how to measure golf club loft angle at home

• Gather Your Tools. While it is possible to measure the golf club loft using a protractor, we strongly advise against doing so.
• Put the Golf Club on a Flat Surface. For the most accurate measurements, it is important that you position the golf club on a flat surface.
• Insert the Shaft on the Gauge. With the golf club now on a stable position, insert the shaft on the lie and loft gauge. ...
• Take the Measurement. At this point, you are now ready to note the measurements on the device. You will also see the lie angle.

Full Answer

What is the best loft for a golf club?

What Is The Correct Driver Loft For The Average Senior Golfer

1. Loft
2. Swing speed
3. Angle of attack

What are the degree lofts of golf clubs?

What is Loft?

• Standard Iron Lofts. As the game has evolved, technology has developed to make clubs for every type of golfer. ...
• Wedges: ( SW, GAP, LOB) Wedges are “personal” feel clubs. ...
• Hybrids. ...
• Drivers. ...
• Fairway Metals (woods) The range of fairway metals available allows for every skill level to find a club that suits their swing.
• Putters. ...
• Loft. ...
• Final Thoughts. ...

What are the angles of a golf club?

What Are The Degree Loft Of Golf Clubs?

• Driver Degree Loft. A driver loft is traditionally somewhere around the 10 degree mark although there are plenty of exceptions.
• Fairway Wood Loft. Most golfers will carry a 3-wood and the standard 3 wood loft is around 15 degrees. ...
• Hybrid Loft. ...
• Iron Lofts. ...
• Wedge lofts. ...
• Putter Loft. ...

What is the loft of a golf club?

The loft of a golf club is defined as the angle which the shaft makes with the clubhead. In other words, the angle which the clubhead makes relative to the vertical plane with respect to the shaft is defined as the loft.

How do I know what loft my wedge is?

Know your pitching wedge loft. If it's 45 degrees or less, add three more wedges that are spaced apart by no more than 4-5 degrees each. So generally think about putting in a gap wedge that's 48 or 50 degrees, a sand wedge that's between 54 and 56 degrees, and a lob wedge that's between 58 and 60 degrees.

How do you measure golf club angles?

The specification gauge disciples in the golf industry have long advocated the only way to measure club angles is by placing the club head on its sole center (defined by the middle of the score lines) on the base of the specification gauge.

What loft are my clubs?

In the longer irons a three-iron usually comes in at around 20 degrees, a four-iron at roughly 25 degrees and a five-iron at 29 degrees of loft. A six-iron is typically 31 degrees, a seven-iron is usually around 34 degree and then the eight- and nine-irons often come with 37 and 41 degrees of loft respectively.

How do you measure golf clubs at home?

0:522:42Measuring Golf Club Length Video Blog From Hireko Golf Part 1YouTubeStart of suggested clipEnd of suggested clipThe club needs be positioned. With the center of the sole touching the ground in your ruler. Back byMoreThe club needs be positioned. With the center of the sole touching the ground in your ruler. Back by the heel touching the ground. This is the correct way to measure. If the club is too upright.

Is there a protractor app?

Protractor helps you to measure angles quickly and easily. This app turn your iPhone into a handy pocket protractor that can measure angles in both degrees and radians.

How much does 1 degree of loft affect distance?

Given that you're at your maximum clubhead speed, just 1-degree change in the loft angle of a golf driver can affect your driving distance by 2-4 yards. As for irons, the difference in distance between 8-iron (37-39 degrees) and 9-iron (41-43 degrees) is usually 10-15 yards.

How do you determine the loft and lie of an iron?

0:263:40Checking Your Lofts and Lie Angles - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then our lie angle is coming in at about 59 degrees so you're looking at about two and a halfMoreAnd then our lie angle is coming in at about 59 degrees so you're looking at about two and a half degrees flat and one degree strong that could be based on specs these are the read spec for callaway.

What Golf Club is 37 degrees?

An 8-iron has 37-degrees of loft and will carry approx 130-yards. A 9-iron has 41-degrees of loft and will carry 120-yards. A Pitching Wedge has anything between 45 to 50-degrees of loft. Carry will be approx 105 to 110-yards.

Does higher loft reduce slice?

Although many slicers want to hit the ball lower, remember the additional loft provides backspin that will reduce the amount a golf ball slices through the air.

How do I measure my golf clubs with a tape measure?

Measure from the end of the grip to the end of the sole. Use a tape measure to find the length in inches between the end of the grip and the farthest point that the sole contacts the horizontal surface. This is the length of your golf club!

How do you determine golf club height?

Using the ratio of every 6" of height there should be a 1" change in length then there should be a 1 ½" difference between their 5-irons. For example, recommend 36.5" for the lady and 38" for the man (or 36.75" / 38.25").

How do you know if your golf clubs are the right size?

In irons, more so than in the driver, optimal club length is usually determined by a set of measurements that take into account the player's height, arm length, and swing posture. Clearly, a player who is extremely tall would not benefit by using golf clubs designed for a player who is much shorter, and vice versa.

Gather Your Tools

While it is possible to measure the golf club loft using a protractor, we strongly advise against doing so. It can be cheap, but the problem is that it can be inaccurate. The best tool to have is a golf club lie and loft device.

Put the Golf Club on a Flat Surface

For the most accurate measurements, it is important that you position the golf club on a flat surface. Otherwise, the figures are skewed and unreliable. For a square set-up, it is best if you will measure the golf club on the top of a table.

Insert the Shaft on the Gauge

With the golf club now on a stable position, insert the shaft on the lie and loft gauge. It should sit securely on the device. The clubface must also be square. Chances are, the device comes with a manual that contains pictures of how you must position the golf club. Follow what the instruction says.

