Golf-FAQ.com

how to prep the tip of a steel golf shaft

by Mr. Jaren Hirthe Published 3 years ago Updated 2 years ago
image

Step 1: Check the fit. Put the shaft into the hosel dry. If the shaft slides in easily, you’ll want to be a bit more gentle in your prep. If the shaft barely fits or doesn’t fit at all, you’ll need to remove more material. Step 2: Mark the shaft. Use a pencil or marker to indicate how much of the shaft will go into the hosel.

Shafts: Lightly sand shaft from tape to tip with 150 grit or finer sand paper to remove the polyurethane finish and all the paint. This operation is "prepping" the shaft and can be done by The GolfWorks (PREP). Step 4. The steel shaft tip should have a uniform satin or brushed appearance.

Full Answer

Should you tip your golf shafts?

In most cases, shaft tipping is done to steel iron and wedge shafts but occasionally is done in graphite shafts for woods and drivers as well. Lastly, tipping won’t do much to affect spin rates and launch angle — two popular misconceptions when it comes to trimming the lower end of a shaft.

What does tipping a club shaft mean?

“Tipping” or “tip trimming,” as it’s sometimes called, means trimming a club shaft from the clubhead end, not from the grip end where it’s most often cut. What’s the difference between True Temper Dynamic Gold and Dynamic Gold Tour Issue shafts? Ok, so what?

What percentage of golf shafts are trimmed?

About 90 percent of all fairway woods are trimmed on the PGA Tour. Woods are commonly tipped three to four inches. Tipping a golf shaft allows players to have more control over their club. It allows players to feel the proper flex and help control their ball flight trajectory.

What does tip trimming mean on a golf club?

“Tipping” or “tip trimming,” as it’s sometimes called, means trimming a club shaft from the clubhead end, not from the grip end where it’s most often cut. What’s the difference between True Temper Dynamic Gold and Dynamic Gold Tour Issue shafts?

image

How do you prepare an iron shaft tip?

0:445:50Golf Repair - How to Prep a Graphite Shaft Tip for Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow I typically use 180 grit sandpaper or 120 it's a little bit me this would be medium this wouldMoreNow I typically use 180 grit sandpaper or 120 it's a little bit me this would be medium this would be fun. And this ensures that we don't start to dig too far into the removal.

Can you tip steel shafts?

In most cases, shaft tipping is done to steel iron and wedge shafts but occasionally is done in graphite shafts for woods and drivers as well. Lastly, tipping won't do much to affect spin rates and launch angle — two popular misconceptions when it comes to trimming the lower end of a shaft.

What does trimming the tip of a golf shaft do?

Shaft tipping is when a club builder removes length from the tip section of a shaft, which is the end where the clubhead is installed. In most cases, tip trimming a shaft makes it meaningfully stiffer. It also increases torsional stiffness, known as “torque,” which is a shaft's resistance to twisting.

How do you remove tip weight from a graphite shaft?

0:122:14How To: Remove a Stuck Tip Weight from a Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipGonna create enough friction it's gonna grab the tip weight. And then you just pull it out thatMoreGonna create enough friction it's gonna grab the tip weight. And then you just pull it out that works well it takes a lot of time if you have to go through the steps of using.

Do you tip trim iron shafts?

Instead of stocking individual shafts for every club, the same shaft can be tip trimmed to fit any iron club. In additional to trimming the tip, you'll then need to trim the butt end, to achieve the final desired club length.

Does cutting down a golf shaft make it stiffer?

"Cutting more of the grip end will still stiffen the shaft a little bit, but only because in doing so you make the shaft shorter, and not nearly as much as when trimming more from the tip end."

How does tip trimming affect Flex?

0:301:51What Does "Tipping" Your Driver Affect? // True Temper SchoolYouTubeStart of suggested clipEnd of suggested clipYou know you can tip an inch half an inch inch and a half whatever you want and obviously the moreMoreYou know you can tip an inch half an inch inch and a half whatever you want and obviously the more you tip you're gonna affect stiffness and increase in tipnis there.

Does shortening a shaft make it stiffer?

A shorter shaft is typically stiffer than a longer one. Although a shorter golf club shaft tends to be firmer than a longer one, it is important to understand the changes trimming a shaft will make to a club before making such a permanent change.

How much can you tip a golf shaft?

The average length tipped on tour for drivers is near one inch. Some players do more though. Tiger Woods cut his driver shaft to 42.5 inches at one point in his career when using a True Temper X-100 steel shaft.

How do you install a shaft tip weight?

1:523:49How to Tip Weight a Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut a little bit on the inside of the shaft. And then insert the tip. Wait. You have some overflow.MorePut a little bit on the inside of the shaft. And then insert the tip. Wait. You have some overflow. So you'll need to get a paper towel.

How do I clean the hosel on my golf club?

Soaking the industrial strength cotton swab hosel brushes in acetone or mineral spirits and inserting into the club head hosels will clean out any oil or epoxy residue that may negatively affect the new epoxy bond during assembly. All brushes are threaded and can be used with the same universal wooden handle.

How do you make a golf shaft puller?

0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.

How much does tipping a shaft effect Flex?

