The necessary materials available for refinishing a set of golf clubs are some paint and varnish remover, waterproof glue, epoxy filler, a soft cloth, masking or duct tape, wiping stain, hard wax, toothpicks, aerosol spray varnish or lacquer, and black or white metal paint.
What are the best golf clubs to buy?
What to look for:
- name brand clubs (TaylorMade, Titleist, Callaway, Cobra, etc) that are 2-10 years old
- complete set (driver, fairway wood (s), hybrid (s), irons, wedge (s), putter, bag.). The more clubs, the better.
- decent condition. If the club faces are completely worn down, then pass. You want at least the iron club faces to be in decent shape. ...
Where to buy TaylorMade golf clubs?
These combinations are determined by three factors:
- Distance
- Height
- Face slots
Where to buy used golf clubs?
When the grooves get smoothed out over time, you’re reducing friction between the golf club and the ball, and you’ll lose spin and control around the greens. If your golf ball is coming out like a knuckle ball, and the grooves have been flattened out over the years, a new wedge can help you hit those low spinners once again.
Who buys used golf clubs?
Woods then made the turn in 2001 and won the Masters, becoming the first to hold all four professional major golf championships ... confidence that these clubs were used by Tiger Woods during ...
Can old golf clubs be refurbished?
GOLF CLUB REPAIR: REFURBISH VS REPLACE If a standard cleaning won't do, a golf club refinishing can help return your clubs closer to their original, polished state. “It can also touch up those little nicks and dings that occur during a round,” DICK'S Sporting Goods Associate Nick Jendrejeski says.
How do I restore my golf clubs?
Vinegar and Lemon Juice. Similar to Coca-Cola, the acidity of Vinegar and Lemon Juice works to break down and remove rust. A quick soak can easily loosen surface rust and allow your club to be cleaned using a brush.
How do I make my golf clubs look new again?
Mixing up warm water and mild soap. Fill the bucket with a not-so-hot water. ... Submerge the club several times for 5 to 10 minutes. ... Remove and scrub the clubheads. ... Wash the club with cold water. ... Apply steel of chrome polish. ... Keep the bag in a safe place.
How do you refurbish a golf club face?
0:004:48How to Recondition the Club Face - DIY Golf Club Restoration - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo i'll throw some masking tape on i also have a little bit of aluminum tape which is a little moreMoreSo i'll throw some masking tape on i also have a little bit of aluminum tape which is a little more durable than just masking tape i'll probably put that just on the edges.
Can you buff out scratches on golf clubs?
Deeper scratches are difficult to fix, and this is why most golfers won't bother removing them. To remove deep scratches, try using a buffing compound on a soft toothbrush. Rub the brush against your club in a forward and backward motion. This is the safest method and it shouldn't ruin your club.
Can you use wd40 to clean golf clubs?
Not An Effective Way To Clean Clubs If you spray the oily substance directly onto dirty golf clubs, it will loosen the top layer of dirt, but it does not remove the gunk living deep in your grooves. Therefore, you still need to give them a proper scrub to remove any debris build-up over the long term.
How do professional golfers clean their clubs?
0:211:53How to Clean and Store Your Golf Clubs - YouTubeYouTubeStart of suggested clipEnd of suggested clipTake your first Club. And dunk the head in the bucket of water for a few seconds remove. It and wipeMoreTake your first Club. And dunk the head in the bucket of water for a few seconds remove. It and wipe it off with the towel. Make sure all the debris has been removed from the grooves cleaning.
Can you Regroove clubs?
It's necessary to regroove your clubs on a regular basis to improve your backspin performances. This particular model can be used to regroove U grooves, V grooves as well as square grooves. It's also USGA rules and regulations compliant.
How do you clean old golf clubs?
Mix warm water and 2 teaspoons of dishwashing liquid or soap into a bowl or a bucket (depending on how many clubs you need to clean). Dip your soft-bristle brush or toothbrush into the mixture and carefully scrub your club head, making sure that it doesn't get too wet.
How do you restore old irons?
2:2612:33How to restore the chrome finish on a set of golf club irons - YouTubeYouTubeStart of suggested clipEnd of suggested clipA good swill. Although to remove the plating it doesn't remove the rust. So here we're going into aMoreA good swill. Although to remove the plating it doesn't remove the rust. So here we're going into a tank of hydrochloric acid which is going to dissolve the rust off and leave us with clean rust free
Can you get irons refinished?
