How to Measure Golf Club Loft Angle (Step-by-Step)
- Collect Tools. Before you start the processing of measuring the loft of your clubs, you are going to need to collect...
- Set Up a Flat Surface. Potentially the most critical part of this process is to make sure the club is sitting on a...
- Put the Golf Club Shaft in Place. As you will notice on the lie-and-loft...
How to measure the loft of a golf club?
Before you start the processing of measuring the loft of your clubs, you are going to need to collect a few supplies. It is possible to measure your club’s loft using a protractor, but these measurements will not be very accurate. It is hard to get the base of the club to sit in place and hold a standard protractor properly to get the measurement.
Do higher lofted golf clubs hit the ball higher?
All else being equal, you’ll hit the ball higher with a higher-lofted club, although the more loft a club has, the more distance that is sacrificed. Lofts of specific clubs are fairly standardized but can vary among different manufacturers.
What is loft gapping in golf?
Loft gapping in golf is the difference between the lofts of your clubs. For instance, if you have a pitching wedge that is 43 degrees, you will want to know how many degrees of loft your nine iron has. If the nine iron only has 44 degrees of loft, you will not notice much of a difference in the distance that you can hit these clubs.
How do you measure the angle of a golf club?
Then, turn the bottom of the club head so it's at a 60-degree angle to the surface you're measuring the club on. Finally, use a tape measure to measure from the end of the grip to the point where the bottom of the club head meets the flat surface.
How do I know what loft wedge I have?
Know your pitching wedge loft. If it's 45 degrees or less, add three more wedges that are spaced apart by no more than 4-5 degrees each. So generally think about putting in a gap wedge that's 48 or 50 degrees, a sand wedge that's between 54 and 56 degrees, and a lob wedge that's between 58 and 60 degrees.
What is the loft of my clubs?
The loft of a golf club is the angle created between the clubface and the ground - and will be different for every club in your bag. The loft will have a direct impact on the distance the ball travels - the lower the loft, the further the ball will go.
How do you measure Loft?
The crucial measurement you need to take is from the highest point, directly under the roof ridge, vertically down to the top of the joists below. This can be done with a tape measure, ideally, a metal one that will remain straight. For a conversion to be practical, the height needs to be at least 2.2 metres.
Where is the loft on a golf club?
The loft of a club is the angle formed by the intersection of the line of the clubface and the line of the shaft. Each club found in a golfer's bag will have a different loft angle, usually ranging from 8.5° for a driver with a low ball flight up to around 60° for a lob wedge.
How do you determine the loft and lie of an iron?
0:263:40Checking Your Lofts and Lie Angles - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then our lie angle is coming in at about 59 degrees so you're looking at about two and a halfMoreAnd then our lie angle is coming in at about 59 degrees so you're looking at about two and a half degrees flat and one degree strong that could be based on specs these are the read spec for callaway.
What loft should a 7-iron be?
34 to 35 degrees7-Iron Loft | 28 to 35 Degrees A more standard loft for a 7-iron is 34 to 35 degrees, but you can find game improvement 7-iron lofts pushed as low as 28 degrees or less.
What is the standard size of a loft?
DimensionsDimensionsHeightTwinLow Loft50.75"L: 100.75" W: 42.5"Mid Loft/Low Bunk61.5"Medium Bunk66.25"High Loft/High Bunk71"
How is the lie of a golf club determined?
Draw a straight line on the back of the golf ball, and have it facing the clubhead. After you make impact the line will appear on the face. If it's pointing towards the toe, then your club is too upright. If it's pointing towards the heel, then it's too flat.
How do you measure the offset of a golf club?
Offset: The distance from the forward edge of the hosel to the leading edge of the club's face, which is trailing the hosel. On-set: The distance from the forward edge of the hosel to the leading edge of the club's face, which is forward of the hosel.
What golf club is 37 degrees?
An 8-iron has 37-degrees of loft and will carry approx 130-yards. A 9-iron has 41-degrees of loft and will carry 120-yards. A Pitching Wedge has anything between 45 to 50-degrees of loft. Carry will be approx 105 to 110-yards.
Is a 9.5 degree driver hard to hit?
Having a driver with less loft will require more speed to get the most out of it. If your swing speed isn't fast enough then you'll likely get lower shots that won't go as far. You also need to look at the angle your driver hits the ball....9 vs 10.5 Degrees: Accuracy.9 Degree DriverFairway Hit?Shot Dispersion90 yards10 more rows
What club is 23 degrees in golf?
A 5 iron typically has around 23 or 24 degrees of loft. This is very similar to the 5 hybrid golf clubs. A 5 iron is often a borderline club in the bag where golfers will switch between irons and hybrids and potentially decide to take the 5 iron out of the bag.
What is the loft of a golf club?
Each golf club in your bag should have a different loft. A golf club’s loft – the angle of the clubface relative to the shaft – helps determine how high you’ll hit the ball. All else being equal, you’ll hit the ball higher with a higher-lofted club, although the more loft a club has, the more distance that is sacrificed.