In this model, the 1” tipping is not even a small percentage of the difference between the S and X flex versions of this shaft. We can see this clearly looking a the numbers. The butt stiffness of the shaft increased one tenth of a pound, the torque, three tenths of a degree.

Can you tip a taper tip shaft?

2:523:29Differences Between Taper Tip & Parallel Tip Iron Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipOr you can put a shim on the end of a taper tip shaft. And play that as well. So technically youMoreOr you can put a shim on the end of a taper tip shaft. And play that as well. So technically you could also play parallel and taper if you bore out the head or stand on the graphite.

How do you tip a graphite shaft?

1:0911:44The Purpose of Shaft Tipping - YouTubeYouTubeStart of suggested clipEnd of suggested clipSection we take away. The more we get into the more we expose this wider. Section from from here onMoreSection we take away. The more we get into the more we expose this wider. Section from from here on up. So we we take the soft part away we leave the stiffer part which is up in this butt. Section.

Does tipping change swing weight?

It will reduce the swing weight by five points but have no effect on the swing dynamics. This is a method to tweak clubs if you really know what you are doing and play on the Tour.

What Is Tipping A Golf Shaft?

Getting a golf shaft tipped is when the shaft is cut back (tipped) from the clubhead end, shortening the club and making the tip of the shaft stiffer.

How To Cut Golf Shafts?

If you’re asking yourself: “Should I tip my driver shaft?” It’s ultimately up to how experienced a golfer you are and if you think it can help add more control in your game .

Why is the shaft stiffer?

It allows players to feel the proper flex and help control their ball flight trajectory. Making the shaft stiffer helps lower torque and lessens a golfers chances of twisting the club at impact which usually results in bad shots.

How long should a driver shaft be tipped?

It is very common for PGA Tour players to have tipped driver shafts and fairway woods. The average length tipped on tour for drivers is near one inch. Some players do more though.

What happens if you cut a golf club from the butt?

If you cut a club from the butt end then you will make the club shorter and stiffer. If you cut too much length off and shorten the club too much, you will have it stiffer but you might lose distance as well.

What to use to scrape epoxy?

Heat and an old thin/narrow chisel (or even a strong enough flat head screw driver) can be used to scrape/pry out get out most of the old epoxy. Some builders will use a slightly undersized regular drill bit - just be careful - use low speed and low pressure. And then this can be used for a final clean-up. ...

Can you use water to reshaft a club?

If you use water make sure it's dry. Reshafting is the easiest and most idiot-proof part of club-making. As long as you have a matte tip, a clean hosel, and well mixed epoxy, it is incredibly hard to screw up. Quote.

Is acetone better than alcohol for cleaning shaft tips?

In fact, even that is generally overkill when it comes to cleaning up the shaft tip after prep. The one exception that I'm aware of is typically when the contaminates is a silicon based lubricant, that's when acetone is going to work much better than alcohol.

Can you use old sandpaper on steel?

Yeah, Just any old sandpaper for steel. I like 100 probably cause I always have some around. For 30+ years, I have scraped the paint off graphite shafts with a knifeblade. Never had a fail or breakage.

Can you sand graphite?

Depends how long you sand it? As has been said above, you really can't go too far with steel, and graphite you really just want to take off the clear-coat of the paint (unless you you need to remove some extra from the tip due to hosel insertion. It's all about creating the best possible bonding surface, and that not only includes abrading/removing anything "shiny", but also cleaning all dust/debris thoroughly with acetone and allowing it to dry.

Does alcohol help with epoxy?

Doesn't need to be , just use something to remove sanding dust and any oils that would hinder epoxy adhesion. Alcohol works just as well, some would even say better because it dries "cleaner".

Can you use water to sand a shaft?

For the most part, if you are doing a thorough prep all the way around the shaft, I'd reckon you could even use water, as long as you give it plenty of time to evaporate dry completely? The sanding should remove any lubricants/impurities, and you are really just removing any dust left over from the sanding?

How to clean a true temper shaft?

Clean off any corrosion on the shaft tip and you should be good to go. True Temper recommends using a fine grit sandpaper, not coarse. We are sort of splitting hairs here on all these details though.

What grit to use for graphite?

I use a piece of 80- grit folded in half to make a hard edge sort of like the razor blade method for graphite and I only go straight down the shaft. For steel I use 80-grit and go to town on it.

How much cleanup for graphite?

80 for steel. Razor blade followed by 220 cleanup for graphite new & pulled shafts.

Does epoxy stick to chrome?

Trying to understand the connection a little better. As long as we're splitting hairs, I don't think that the epoxy sticks to raw steel better than it does to chrome. Its that the chrome isn't integrally part of the steel shaft, its just cosmetically applied. Therefore the epoxy, while sticking to the chrome just fine, can rip the chrome right off the steel under torsion, impact, etc. I could be totally wrong about this.

Does Ping shaft have chrome?

The only steel shafts I've ever seen that had no chrome on the tip are Ping branded shafts. The epoxy sticks to raw steel better than chrome.

Can you use coarser sandpaper to cut through epoxy?

It is just faster and that is the only advantage. The person who said that a coarser surface gives you a better bond, just doesn't understand how epoxy works. You are far better off to use a finer grit sandpaper.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9