Founded by Jim Kronus, The Iron Factory began as the first and only golf club iron refinisher in the United States. Since then, we have perfected the process of repairing, rebuilding, and refinishing over a million clubs for both professional and amateur golfers.
What is the best paint for golf clubs?
Enamel paint and preferably epoxy-based enamel paint is highly recommended. Enamel is oil-based, adheres easily to metal surfaces, is highly durable, and, has a gloss finish. Acrylic Paint. This paint is water-based and drys quite quickly and is cheaper than enamel paint.
How do I make my golf clubs shiny?
How Do I Polish Golf Clubs?Cleaning the clubs thoroughly before a good polish. ... Gently work the hot water and soap over the face and back of the golf club with a toothbrush or medium-bristled brush. ... Dry the clubs with a towel or rag. ... Apply any metal polish or car wheel polish to the golf clubs.More items...
Will Coke remove rust from golf clubs?
Pour the Coke into the bottom of the bucket on the club heads. When the Coke settles down, you will want it to soak for several hours. Letting the golf clubs soak for at least four hours or so will give the Coke time to work cleaning the rust off the clubs without you having to scrub them.
How do you clean old golf clubs?
How To Clean Your Golf IronsDip the iron in your lukewarm water.Scrub the entire head and face with your brush - pay special attention to the grooves.Use your towel to wipe off all dirt and debris.Dip the iron back in your water.Dry off using your towel.Repeat 1-5 if you still see dirt in your grooves.
What is the best paint for golf clubs?
Enamel paint and preferably epoxy-based enamel paint is highly recommended. Enamel is oil-based, adheres easily to metal surfaces, is highly durable, and, has a gloss finish. Acrylic Paint. This paint is water-based and drys quite quickly and is cheaper than enamel paint.
How to replace a golf grip?
With the alignment pattern facing upwards, push the grip to allow the shaft to enter through it smoothly. Ensure that the end of the shaft is firmly attached to the end of the grip. Finally, align the grip with the pattern on the clubface and let the grip dry.
How to remove old grip from a golf cart?
The first step is to cut off the old grip from the top downwards using a blade or any suitable cutting equipment. If your shaft is made of graphite, be careful not to cut off the graphite fibers. Make sure you protect your hands with protective gear, so the blade doesn’t cut you. Gently remove the old grip from the shaft.
How to clean a grip?
This process requires you to cover one end of the hole with your hand and pour the solvent through the opposite hole. Shake the grip with the solvent to ensure that it is applied generously . Use a tray to catch any excess solvent that may spillover.
What do you need to know before installing a shaft?
Before installing the shaft, you need to prepare it for installation. Use the correct measurements to cut it to the required length. Some shafts are made of steel, while others are made of graphite. If you purchased the steel one, then using a sandpaper scrub around the tip to make it a bit rougher.
What residue is left in hosel after shaft removal?
What remains inside the hosel after removing the shaft is epoxy residue. If epoxy remover isn’t readily available, you can use a round file to remove the residue. Once done, use propanone or acetone to remove any grease residue.
Where to put epoxy on a golf club?
Apply epoxy at the end of the clubhead where it goes inside the hosel. You should also apply the epoxy inside the hosel. Once you are done, gently push the shaft into the club head’s hosel.
Can you refurbish a golf club?
Refurbishing a golf club depends entirely on the parts you want to refurbish. Some parts and accessories vary depending on quality, size, and material used. If you want the best quality, you will probably have to part with more money.
How much does it cost to refinish a golf club?
Once your club is clean, you may want to give it a fresh new finish. Professional club finishing can be expensive. You can expect to pay around $50 per club to get them professionally refinished. This can be a fun way to bring life back into a beloved or special set. However, the cost can be price prohibitive.
How to get rust off golf clubs?
This can be a good place to start for most clubs. With a simple mixture of soap and water, you do not need to worry about damaging the club. After a brief soak , use a small brush like a toothbrush to try and remove any rust. This works best if the rust buildup is not extreme.
How much does it cost to regroove a wedge?
Wedges and irons can have their grooves professionally regrooved. This service ranges in price but usually is around $20 per club. This is the best way to restore a wedge to its original performance. However, it relies on slightly increasing the size of the grooves each time and can only be done o many times.
What to put on golf clubs to prevent rusting?
