
How to Measure Golf Iron Length.
- Be sure to use the right measuring equipment. This requires a 48-inch ruler/measurement stick/tape measure.
- The golf club should be positioned in the desired position.
- On a flat area, lay the clubface so that it is parallel to the ground. Afterward, lay your palm on the top of the club in order to keep it firmly in ...
- Placing the measuring stick behind the golf club is a great way to get an accurate reading.
- If you’re measuring a golf club’s shaft, set the stick on the ground directly next to its heel. It’s important that the stick’s numbers are facing you ...
How do you measure a golf club?
What-If Standard Sized Irons Are Not Fit for You Method 1. It is the method that is the most used by the golfers. Here are the steps to measure the length of the golf... Method 2. The following steps are part of the second method of measuring the …
How to size golf clubs for better performance?
How to Measure Golf Iron Length. Be sure to use the right measuring equipment. This requires a 48-inch ruler/measurement stick/tape measure. The golf club should be positioned in the desired position. On a flat area, lay the clubface so that it is parallel …
What is the length of a 5 iron golf club?
Here’s how to go about it to get the correct golf club length for your height… 1. Measure Your Overall Height (i.e. “static” fitting) The measurement of your overall height is the first, most basic step of the process. But please bear in mind that this is not enough for deciding the accurate length of your golf club shaft.
How do I get measured for golf clubs?
A 48” golf club ruler is placed along the backside of the club with the tip of the rule touching the ground by the club’s heel. The final length is measured at the edge of the grip cap (and not the very top). This method is used in all cases except putters that the shaft is not located at the heel.

Why is length important in golf?
Length itself is very important as it helps control the distance you hit the ball as well as develop consistency is the length is fitted correctly.
Where is the final length measured?
The final length is measured at the edge of the grip cap (and not the very top). This method is used in all cases except putters that the shaft is not located at the heel. In this method, it is critical that the lie of the club be positioned correctly. If the club is placed with the toe raised higher off of the ground than the heel, ...
Why is the ruler not placed in line with the shaft?
Because the shaft is ahead of the face of the putter, the ruler is not placed in-line with the shaft, rather along the back side of the shaft like an iron would be measured. The difference being that the ruler would touch the ground somewhere other than behind the heel of the club.
What is the USGA method?
USGA Method. The United States Golf Association (USGA) has a method outlined in the Rules of Golf. The USGA uses an apparatus that has a piece of angle iron as a stop that forms at a 60 angle from the horizontal.
Why measure golf clubs?
You may also need to measure the clubs to ensure that they are regulation length for an upcoming tournament or event. It is important to know the proper way to measure the entire length of a golf club.
Where to place measuring stick on golf club?
Place the measuring stick directly behind the golf club . The stick should make contact with the shaft of the club and be placed on the ground right at the heel of the golf club you are measuring. The numbers on the stick should be pointed toward you so you can easily obtain a reading.
How to hold a golf club steady?
The face of the golf club should be laying flat on a flat surface so that the face is parallel to the ground. Then, place your hand on the top of the club to hold it steady.
How to measure golf club?
To measure a golf club, start by laying it on a flat, horizontal surface, like a table or countertop . Then, turn the bottom of the club head so it's at a 60-degree angle to the surface you're measuring the club on. Finally, use a tape measure to measure from the end of the grip to the point where the bottom of the club head meets the flat surface. ...
How to measure club length?
Calibrate the club length measuring apparatus. Turn on the machine and move the grip support assembly to the left until it reaches the end of the apparatus. Put the calibration rod into the machine, resting the right end of the rod against the 60-degree sole plate of the clubhead support.
Which plane should golf clubs be measured on?
Clubs should be measured on a horizontal, rather than vertical, plane to get the most accurate results. ...
Where is the sole on a golf club?
The sole is the bottom of the club head. You may need to rest the sole against a plate to ensure it sits at the proper angle. Measure from the end of the grip to the end of the sole. Use a tape measure to find the length in inches between the end of the grip and the farthest point that the sole contacts the horizontal surface.
How to rock a golf club back and forth?
Ensure the clubhead rests against the clubhead support, with the sole touching the 60-degree sole plate. The grip should rest in the grip support. Gently rock the club back and forth to be sure it’s not being constrained and can move naturally.
How to read scale on a scuba diver?
Slide the grip support until it touches the grip, then read the scale. Move the grip support to the right until the butt plate is gently touching the end of the grip. Step back from the scale and read the digital value. ...
How to measure golf clubs?
This is the simplest method that you can use at home to measure your golf clubs. For this, you need a ruler of 48 inches or greater . You can use a measuring tape. However, the flexibility of the tape can hamper the entire procedure.
Is there a standard length of a golf club?
There is no standard length of a club in golf. So, club makers are free to make clubs that they feel are appropriate for a golfer. Here is what Tom Wishon, the founder of Tom Wishon Golf Technology, has to say- “There are no industry-wide standards for any golf club specification in the golf equipment industry.”.
How long should a golf club be?
According to USGA the length of a golf club should not exceed 48 inches. So, the length can be either 48 inches or lower. Within this limitation, you can get club sizes of any length depending on your height or style of play.
How many inches is a 5 wood club?
For 5-woods it was even lesser, just 41 inches. The reason behind the shifts in club length is the mindset of the golfers. Most golfers believe that longer shafts can provide more distance. So, manufacturers have taken the best opportunity out of this. They believe it helps them to sell more.
What size ruler do you need for golf club reading?
For this, you need a ruler of 48 inches or greater. You can use a measuring tape. However, the flexibility of the tape can hamper the entire procedure. For best readings use a golf club measuring ruler. Now, if you got the ruler in your hands, we can proceed. Follow these steps one after another: Step 1.
What is the best length for putters?
For putters. Analyzing the posture and wrist-to-floor measurement, 32-35” can be a good length for putters that most golfers will be comfortable with. Longer putters will cause several problems in your gameplay. It will restrict you from being close to the ball and miss targets in most cases.
Where is the ruler on a putter?
The ruler method can be used for putters. Instead of the heel, the ruler is placed beside the center of the putter. This means your ruler must be placed along the shaft to the ground. The ruler must be placed behind the club, and the final reading must be taken from the edge of the grip cap.
Where is the club length measured?
The club length is not measured to the middle of the face, it's measured along the shaft axis (or as close as you can come). The club sole should be square with the ground while measuring, but the imaginary point where the shaft would extend down to the ground is the start point.
What would happen if two clubs were measured for length?
If two clubs were measured for length, one measured from the playing position, and one measured the traditional way (i.e. like the picture above) then would the one measured from the playing position measure longer when it's measured the traditional way?
What Is Shaft Length?
Shaft length is the shaft’s raw length, which is connected between the clubhead and the grip. It acts like a lever and allows a player to hit the golf ball over a great distance by using the body’s rotation.
Shaft Length in Irons
The optimal shaft length in Irons can be determined by a set of measurements like arm length, player’s height, and swing posture. A tall player would not benefit by using a golf club designed for a short golfer.
Shaft Length in Drivers
The shaft length in drivers helps you determine how fast you can swing the golf club, along with the angle of attack and the club’s path. The standard length for the drivers is 44.5 inches.
