How To:
- Make the club by cutting out a piece from the cardboard scrap as shown in the collage below for the bottom of the club, cover with duct tape and trim.
- Stick the 2 paper towel rolls together with the duct tape using the half piece cut lengthways as a brace over the join. ...
- Tape the cardboard “club” to the end.
- Golf club made!
How do I build my own golf club?
Simply follow these instructions to get your golf club built. You will find a link to each tool used. Use a Golf Shaft Cutter to cut the shaft per the recommended tip trimming instructions. Using the Grit Edge Blade mounted in a hacksaw frame, cut the shaft per the recommended tip trimming instructions.
Where can I buy custom golf clubs?
You can buy all the components from one place like GolfWorks or Golfsmith, or shop around on eBay. In the end you'll have a set of custom clubs that you'll be happy to talk about and use as the reason for your great (or poor) performance on the course. Now take all the money you saved and take some lessons!
How do you keep score in a golf tournament?
Keep score. You may print out a fun scorecard online or simply keep the score using a pen and paper. Mark down the number of attempts each player takes to finish each hole. The player with the lowest score wins.
How do you make a paper golf course?
DirectionsGather recycled boxes.Cut out large holes in the front and back of the box. ... Paint or use markers to decorate the boxes. ... Use the construction paper, markers, tape, and bamboo skewers to create golf flags. ... Then head outside to set up your golf course.
How do you make golf clubs at home?
3:1524:05BUILDING MY NEW IRONS FROM SCRATCH... AT HOME!? - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm gonna talk you through the process. So the process I'm going to do with these I'm going to sandMoreI'm gonna talk you through the process. So the process I'm going to do with these I'm going to sand initially the paint off the shaft I've gone with black shafts.
How do you make a cardboard Golf Club?
1:258:53How to make a golf game (indoor edition) - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn any one of the cardboard pieces you want to use a pen or a marker and trace the bamboo stick onMoreOn any one of the cardboard pieces you want to use a pen or a marker and trace the bamboo stick on that piece of cardboard at an options.
How do you make miniature golf clubs?
0:1442:15Miniature Golf Caddy & Clubs Tutorial - jennings644 - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt is wired but you don't need the wire. So I'm just gonna chop mine just chop a piece off. So we'veMoreIt is wired but you don't need the wire. So I'm just gonna chop mine just chop a piece off. So we've got that we're going to need some of these skewers submit the golf clubs.
How do you make a club?
Step 1: Know Why Your Club Exists. ... Step 2: Structure Your Club & Governance. ... Step 3: How to Get New Members. ... Step 4: Outline the Financial Structure. ... Step 5: Create a Club Website. ... Step 6: Hold Your First Club Meeting. ... Step 7: Attract & Engage Your Members.
How do you make your own irons?
1:347:21How to Build a Set of Irons - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure everything's square. I've got my three iron lengths. I'm going to mark that and next IMoreMake sure everything's square. I've got my three iron lengths. I'm going to mark that and next I would go over the cutting wheel I'm going to cut this shaft to the proper three arm. Length.
How do you make a golf putter?
0:408:46I built a CUSTOM Hand-carved Golf Putter - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe next mission is to create two chambers that would be carrying the weights of the putter. So IMoreThe next mission is to create two chambers that would be carrying the weights of the putter. So I created a line down the bottom. And then made two incision. Points where I'll take my Forstner.
How do you make a mini golf hole?
0:044:28How to Build a Miniature Golf Course | This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipIn it's a really cool system it's a series of panels you can set up any way you want to build yourMoreIn it's a really cool system it's a series of panels you can set up any way you want to build your own golf course inside the house we're covering it with green felt to make it look like grass.
How do you make mini golf fun?
Creative Ways to Enjoy Mini GolfHole 2: Introduce some competition by dividing your group into teams of two. ... Hole 6: Raise the challenge bar. ... Hole 7: Turn around, face backward and putt the ball through your legs.Hole 8: Try sideways soccer. ... Hole 9: Hold the club like a pool cue and guide it in.More items...•
How do you make a mini putting green in golf?
