Procedure to remove the Sportwagen or Golf wagon instrument cluster Gently pull on the trim in front of the cluster to release it and access the two screws that hold the cluster.
Full Answer
How do you remove a VW Golf dashboard?
1:5112:35VW Golf Mk4 Dashboard Removals - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's just a matter of pulling off. So well snap pull-off pull-off use a remover tool for your oneMoreIt's just a matter of pulling off. So well snap pull-off pull-off use a remover tool for your one then once you pull that off it allows you to pull these ones. Off. These ones up.
How do I remove dashboard instrument cluster?
0:403:52How to remove an Instrument Cluster | GM Dashboard Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd stick it behind the dash. And pop this. Out you're going to go along the top and feel for anyMoreAnd stick it behind the dash. And pop this. Out you're going to go along the top and feel for any clips there. And just pull the dash trim piece towards. You then take the dash piece out.
Can you remove the instrument cluster?
Lower the front slightly and pull towards the steering wheel. Once removed it will expose a single screw to the left of the steering column. Remove screw to the left of steering column. The entire dashboard may now be removed by pulling from around cluster, radio and steering column.
How do I remove instrument cluster connector?
1:163:25How to disconnect instrument cluster wiring harness connector for ...YouTubeStart of suggested clipEnd of suggested clipAnd here's the tricky. Part it's disconnecting the cable that goes back to the wiring harness.MoreAnd here's the tricky. Part it's disconnecting the cable that goes back to the wiring harness.
How do I change my instrument cluster?
1:1110:57How To Remove Or Replace GM Truck Instrument Cluster Dash PanelYouTubeStart of suggested clipEnd of suggested clipTo help things out a bit note that with the shifter all the way down it's gonna be in first gear. SoMoreTo help things out a bit note that with the shifter all the way down it's gonna be in first gear. So you will need to have your foot on the brake. So you don't roll away.
Can you just replace instrument cluster?
Changing the instrument cluster is a relatively easy process and can be attempted by anyone who is familiar with a basic set of tools. There are a few things that can go wrong but the steps are still considered simple by most mechanics. Put aside roughly an hour to an hour and a half for this job.
Does a used instrument cluster need to be programmed?
You can get a cluster from a wreckers and it will be plug and play. Miles and hours are stored on the cluster only so you need to have the new cluster programed to the milage on your original cluster if you want.
Can you put a different instrument cluster in a car?
All you need to do is: Remove the instrument cluster from your dash. Either have your instrument cluster repaired or buy a new one. Install the repaired or new instrument cluster in your dash.
How do you remove gauges?
1:173:25How to safely remove needles from gauges. - YouTubeYouTubeStart of suggested clipEnd of suggested clipSort of slide the spoon in underneath each side. And then applying equal pressure to either side ofMoreSort of slide the spoon in underneath each side. And then applying equal pressure to either side of the needle. Just pry it off this way. There it goes voila that's how you remove the needles.
How do you remove a gauge cluster on a 2004 Silverado?
0:123:05How to Remove and Repair A Chevy or GMC Instrument Cluster (2003 ...YouTubeStart of suggested clipEnd of suggested clipOn shift the gear lever to the lowest. Position and tilt the steering wheel all the way. Down thisMoreOn shift the gear lever to the lowest. Position and tilt the steering wheel all the way. Down this allows the front trim panel to be removed once it is detached.
How do I reset my GM instrument cluster?
Push and release the Sel/reset button button 3 times repeatedly. The instrument cluster begins its self-test. Each successive press of the Sel/reset button initiates a new cycling of all the gauges. To end, turn the ignition switch to OFF, or vehicle speed exceeds 1.5 mph.