How to remove gas tank from club car golf cart?
How to remove the gas tank from Club Car golf cart. Keep the Forward/Reverse switch and the neutral lockout in Neutral and Service positions respectively. Adjust the fuel shut-off valve to the OFF or closed position. Start the engine and keep it running so that the fuel in the fuel lines, fuel pump ...
How do you remove the governor on a golf cart?
1 Loosen the nut attached to the governor arm with a 7/16” wrench to turn the shaft. 2 Push the governor arm to the back of the cart and grasp it with your hand. 3 Turn the governor shaft in the counter-clockwise direction until it cannot be turned further. 4 Retighten the nut and let go off your hold on the governor arm. More items...
How to replace the gas pedal on a golf cart?
Raise the seat and take off the cushions covering the engine. In newer model carts, you may have to remove the seat screws for raising the seat. Remove the screws present behind the seat on the black plastic cover as well. Locate the thick cable connected to the gas pedal and follow it to trace its connection at the other end.
How to bypass the governor on a Yamaha G1 golf cart?
The bypassing can be done by carrying out a zip-tie action on both the governor arms. The following methods show you how to adjust the governor on your Yamaha G1 golf cart.
How do you take a golf cart body off?
1:4913:38How to Remove & Install Club Car Precedent Golf Cart Body - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis body push it up before we can pull the body. Off. Once you have the body unclip you can nowMoreThis body push it up before we can pull the body. Off. Once you have the body unclip you can now bring it. Forward. So in order to remove this cowl there's going to be five bolts.
How do you change the body on a EZ GO?
6:569:35EZGO TXT Body Removal | How to Remove Golf Cart Body | Episode 1YouTubeStart of suggested clipEnd of suggested clipAcross the backyard you've got four little round tabs these tabs have to be pried out and then underMoreAcross the backyard you've got four little round tabs these tabs have to be pried out and then under each one is a 7/16 bolts we'll take those out and get started we're just about done now.
What year is a G2 Yamaha Golf Cart?
Yamaha Electric & Yamaha Gas Golf Cart Serial Numbers:Yamaha G1 to G11Yamaha's Longest Running Cart Model. The G-Series.JA2-000001G2 GAS1988J55-000101G2 GAS1989J55-100120G2 GAS199084 more rows
How do you take the bumper off a Yamaha golf cart?
0:555:14Armor Bumper for Yamaha® Drive | How to Install Video - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's two bolts that hold the bumper on to the frame. You're going to use ten millimeter socketMoreThere's two bolts that hold the bumper on to the frame. You're going to use ten millimeter socket and remove. These. Using a 17 millimeter socket.
How do I remove the front of my EZ Go golf cart?
1:442:57EZGO RXV Front Cowl Removal How-To - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay now that we got the two bolts on the side before out across the top we just grabbed home toMoreOkay now that we got the two bolts on the side before out across the top we just grabbed home to this front Cal it pull it on out keep in mind here. And on the other side is a little clip.
How do you remove the rear body from a Club Car DS?
3:147:18VLOG #10 Club Car DS body removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipBody is to use a number three phillips on the forward reverse handle remove those bolts and pull theMoreBody is to use a number three phillips on the forward reverse handle remove those bolts and pull the handle. Out. Then the charger receptacle use the number two phillips.
What is the difference between a Yamaha G2 and G9?
The later G9 model is a virtual clone of the G2 except the G9 has a band of rubber trim around the dash compartment instead of the aluminum trim found on the G2 model. The serial number has a prefix that designates the model, starting with a 'J' followed by 1 more letter and 1 number, or just 2 numbers.
What is the difference between Yamaha drive and drive 2?
In 2017 Yamaha introduced the current model, the Drive2. The easiest way to distinguish the difference would be the White Yamaha Name on the side panels as opposed to the black Yamaha on the G29s and to look for the rear body being seperated into 3 different components.
