To get the Golf Ball into the wood you need to heat up a pan of water and put your block into it. Let it soak for a few minutes and the wood will expand enough to squeeze a Golf Ball into it.
How do you make a teaser out of a golf ball?
All you need to create this teaser is a chunk of softwood (e.g. Basswood) that is 1-3/4″ x 1-3/4″ x 5″, a 1 1/4″ Forstner bit, a drill, and a golf ball. And a pot of hot, near-boiling water.
How to make a super easy golf ball hack?
3 Super Easy Golf Ball Hacks. 1 Step 1: Project 1: You'll Need a Driver for This Hole... Turn a "cheap" screwdriver from a dollar store into a better and useful, palm sized ... 2 Step 2: Project 1: Take Apart the Screwdriver. 3 Step 3: Project 1: Measure and Drill. 4 Step 4: Project 1: Drive It Home. 5 Step 5: Project 1: That's It... More items
How do you glue a magnet to a golf ball?
Place a large dab of hot glue onto the center of a magnet and press it firmly onto the back of the golf ball. Repeat for the next. Step 11: Project 2: the End Game...
How do you put a golf ball in a piece of wood?
To get the Golf Ball into the wood you need to heat up a pan of water and put your block into it. Let it soak for a few minutes and the wood will expand enough to squeeze a Golf Ball into it.
How do you make a wooden Impossible Cube?
0:027:39Impossible pinball in a wooden cube DANGER EXTREMELY UNSAFEYouTubeStart of suggested clipEnd of suggested clipAs you can see there's no way that a pinball is going to fit into that hole. So let me show you howMoreAs you can see there's no way that a pinball is going to fit into that hole. So let me show you how you can do. This this wooden cube right here is about two and a half inches all the way around.
How do you make a golf ball display case?
0:1352:09Build a Golf Ball / Challenge Coin Display Case - YouTubeYouTubeStart of suggested clipEnd of suggested clipTogether kind of test and see what i want to do how i want to design it you know figure out where iMoreTogether kind of test and see what i want to do how i want to design it you know figure out where i was going to put these like a little divot deals whatever for the golf balls.
How do you make a DIY golf ball?
1:342:40How to print Golf ball by hand - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay you activate it must draw activating cloth but press hard with the activating cloth make sureMoreOkay you activate it must draw activating cloth but press hard with the activating cloth make sure it's in the dimples.
How do you make a golf ball cage?
0:0210:26Fun Scrap Wood Projects - Magic Golf Ball and Cube Within a CubeYouTubeStart of suggested clipEnd of suggested clipThe piece already had two Square and flat sides. So squared up the two remaining sides on my planerMoreThe piece already had two Square and flat sides. So squared up the two remaining sides on my planer to the final dimension of one in three quarters of an inch by one and three quarters of an inch.
How do you make a puzzle cubes?
2:3219:0251885 views - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo from here we're gonna go ahead and create a grid of these cubes. Using this rectangular patternMoreSo from here we're gonna go ahead and create a grid of these cubes. Using this rectangular pattern tool. So I'll switch this to selecting bodies I'll click our cube.
How do you make a golf club display rack?
2:063:06$20 DIY Golf Club Storage Rack Project - YouTubeYouTubeStart of suggested clipEnd of suggested clipI probably paid about 20 bucks for a couple of two by fours. Ripped them in half cut them to 32MoreI probably paid about 20 bucks for a couple of two by fours. Ripped them in half cut them to 32 inches in length. And then made this frame with some screws. So it can all be disassembled.
What's the diameter of a golf ball?
1.680 inchesAccording to the USGA Rules of Golf, the diameter of the ball shall not be less than 1.680 inches (42.67 mm). A smaller golf ball will generally fly further than a larger one given the weight is equal. The reason for this is: having a smaller diameter ball means less air resistance.
What can I make out of old golf balls?
Consider these creative ways to put your old golf balls to use around the home.Massager.Light Dimmer Switch. ... Vase Filler. ... Drainage for Potted Plants. ... Critters for the Garden. ... Christmas Ornaments. ... Meat Tenderizer. ... Table Cloth Weights.More items...•11 Creative Ways to Use Golf Balls Around the House - Wise Breadhttps://www.wisebread.com › 11-creative-ways-to-use-gol...https://www.wisebread.com › 11-creative-ways-to-use-gol...
Can you cork a golf ball?