Wax. This may sound strange but a thin coat of wax on a golf club can prevent it from rusting. Wax is obviously slippery, which makes it unwise to put on places where you want friction, like a wedge face. However, it is very helpful in protecting the finish on shafts and golf heads.
Can a Cobra wedge rust?
Cobra Trusty Rusty Wedge. Leaving you’re club outside or even storing it in unfavorable conditions can result in rust. Contrary to popular belief, a little rust is not the end of the world. For some used clubs, especially wedges, some rust may even be beneficial. Made famous by Cobra’s Trusty Rusty wedges, rust can actually increase ...
Can steel wool be used on golf clubs?
Steel wool and wire brushes can be helpful in removing surface rust. However, used improperly these products can damage the surface of a golf club. Be sure to use a wire brush made of a material less strong than the material of your club. Likewise, starting off with ultra-fine steel wool will ensure you do not scratch or damage your clubs.
Does rust on a golf wedge increase spin?
Made famous by Cobra’s Trusty Rusty wedges, rust can actually increase the friction on the surface of a wedge and increase spin. If you are trying to make the clubs look newer, there can be several strategies for removing the rust that has built up.
What is refinishing golf clubs?
Refinishing golf clubs is a fairly simple process that will give you an opportunity to try new things with old clubs. Whether you want a new look on your putter head or a different flex on your shaft, refinishing clubs at home is a great way to try out new technology.
How to remove paint from golf club?
The first step is removing the current finish and any paint on the clubhead. This may be accomplished by soaking the clubhead in Coke for two to three hours, then wiping the finish off. Apply additional solvent to difficult spots. Once the finish is off, you can repaint the printed areas with any color of acrylic paint you desire and apply a new finish to the entire clubhead.
How long does it take for a golf club to dry?
If you will be refinishing multiple clubs, the process might take several days--clubs need to dry for about 12 hours at different stages of the process.
How to twist a clubhead off?
Once the epoxy begins to break down, you can twist most clubheads off by hand. When the shaft is removed, clean out the hosel, then apply epoxy to the new shaft and the interior of the hosel. Insert the shaft into the hosel and let dry overnight.
Sole and Toe Refurbishment
Before you complete your purchase, you may request additional refurbishment services available on any used Irons or Wedges. We grind the sole and remove any damage and scratches. We then buff the area to bring back the shine. Please note that all orders that include refurbishment must be placed by phone.
Club face Refurbishment
Before you complete your purchase, you may request additional refurbishment services available on any used Irons or Wedges. We polish the face and remove many of the cosmetic damage and scratches. We then buff the area to bring back the shine.
ADDITIONAL SERVICES
In addition to our refurbishment programs, we offer many additional customization services for your clubs. When your getting your clubs serviced, you might want to add on these services to increase the life of your new club.
What tools are needed to refinish golf clubs?
A small Philips-head screwdriver, a shallow pin, a small natural-bristle brush and an artist’s brush are all the tools needed to complete the process.
What is golf club refinishing?
Refinishing clubs can help give them new life. When it comes to a golfer and a set of clubs usually that golfer is very attached to them, sort of like a newborn baby is close to a blanket or similar to a teenage couple being emotionally involved with each other on a different level.
How long does it take to refinish a golf club?
Refinishing a set of golf clubs is very simple, it takes only a few days, and it is well worth the effort. After it’s completed one time or two it will become even easier to accomplish the next time and the time after that. All golfers know the two most important factors when on the golf course are to place a great score on the score card and to look stylish while giving your friends and/or opponents a nice, friendly smackdown on the course after 18 or more.
What to do with holes in wood for golf clubs?
If there are holes or dings in the wood, fill them with epoxy filler only . If wood or steel fillers are used, it can change the dynamics of the club's weight and swing capabilities. After that, the refinishing process is complete, and the clubs will almost appear as if they were just purchased.
Why are my screws stripped?
Over time, the screws can be stripped due to normal wear and tear.
What are the two most important factors when on the golf course?
All golfers know the two most important factors when on the golf course are to place a great score on the score card and to look stylish while giving your friends and/or opponents a nice, friendly smackdown on the course after 18 or more . Sorry, the video player failed to load.
Is a golfer attached to a set of clubs?
Overview. When it comes to a golfer and a set of clubs usually that golfer is very attached to them, sort of like a newborn baby is close to a blanket or similar to a teenage couple being emotionally involved with each other on a different level. A golfer never wants to part with a quality older set of clubs, especially if they normally work well ...