2:584:16Make It: 5 Golf Putting Green Super Upgrades for $10 or Less - YouTubeYouTubeStart of suggested clipEnd of suggested clipI'm gonna make a blue one and a red one this is a 7 inch piece of duct tape. And I'm just gonna rollMoreI'm gonna make a blue one and a red one this is a 7 inch piece of duct tape. And I'm just gonna roll it bring it over and here's the tricky part just gonna have to come down flat.
How do you make a golf game?
0:0915:35How To Make Golf Game In Scratch 3.0 - YouTubeYouTubeStart of suggested clipEnd of suggested clipToday's game we're gonna make a golf game in scratch. It's gonna be a fun one infinite levels youMoreToday's game we're gonna make a golf game in scratch. It's gonna be a fun one infinite levels you can have your own you can play as many times as you want of course.
How do you play Putt Putt?
2:164:02How to Play Mini Golf, Part 1 - YouTubeYouTubeStart of suggested clipEnd of suggested clipEveryone should hit their first. Shot. Then the person whose ball is closest to the cup continues toMoreEveryone should hit their first. Shot. Then the person whose ball is closest to the cup continues to hit until their ball goes in or until.
How to make a hole in a game?
Hole 1: Create a ramp with a book leaning against musical chimes or a toy xylophone. If hit properly, the ball moves up the ramp and over the chimes to create a fun sound before it makes it to the hole. Hole 2: Use canned food or cereal boxes as obstacles and use your kitchen to create a fun food theme.
What is mini golf?
Let your kids know what mini golf is. Mini golf is a game where players try to get a ball in a hole in the least number of shots. Mini golf is fun because you can create fun obstacles for your holes. While traditional golf is played with 18 holes, mini golf is played with nine but you can vary how many holes depending on the location.
How to cut a hole in MDF?
Cut your hole. Close to one end of your MDF panel, mark of your hole slightly off-center. Make a hole at this mark with a drill fitted with 4-inch hole saw. Flip the panel over once the drill has poked through and continue cutting the hole from the other side to prevent the MDF from splintering.
How to make a bucket out of duct tape?
Community Answer. Just cut the bottom of the bucket out to make it. The lower three inches. Then you make an opening through each piece, and attach them with duct tape. Line up the (open) ends, and then you can spread them apart to make a loop. Once you've done that, screw (or tape/glue) the sides to a block.
Is mini golf good for kids?
This is a great course for very young children. The driveway mini-golf course is great for accuracy as the difficulty increases as you place the holes further and further away. Tape down your cups as each hole and place them at varying distances from the edge of the driveway.
Step 1
Make a 2 ¼-inch cut across the bill at points 1 inch from the top and ¾ inch from the bottom. At the end of the bottom cut (when you are about ¼ inch from the opposite edge of the bill), pivot your scissors and snip down 3/8 inch toward the bottom of the bill. See Fig. 1.
Step 2
Fold over the center portion of the bill 1/8 inch to begin making the shaft. Continue folding over and over until you reach the opposite edge, creasing each fold sharply to make it lie flat. See Fig. 2.
Step 3
Make the grip by loosely folding the top 1-inch section around the shaft. Crease each fold. See Fig. 3.
Step 4
Make the head by folding over the side edge opposite the shaft 1 inch on the remaining ¾-inch bottom section. Fold the top and bottom corners of the folded edge toward each other in the center to create a point. See Fig. 4. Fold the head in half horizontally.
Step 5
Fold the bill at a slight angle to make the head tilt at the point where the shaft and head meet.
Step 1: Material List
For this instructable you will need a few things like: - A pencil - A utility knife - A staple gun - Some weights - Clamps - A long ruler - Clothes pins - A bottle of wood glue (I used gorilla glue) - Duct tape (I used gorilla tape) - Sand paper - A place to work - And a whole lotta cardboard
Step 2: Making the Base
For the base I used one big 54"u001d x 30"u001d inch piece of cardboard and an other 54"u001d x 26"u001d inch piece of cardboard. Re-enforced by gluing other pieces of cardboard on the bottom. In order to fuse them together I placed 2 bar stools and boxes as weights, to make sure the edges fused together, I used clothes pins.
