How to Install a Shaft in a Golf Club
- Step 1. Remove the old shaft. It can be done by melting the glue, or epoxy, that holds the shaft to the head of the club.
- Step 2. Cut the shaft to the proper length, depending on what club you are modifying. There are websites that can help...
- Step 3. Roughen the tip of your new shaft before inserting it into the hosel of the club...
How do you replace a golf club shaft?
How To Re-Shaft Your Steel Golf Clubs
- Carefully clamp the shaft into a vise using a Shaft Vise Clamp. ...
- When removing steel shafts from clubheads, use a torch to heat the hosel. ...
- After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head. ...
- Using a wire brush remove excess epoxy from the inside of the hosel.
When to reshaft your golf clubs?
What is a golf club shaft?
- Steel – There are two types of steel shafts: stepped steel and rifle steel. ...
- Graphite – These types of shafts are less durable and typically more expensive.
- Multi-material – This type of shaft is a combination of steel and graphite shafts.
How much does it cost to reshaft a golf club?
So, how much does it cost to reshaft a golf club? To reshaft a golf club, you’re likely to spend between $20 to $200 per club. The cost of reshafting your golf clubs will vary greatly depending on where you go to have it done. The cost will depend on the cost of the labor, the number of clubs, and the cost of the new shafts.
How much does a golf club shaft replacement cost?
With a vast array of shafts to choose from, there are options to fit every budget. For the budget-conscious golfer, replacement shafts can start at $30 for no-frills, entry-level quality. For players who are willing to pay a bit more, there are plenty of options lying between $50 to $200, for shafts in all five flex categories.
Can you change golf club shafts?
Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How do you install a golf club shaft?
5:117:44SHAFT INSTALL Steel - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce the ferrule is in position take the head and push the ferrule into its final position tap theMoreOnce the ferrule is in position take the head and push the ferrule into its final position tap the butt of the shaft on a hard surface to ensure the shaft is installed to the bottom of the hosel.
How much does it cost to change a shaft on a golf club?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
How do you Reshaft a golf club at home?
2:3522:36GOLF CLUB BUILD - How to reshaft your irons Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heatMoreUp the house'll. Pull the shafts you don't need a shaft puller. Anything like that you can just heat them up and twist them off because it's a steel shaft.
Is it easy to Reshaft irons?
Golf irons can be a bit easier to reshaft than a driver. If you are reshafting with steel irons, it is usually pretty straightforward. However, you will need the proper tools and space to complete this project.
How do you Reshaft a driver at home?
0:144:53How To Reshaft Golf Clubs - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere just as the pocketable bandha looks better with it as you can see two of ours also prep the tipMoreHere just as the pocketable bandha looks better with it as you can see two of ours also prep the tip taken basically the paint off the shaft that way to here to the epoxy.
Is it worth it to Reshaft irons?
Reshafting is just one way to keep your clubs performing at a high level. You can also benefit from regripping your clubs. Replacing worn-out golf grips can help make your clubs feel new again. Adding the right shaft to your favorite clubs can get you back on the course and working toward a new personal low round.
Can you put a new shaft on a driver?
Replacing your old shaft can be a relatively painless process for you or your local repair shop. If your favorite old driver seems to have run out of quality hits, you might want to refresh it by adding a new shaft to the club.
Can you put any shaft in a driver?
Yes, most golf Driver shafts are interchangeable. Golf driver shafts can be replaced as long as the new shaft is the same length and made by the same brand of golf club.
How much does it cost to get a driver Reshafted?
The cost of reshafting a golf driver is between $15 and $45 USD. The labor cost of reshafting is usually around $20 USD. However, the actual overall cost can also depend on the materials used as well as the type of grip and shaft you are looking at.
Can you put new shafts in irons?
Can golf irons be reshafted? Yes, just like other types of golf clubs, golf irons can also be reshafted using a golf repair service.
How do you pull a golf shaft?
6:2514:27pulling a golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I like to do is I like to pinch. Down. And then pull back pinch down and then pull back. AndMoreAnd I like to do is I like to pinch. Down. And then pull back pinch down and then pull back. And this way you don't scrape a shaft.
How to remove a golf club shaft?
Step 1. Remove the old shaft. It can be done by melting the glue, or epoxy, that holds the shaft to the head of the club. Use a blowtorch or a heating gun for this purpose. Aim it at the hosel--the connecting part of the head--until the epoxy softens and you can easily remove the shaft.
How to put on a golf grip?
Place double-sided tape on the shaft where the grip will be placed and soak it with grip solvent. Pour a small amount inside the grip, then swirl it around until it is completely covered. Pour out the remaining solvent onto the double-sided tape, then put on the grip, making sure it is firmly set on the butt of the club.
What to use to insert graphite shaft?
If you are inserting a graphite shaft, it would be best to use a belt sander because you can easily damage it by using sandpaper. Also, rid the residue of the old epoxy for the hosel by using a wire drill bit.
Series Navigation
Using epoxy to install a shaft is not a difficult task, but I think some people get a bit confused when dealing with different types of golf clubs. Putters are fairly easy to do, but when re-shafting irons and woods, we have to install the ferrule as well, which is a bit confusing to the novice.
Series Navigation
Hey!! I'm Zach, the founder of The DIY Golfer. I created this site in 2015 while playing D1 collegiate golf to help myself understand the game of golf better and improve as a player. Fast forward a few years, and it has become much more than a journal.
How to fix a club head that is stuck to the shaft?
Step 1. Scrape off the ferrule at the bottom of the club head's hosel with a utility knife. Place the club into a shaft clamp to hold it in place while you work on the head. Use a heat gun to heat up the area around the hosel to soften the epoxy glue that connects the shaft to the club head.
How to remove epoxy from golf club?
Remove the club from the shaft clamp and tap the butt end of the grip on the floor to push the shaft all the way into the head. Wipe down the hosel with a soft cloth to remove any epoxy residue. Let the epoxy dry for several hours before using the golf club.
What is the hosel on a golf club?
The hosel is the junction point between the head and the tip of the shaft. Check the size with a shaft identification gauge if you cannot find it on the label.
Can you replace a golf club shaft yourself?
It's usually best to consider having shaft replacement done by someone who knows what they are doing. Instead of paying the pro shop the next time you need to change a golf club shaft, save money by doing it yourself at home. Make sure your replacement shaft is the same size as the original or it might not fit inside the club head's hosel.
Step 1
Remove the old shaft. If there is an existing or broken shaft on the club, the first step is to remove it. You need to break down the epoxy bond between the shaft and the head. To do this, you need to provide even heat to the hosel (where the club head attaches to the shaft). This can be achieved by using either a torch or a heat gun.
Step 3
Prep the new shaft. Measure the depth of the hosel and then mark this depth on the shaft. Note: When prepping the new shaft, always follow the manufacturer's recommended tip trimming guidelines. Should you be installing a graphite shaft, be careful that the graphite doesn't splinter, as this will weaken the shaft.
