Remove the rear wheel of the golf cart. Take off the brake drum from its place. Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring.
Full Answer
How to remove brake drum from a golf cart?
Then fix the arms of the puller firmly along the outer edge of the drum and keep tightening until the central drum comes off. Removing the brake drum from a golf cart requires quite a handful of tools. Apart from the above list, you must also keep some water and a fire extinguisher handy in case there is a fire from the acetylene torch set.
How do you fix an EZGO TXT brake drum?
To fix an EZGO TXT brake drum, follow the process below. First remove the cotter pin in the centre of the castle nut. Next make use of a fifteen-sixteenth wrench and pry out your castle nut just so that it is loosened, not entirely out in your hand. Use a 3/4 th wrench to break out your lug nuts and then use a carjack to hold up the wheel.
How do I remove the rear brake drum from the hub?
If you are only able to pull out the drum from its hub, then it is definitely an issue of ridge formation. For the easiest method, look out for a rubber grommet at the back end of the braking assembly. Remove the rubber Grommet from the rear end of the braking assembly. Using a screwdriver, push into the hole of the automatic adjuster to unlock it.
What happens if the brake drum gets rusted on the cart?
The brake drum can get rusted on the cart, in which case it will be almost impossible to get it out. It is better to keep a lookout for such possibilities. A ridge can form over the outer portion of the rotor due to continuous start and stop.
How do you remove the brake drum on a golf cart?
How to remove brake drums on a golf cart?Remove the rubber Grommet from the rear end of the braking assembly.Using a screwdriver, push into the hole of the automatic adjuster to unlock it.Next insert a second screwdriver to rotate the lock wheel.Then safely open the drum.
How do you remove drum brake drums?
1:516:48How to Remove a STUCK Drum Brake - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd don't be afraid to hit this hard so now as you're trying to take this off you're trying to doMoreAnd don't be afraid to hit this hard so now as you're trying to take this off you're trying to do like a wiggle back and forth motion as you're pulling. So I'm pulling and wiggling it back and forth.
How do you separate drum brakes from hubs?
0:122:11HOW TO Separate the Hub from the Drum - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhen you're pressing on it. And then you stand it in the. Press. Sometimes these come out reallyMoreWhen you're pressing on it. And then you stand it in the. Press. Sometimes these come out really hard too they'll really jack up the press and then a little release on the press.
How do you remove and replace drum brakes?
5:0122:00The ULTIMATE Guide on How to Replace Drum Brakes - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd we're going to hit both sides of the drum. You want to use a good amount of force. And make sureMoreAnd we're going to hit both sides of the drum. You want to use a good amount of force. And make sure you don't hit those studs by mistake. I can feel coming loose. Give it a little wiggle.
How do you remove drum brake screws?
0:052:00Rotor screw removal tip trick when held on with screws for Drums tooYouTubeStart of suggested clipEnd of suggested clipThis is a impact driver it has a Philips bit on it. And you hammer on it and it will take the screwsMoreThis is a impact driver it has a Philips bit on it. And you hammer on it and it will take the screws off so I recommend using this. It's a little practice you can use a hammer.
What tools are needed to change drum brakes?
You'll need a drum brake retainer spring tool and a pair of drum brake spring pliers. These can often be purchased as a set. You'll also need simple tools like a hammer, pliers, and other assorted hand tools to get everything apart.
How is the brake drum fastened to the wheel hub?
0:192:36Drum Brake System | Autotechlabs - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe friction between the lining and the drum is what makes the wheels to slow. Down hold down springMoreThe friction between the lining and the drum is what makes the wheels to slow. Down hold down spring holds the brake shoes towards the back plate.
What is the biggest disadvantage of the drum brake system?
Drum brake disadvantages Excessive heating can happen due to heavy braking, which then can cause the drum to distort, and thus cause vibration under braking. Under hard braking, the diameter of the drum increases slightly due to thermal expansion, the driver must press the brake pedal farther.
How do you compress drum brake pistons?
1:273:12How to compress Brake Pistons on your car - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou basically just twist this clockwise. And it is in fact compressing the piston. So without aMoreYou basically just twist this clockwise. And it is in fact compressing the piston. So without a camera i would do this with two hands.
Why can't I get my brake drum back on?
A common problem when rebuilding rear drum brakes is that the brake cylinder has too much air or fluid in it causing the brake shoes to be pushed too far out. Then the brake drum won't go back on as you experience.
How long does it take to change drum brakes?
about two hoursOn average, replacing a pair of drums and shoes takes about two hours from start to finish. However, if you need to replace other components as well, it can take longer. Since drum brakes last so long, it's a good idea to replace the wheel cylinder, adjuster, and springs when you replace the drums and shoes.