Can you check the loft of a golf club?
Additionally, standard lofts have changed a bit over time. If you want to check the loft of your clubs, or perhaps you wish to buy a used club and the owner doesn’t know its loft, you can check it yourself with the proper tool.
Gather Your Tools
While it is possible to measure the golf club loft using a protractor, we strongly advise against doing so. It can be cheap, but the problem is that it can be inaccurate. The best tool to have is a golf club lie and loft device.
Put the Golf Club on a Flat Surface
For the most accurate measurements, it is important that you position the golf club on a flat surface. Otherwise, the figures are skewed and unreliable. For a square set-up, it is best if you will measure the golf club on the top of a table.
Insert the Shaft on the Gauge
With the golf club now on a stable position, insert the shaft on the lie and loft gauge. It should sit securely on the device. The clubface must also be square. Chances are, the device comes with a manual that contains pictures of how you must position the golf club. Follow what the instruction says.
Take the Measurement
At this point, you are now ready to note the measurements on the device. You will also see the lie angle. Between the two, the loft is usually a higher number.
How to measure golf club?
To measure a golf club, start by laying it on a flat, horizontal surface, like a table or countertop . Then, turn the bottom of the club head so it's at a 60-degree angle to the surface you're measuring the club on. Finally, use a tape measure to measure from the end of the grip to the point where the bottom of the club head meets the flat surface. ...
Which plane should golf clubs be measured on?
Clubs should be measured on a horizontal, rather than vertical, plane to get the most accurate results. ...
How to measure club length?
Calibrate the club length measuring apparatus. Turn on the machine and move the grip support assembly to the left until it reaches the end of the apparatus. Put the calibration rod into the machine, resting the right end of the rod against the 60-degree sole plate of the clubhead support.
How to rock a golf club back and forth?
Ensure the clubhead rests against the clubhead support, with the sole touching the 60-degree sole plate. The grip should rest in the grip support. Gently rock the club back and forth to be sure it’s not being constrained and can move naturally.
Where is the sole on a golf club?
The sole is the bottom of the club head. You may need to rest the sole against a plate to ensure it sits at the proper angle. Measure from the end of the grip to the end of the sole. Use a tape measure to find the length in inches between the end of the grip and the farthest point that the sole contacts the horizontal surface.
mwilkins25
I’m looking for an inexpensive tool to measure loft and lie on my irons.
mwilkins25
The protractor is what you use to measure the loft after the club has been mounted in the loft/lie gauge. e.g. one of these.
Socrates
Found this on the golfmechanix site. Tried to link it here but it wouldn’t work.
mwilkins25
This will work, but you have to know how to make measurements and how to set the club up properly in the device to be accurate.
Socrates
What makes this one more difficult to use vs the more expensive one? I’m less worried about getting the exact loft, what I need is to be consistent across all of my clubs.
mwilkins25
You bought a launch monitor but don’t want a loft lie gauge yet want to know your lofts. You should have started with the gauge and worried about the launch monitor later.
Petem
Find a club that you definitely know the loft of. Place the face onto a flat surface like a table top or worktop with the hosel right up to the edge. If you have a work bench you could clamp the head face down. Measure the shaft just below the ferrule with a phone or digital inclnometer. What ever the difference is apply that to every other club.
osu91gobucks
I do my own club work. I have a Mitchell puller and an economy loft/lie machine from Golfworks. They suit my needs well but I need an accurate way to measure loft. I've tried using the loft/lie machine as a brace, as it comes with an attachment arm, but it's not stable enough and there's too much play in the bracket to get the accuracy I need.
yygolfnb
I started bending and measurement on the cheap as well.
Tellsch
Put the shaft parallel to the ground in a vise. Put a level on the shaft so you know it is perfectly horizontal. Put a micro level on the club face inline with the groves. Make this level as well. Put the angle cube on the face, it will read the proper loft.
Nessism
I made my own spec gauge using a chunk of steel plate, a modified minivan sliding door hinge, and a clamp device taken from a vise. Basically, just a bunch of junk that was laying around the garage. Key thing was to make sure the hinge was on-plane and not tilted fore-aft, so the angle of the shaft is always at 90* to the plate.
mxtitleistgolfer
Take them to your nearest golf shop and ask them to measure the loft and lies. I've never heard of a place that charges just to measure them, only if you end up having them bend them. Plus then you'll know they were put on a propped loft and lie machine.
Nessism
Take them to your nearest golf shop and ask them to measure the loft and lies. I've never heard of a place that charges just to measure them, only if you end up having them bend them. Plus then you'll know they were put on a propped loft and lie machine.
mxtitleistgolfer
Take them to your nearest golf shop and ask them to measure the loft and lies. I've never heard of a place that charges just to measure them, only if you end up having them bend them. Plus then you'll know they were put on a propped loft and lie machine.