Take the Measurement

At this point, you are now ready to note the measurements on the device. You will also see the lie angle. Between the two, the loft is usually a higher number.

How to measure golf club?

To measure a golf club, start by laying it on a flat, horizontal surface, like a table or countertop . Then, turn the bottom of the club head so it's at a 60-degree angle to the surface you're measuring the club on. Finally, use a tape measure to measure from the end of the grip to the point where the bottom of the club head meets the flat surface. ...

How to measure club length?

Calibrate the club length measuring apparatus. Turn on the machine and move the grip support assembly to the left until it reaches the end of the apparatus. Put the calibration rod into the machine, resting the right end of the rod against the 60-degree sole plate of the clubhead support.

How to rock a golf club back and forth?

Ensure the clubhead rests against the clubhead support, with the sole touching the 60-degree sole plate. The grip should rest in the grip support. Gently rock the club back and forth to be sure it’s not being constrained and can move naturally.

Where is the sole on a golf club?

The sole is the bottom of the club head. You may need to rest the sole against a plate to ensure it sits at the proper angle. Measure from the end of the grip to the end of the sole. Use a tape measure to find the length in inches between the end of the grip and the farthest point that the sole contacts the horizontal surface.

Which plane should golf clubs be measured on?

Clubs should be measured on a horizontal, rather than vertical, plane to get the most accurate results. ...

How to read scale on a scuba diver?

Slide the grip support until it touches the grip, then read the scale. Move the grip support to the right until the butt plate is gently touching the end of the grip. Step back from the scale and read the digital value. ...

What is the loft of a golf club?

Each golf club in your bag should have a different loft. A golf club’s loft – the angle of the clubface relative to the shaft – helps determine how high you’ll hit the ball. All else being equal, you’ll hit the ball higher with a higher-lofted club, although the more loft a club has, the more distance that is sacrificed.

Can you check the loft of a golf club?

Additionally, standard lofts have changed a bit over time. If you want to check the loft of your clubs, or perhaps you wish to buy a used club and the owner doesn’t know its loft, you can check it yourself with the proper tool.

Invest in a Golf Loft Machine

The most important thing that you will need is a golf loft machine. It is a must-have investment if you want to customize your golf clubs, making sure that the lie angle is at par with your preference. It is essential for measuring and bending golf clubs.

Know the Lie Angle

Before you proceed, you must know the exact lie angle that you want for the golf club. There is no internationally recognized lie angle. The right choice will depend on several factors, such as the specific brand and model of the club that you have.

Use the Bending Bar

After taking the necessary measurement, you can now bend the loft using the bending bar. The latter is what will be doing the magic trick as it bends the loft to the desired angle. You will need enough strength to exert the necessary pressure. Otherwise, the lie angle will not bend as it should.

Measure the Lie Angle

After using the bending bar, you will need to once again measure the lie angle. See to it that it is exactly the angle that you want. Otherwise, you will need to repeat using the bending bar until you reach the right angle.

osu91gobucks

I do my own club work. I have a Mitchell puller and an economy loft/lie machine from Golfworks. They suit my needs well but I need an accurate way to measure loft. I've tried using the loft/lie machine as a brace, as it comes with an attachment arm, but it's not stable enough and there's too much play in the bracket to get the accuracy I need.

yygolfnb

I started bending and measurement on the cheap as well.

Tellsch

Put the shaft parallel to the ground in a vise. Put a level on the shaft so you know it is perfectly horizontal. Put a micro level on the club face inline with the groves. Make this level as well. Put the angle cube on the face, it will read the proper loft.

Nessism

I made my own spec gauge using a chunk of steel plate, a modified minivan sliding door hinge, and a clamp device taken from a vise. Basically, just a bunch of junk that was laying around the garage. Key thing was to make sure the hinge was on-plane and not tilted fore-aft, so the angle of the shaft is always at 90* to the plate.

mxtitleistgolfer

Take them to your nearest golf shop and ask them to measure the loft and lies. I've never heard of a place that charges just to measure them, only if you end up having them bend them. Plus then you'll know they were put on a propped loft and lie machine.

Nessism

Take them to your nearest golf shop and ask them to measure the loft and lies. I've never heard of a place that charges just to measure them, only if you end up having them bend them. Plus then you'll know they were put on a propped loft and lie machine.

mxtitleistgolfer

Take them to your nearest golf shop and ask them to measure the loft and lies. I've never heard of a place that charges just to measure them, only if you end up having them bend them. Plus then you'll know they were put on a propped loft and lie machine.

mwilkins25

I’m looking for an inexpensive tool to measure loft and lie on my irons.

mwilkins25

The protractor is what you use to measure the loft after the club has been mounted in the loft/lie gauge. e.g. one of these.

Socrates

Found this on the golfmechanix site. Tried to link it here but it wouldn’t work.

mwilkins25

This will work, but you have to know how to make measurements and how to set the club up properly in the device to be accurate.

Socrates

What makes this one more difficult to use vs the more expensive one? I’m less worried about getting the exact loft, what I need is to be consistent across all of my clubs.

mwilkins25

You bought a launch monitor but don’t want a loft lie gauge yet want to know your lofts. You should have started with the gauge and worried about the launch monitor later.

Petem

Find a club that you definitely know the loft of. Place the face onto a flat surface like a table top or worktop with the hosel right up to the edge. If you have a work bench you could clamp the head face down. Measure the shaft just below the ferrule with a phone or digital inclnometer. What ever the difference is apply that to every other club.