Windmill Mini Golf
- Step 1: Making the 3D Model in Solidworks. This was the most challenging part of the construction in my opinion. ...
- Step 2: Arduino Code. { Serial.println (results.value,HEX); // shows the input value coming from the IR remote.
- Step 3: Putting the Windmill Tower Together. ...
- Step 4: Putting the Box and Circuitry Together. ...
Full Answer
How do you make a mini golf course with a windmill?
No miniature golf course is complete without the legendary windmill hole. Sketch out a design of your windmill. Most feature a small base section decorated at the top with four windmill paddles. Build the base by nailing the two-by-fours together, making a square.
How do DIY windmills work?
DIY windmills are very simple to construct and if you can turn a wrench and operate a drill, then you have enough skills to build a homemade windmill. A windmill generator harness the power of the wind to create electrical power and depending on the size of the windmill can supply part or all of the energy you need.
What is a mini windmill made of?
This YouTube video contains step by step instructions for building a mini windmill that is functional and can provide a few watts of power for lighting. This miniature wind turbine is made of drinking straws and fabric.
How do you make a mini Dutch-style windmill?
This article has been viewed 115,906 times. To make a miniature Dutch-style windmill, start by creating your template. Next, transfer the template shapes to plywood that's ½ to 1 inch thick and cut the shapes out. Paint or stain the wood however you'd like, then construct the windmill body using painter's tape to hold the pieces together.
Step 1: Step 1: Making the 3D Model in Solidworks
This was the most challenging part of the construction in my opinion. Every piece needed to be sized correctly and designed so that it could be assembled. Because of the size of the windmill I have created, the windmill tower had to be printed in three separate pieces and bonded together with plastic epoxy.
Step 2: Step 2: Arduino Code
I included the StepperAK.h, wire.h, LiquidCrystal_I2C.h, IRremote.h, IRremoteInt.h libraries in my sketch:
Step 3: Step 3: Putting the Windmill Tower Together
I inserted a ball bearing in the shaft hole so that the blade shaft could rotate freely. I mounted the DC stepper motor to the platform on the back of the windmill with screws and nuts. I made a small hole on the end of the shaft so the motor could fit into the shaft. Every piece of the tower was bonded together by epoxy.
Step 4: Step 4: Putting the Box and Circuitry Together
All of the electric components are inside the black box behind the windmill other than the DC stepper motor. The LCD display is screwed to the large opening on the side of the box. A small hole was made for the IR sensor to be exposed, but I had to drill the hole larger so I recommend modifying the box in SolidWorks so that issue can be avoided.
How long does it take for a Dutch windmill to dry?
Once you have painted or stained your pieces, let them dry completely. This may take 24-48 hours, depending on the humidity in your area. If you use paint, choose an outdoor latex paint.
How to make a baseball tail?
The tail will be shaped like an elongated baseball “home plate.”. Draw a 6” square on a piece of ½” plywood. Place a ruler or straightedge at the top of the square 2” from the outer edge of the square. Tilt it to a 45-degree angle.
Why are windmills used?
Windmills have been used for centuries to harness the power of the wind. They are also charming decorative additions to a backyard or garden. While these windmills can't turn wind energy into electricity, they can add some whimsy to your landscape.
How many people edit wikihow?
To create this article, 14 people, some anonymous, worked to edit and improve it over time. This article has been viewed 104,698 times.
How to make a body shape with painter's tape?
Use painter’s tape to connect the body pieces. Place strips of painter’s tape near the top, middle, and bottom of every joint created in the previous step. This will keep your side pieces together while you form the body shape. ...
How to make a sandbox out of wood?
Place another side piece next to this one, also with the short end at the top and the long end at the bottom. Place a pencil between these pieces and push the wood together to form a gap the width of the pencil. Repeat this process with the remaining side pieces until you have laid all six side by side. ...
How to make a windmill?
If you use paper, use a heavyweight paper such as butcher paper or posterboard. The shape should be 9 inches on top, 12 inches on bottom, and 20 inches tall . Cut out the template. This will be used to create the sides of your windmill.
1- Small DIY Windmill
This YouTube video will provide you detailed instructions for constructing a small wind-powered generator. The generator is small, easy to build and ideal for providing electrical energy for outdoor lighting or other small-scale power needs.
2- DIY Mini Windmill
This is a great project for a school class that is learning about alternative energy sources. This YouTube video contains step by step instructions for building a mini windmill that is functional and can provide a few watts of power for lighting.
3- Straw and Fabric DIY Windmill
This miniature wind turbine is made of drinking straws and fabric. The straws are used to create the frame of the windmill blades and then covered with lightweight fabric that can easily turn in the breeze.
4- Deck Sized Windmill
This stylish wooden windmill is small enough to fit on your back deck. It adds decor and keeps the air circulating while you enjoy sitting outdoors.
5- Cardboard Windmill Project
Students can learn how to build a small wind turbine cardboard and glue. The result of this cardboard windmill project will provide enough power to run a small LED light bulb.
6- Homemade Wind Generator
Watch this detailed video to discover how that bicycle repair shop owners created a homemade wind generator to provide electricity to their off-grid shop.
7- Working Cardboard DIY Windmill
Here is another cheap idea for building a windmill as a school science project, and it’s made from cardboard.