What G model is my Yamaha golf cart?
Usually found under the seat, under the driver side glove box area or on the chassis towards the rear of the golf cart. Under the bumper area usually. Once you have located this you can use the chart below to cross-reference those numbers and determine the year and model of your Yamaha Golf Cart.
How can I make my Yamaha Golf Cart faster?
0:005:15Yamaha G29 Drive Golf Cart Governor Adjustment - MORE SPEED!!YouTubeStart of suggested clipEnd of suggested clipItself by tightening this nut down you're putting more pressure on the spring. So that the governorMoreItself by tightening this nut down you're putting more pressure on the spring. So that the governor has to work harder to pull back on the throttle.
How can I make my Yamaha G29 golf cart go faster?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you take the governor off a Yamaha gas golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
How to drain gas in a golf cart?
You can drain the gas tank of your golf cart using a simple siphoning action. This becomes essential if you plan to clean the tank. The siphoning can be done using a hose and air blow gun in an EZGO cart. Insert a hose down into the fuel tank as far as it will go.
How to remove gas tank from 1987 G2?
The steps given below will guide you on how to remove the gas tank from the 1987 Yamaha G2 golf cart. Remove the engine and seat from the golf cart. Remove the three bolts holding the fuel tank in place. Unscrew the knob present at the bottom of the tank. This helps to detach the fuel line from the fuel tank.
How many gallons of gas in 1992 Club Car?
The 1992 Club Car gas tank has a capacity of seven gallons. However, you should get started with six gallons if your cart has a sled engine to avoid fuel leakage through the vented cap.
How to get gas out of a gas tank?
Stick a five-foot-long 5/8-inch heater hose into the gas tank. Make sure it goes down as much as possible. Place a catch pan on the floor. Cover the opening of the gas tank using a rag. Insert an air blow gun into the tank through the rag. Push the air inwards until the gas begins to flow out of the hose.
How to collect drained gas from a gas tank?
Place a rag over the opening of the tank and a catch pan on the floor to collect the drained fuel. Blow air into the tank using the air blow gun until the gas flows downwards through the hose. Collect the drained fuel in the catch pan or any other vessel that has been approved for this purpose.
How to get rid of water in gas tank?
Put some water and cleaning agents into the tank. Use the air flow gun once again to circulate the cleaning agents to all parts of the gas tank. You may need to run the air for about 20 minutes. Pump out the water to get the tank dry. Use simple green or shop vac to get rid of the water that doesn’t get pumped out.
Is the Taylormade M4 driver adjustable?
Is the TaylorMade M4 driver adjustable? Yes, the TaylorMade M4 driver is adjustable. It’s possible to have twelve different options for the loft, lie angle and face angle, including the standard...
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
What is a golf cart governor?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
Can you remove a golf cart governor?
It doesn’t take much time or skill to remove a golf cart governor. With some basic mechanical expertise and general-purpose tools, you can do this yourself. The process is more or less the same in all golf carts.
How to put a car engine back together?
This will help you put the engine back together. Start by unscrewing the top portion which consists of the air filter, carburetor and the pieces around them. Unscrew the valves and the fuel pump next. Afterward, disconnect the rest of the engine pieces, including the crankshaft with the connecting rod.
How to deconstruct a car engine?
Strip the engine down to its basic components. Use an adjustable wrench to remove the bolts and a screwdriver to remove the screws. Take photos of the deconstruction of the engine with a digital camera. This will help you put the engine back together. Start by unscrewing the top portion which consists of the air filter, carburetor and the pieces around them. Unscrew the valves and the fuel pump next. Afterward, disconnect the rest of the engine pieces, including the crankshaft with the connecting rod.
Does a Yamaha golf cart break down?
Just like cars and motorcycles, Yamaha golf cart engines break down after extensive use. An engine rebuild kit is available for Yamaha golf carts, allowing you to replace the parts that need replacing when the engine fails.