0:168:18Cork Cap Golf Ball | DIY Practice Golf Ball | Works like a Birdie BallYouTubeStart of suggested clipEnd of suggested clipI just got it from a bottle of champagne as you can see and it's actually Prosecco you can justMoreI just got it from a bottle of champagne as you can see and it's actually Prosecco you can just color into and you can have yourself a free golf practice ball let me show you how it's done.Cork Cap Golf Ball | DIY Practice Golf Ball | Works like a Birdie Ballhttps://www.youtube.com › watchhttps://www.youtube.com › watch
What can you make with used golf balls?
What to Do With Old Golf BallsSelling Old Golf Balls. Many people don't know that used golf balls can also be sold. ... Give Away Old Balls. ... Clean & Reuse Golf Balls. ... Turn Old Golf Balls Into Decorations. ... Use an Old Golf Ball as a Massage Tool. ... Use an Old Golf Ball as a Meat Tenderizer.What to Do With Old Golf Balls: 6 Creative Ways to Recyclehttps://www.kansasgolf.org › what-to-do-with-old-golf-ballshttps://www.kansasgolf.org › what-to-do-with-old-golf-balls
Step 1: Select and Cut Wood for Impossible Golfball Project
I figured that this piece of Sapele, leftover from a cutting board project, would work great for the golf ball cage. The piece already had two square and flat sides so I squared up the two remaining sides on my planer to a final dimension of 1 3/4” by 1 3/4.” Next, I took it over to the miter saw and cut a piece 5” long.
Step 2: Mark Guidelines for the Drill Press
Using a ruler I marked a line 3/8” from both ends and then marked a line down the center lengthwise. I flipped the block over and did the same thing on an opposite face.
Step 3: Drill Out the Center Area
Over at the drill press, I set my fence so that my forstner bit lined up with the center line marked on the piece of wood. I used a 1 1/4” Forster bit to drill these holes.
Step 4: Sand the Wood Smooth
I got out the spindle sander and cleaned up the inside edges from the drill press. If you don’t have a spindle sander this can be done by hand sanding. Thats what I keep my shop helper around for.
Step 5: Submerge in Hot Water and Insert Golfball
As you can see, a golf ball can not fit in between the this tight space which is what makes this project so fun. The trick is to heat some water to almost boiling and submerge the wood in the water for about seven or eight minutes. This makes the wood more pliable and allows the spindles to flex enough for the golf ball to fit through.
Step 6: Select and Cut Wood for Cube Within a Cube Project
Next up, I grabbed a 4x4 post that I had in the corner of my shop for about 2 years. Im not sure what I thought I could use it for but I held on to it none the less. I squared it up on the planer and left each side 3 1/4” wide. I used my miter saw to cut off a section at 3 1/4” so that I had a cube that was equal on all sides.
Step 7: Mark Lines to Find Center of One Face
Using a ruler I found the center of one side by drawing a line from one corner to the opposite corner and forming an X. Try to be as precise as possible with these lines so that the center mark is accurate. A little trick I learned from Steve Ramseys video on this project is to mark an X in the same corner of each face.
Select and Cut Wood for Impossible Golfball Project
I figured that this piece of Sapele, leftover from a cutting board project, would work great for the golf ball cage. The piece already had two square and flat sides so I squared up the two remaining sides on my planer to a final dimension of 1 3/4” by 1 3/4.”
Mark Guidelines for the Drill Press
Using a ruler I marked a line 3/8” from both ends and then marked a line down the center lengthwise. I flipped the block over and did the same thing on an opposite face.
Drill Out the Center Area
Over at the drill press, I set my fence so that my forstner bit lined up with the center line marked on the piece of wood. I used a 1 1/4” Forster bit to drill these holes. I also set two stop blocks so that the edge of my forstner bit stopped at the two end lines which will help me be consistent and accurate on both faces.
Sand the Wood Smooth
got out the spindle sander and cleaned up the inside edges from the drill press. If you don’t have a spindle sander this can be done by hand sanding.
Submerge in Hot Water and Insert Golfball
As you can see, a golf ball can not fit in between the this tight space which is what makes this project so fun.
Select and Cut Wood for Cube Within a Cube Project
Next up, I grabbed a 4x4 post that I had in the corner of my shop for about 2 years. Im not sure what I thought I could use it for but I held on to it none the less. I squared it up on the planer and left each side 3 1/4” wide.
Mark Lines to Find Center of One Face
Using a ruler I found the center of one side by drawing a line from one corner to the opposite corner and forming an X. Try to be as precise as possible with these lines so that the center mark is accurate.