Step 3: Attaching the Side Railing
Now you will need four pieces of small cardboard to make the railing so the ball doesnu0019t fly out of the course when your trying to putt. I used some packing boxes that I got from a UPS store the model number is s-4625 (in case you want to get the same ones). That particular box can be folded really easily into a triangle.
Step 4: Making the Hinges
One piece of cardboard needs to be slightly bigger so that it folds and stores properly. I hinged them together with a creased piece of cardboard, I glued it to the bigger pieces of cardboard, stapled them and put a little bit of gorilla tape on the sides just to make sure it didnu0019t come off because if that comes off the whole thing is ruined.
Step 5: Making the Hole
The first thing I did was cut the tube that would be the hole, I cut it to 5", then in order to make it stand in place I cut a sliver of the bottom, and glued it to the base. The back end of the box is 7" x 29", the top of it is 6" x 22.5", and the front is 6" x 21.5" The back piece had tabs to aid in the gluing also a place to staple the box in place, the front part had tabs on the inside which were used for gluing & stapling.
Step 6: Getting the Texture
You need the texture on the foundation otherwise the ball will roll too fast and it will be impossible to get the ball in the hole. So what you do is get some cardboard and soak it with water and then peel off the first layer of cardboard just enough to get the texture that'u0019s inside all cardboard.
Step 7: Attaching the Texture
Now that you have the texture, its time to glue it to the base. Once you'u0019ve done that put a sheet of cardboard on top of it and then put on your weights. If you put the weights on without the cardboard it will smash the texture and it will defeat the whole purpose of having the texture.
Step 1a (Steel Shaft Tip Trimming)
Use a Golf Shaft Cutter to cut the shaft per the recommended tip trimming instructions.
Step 1b (Graphite Shaft Tip Trimming)
Using the Grit Edge Blade mounted in a hacksaw frame, cut the shaft per the recommended tip trimming instructions. Apply a piece of masking tape to the shaft at the cutting point to prevent splintering the fibers of the graphite shaft.
Step 2 (All Shafts)
Measure the hosel depth of the clubhead to be assembled by inserting the shaft tip into the clubhead and placing a mark on the shaft next to the hosel. With graphite shafts, use a pice of masking tape to mark the depth. It is very important that the shaft penetrates completely to the bottom of the hosel.
Step 3a (Steel Shafts)
Sand the tip of the shaft with 100 grit sand paper to remove the shiny finish. This operation is “prepping” the shaft and can be done by The GolfWorks.
Step 3b (Graphite Shafts)
Lightly sand shaft from tape to tip with 150 grit or finer sand paper to remove the polyurethane finish and all the paint. This operation is “prepping” the shaft and can be done by The GolfWorks.
Step 4
The steel shaft tip should have a uniform satin or brushed appearance. The graphite shaft tip should have a uniform grayish graphite appearance. Prepping ensures better adhesion of the epoxy to the shaft.
Step 5
If using a ferrule, slide it over the shaft tip. Note: A small amount of epoxy can be applied to the shaft tip prior to installing the ferrule. This helps the ferrule slide into place easier and keeps the ferrule secure.
How to make a golf club?
Step 1: What You Need 1 8 shafts (graphite or steel, your choice). 8 will make you a 4-SW set. (no one uses a 3-iron anymore). Make sure your shaft tip size matches the type of heads youu0019ll be using (i.e. .370 shafts for .370 hosel bore on the heads). 2 Club heads. I'u0019ll focus on irons, but most of the steps in this instructable also apply to woods and hybrids. You can spend anywhere from a few dollars a head to a few hundred, so you might want to start off cheap before going to an expensive set. I've found great sets of heads on eBay for a fraction of their retail value.
How to put a golf club in a vise?
Using the rubber shaft holder, set the assembled club into your vise. Cut a piece grip tape a little smaller than the size of the grip and wrap it around the butt end of the shaft . Make sure there is a little bit hanging over the end and tuck it into the shaft.
