How Do I Remove the Shaft of a Golf Club?
- Step 1. Place the shaft, or what remains of it if it is broken, in a vise parallel to the floor. Secure the shaft in the...
- Step 2. Apply heat evenly to the hosel for about a minute, using a heat gun or heat torch. This will break down the...
- Step 3. Remove heat from the hosel and twist the club head counterclockwise. It should...
Full Answer
How do you replace the shaft on a golf club?
Steps to Replace a Golf Club Shaft at Home
- Choosing the Right Golf Club Shaft. To begin with, you will need to get your hands on a golf club shaft. ...
- Cleaning the Club. Now, take out your utility knife. ...
- Taking the Shaft Out. It is now time to release the head from the shaft. ...
- Scrapping off Any Residuals. ...
- Installing a New Shaft. ...
- Finishing Touches. ...
How do you remove a golf shaft?
Removing a Rear Drive Shaft – This is how you do it
- Mark the Drive Shaft and Remove the Bolts. To know how to remove drive shaft, getting the exact estimation of drive shaft is necessary before beginning the process.
- Eliminate the Drive Shaft Flange. Drive shaft flange can be easily removed by gently shocking with a plastic hammer. ...
- Take out the Drive Shaft. ...
- Reinstall the Drive Shaft and Other Parts. ...
How to remove a golf shaft without a puller?
How to Remove a Golf Shaft From the Head
- Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel. ...
- Place the club in a vise to position it for shaft removal. The club should lie horizontally. ...
- Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. ...
- Clean excess glue out of the hosel to make a comfortable fit for the new shaft. ...
How to repair a broken Golf Club shaft?
Club Repair services
- Re-shaft broken irons from £28.00
- Re-shaft Hybrids from £50.00
- Re-shaft Woods from £60.00
- Drill out broken iron heads and re-shaft £35.00
- Loft & Lie Adjustments per club £3.00
- Swingweight Adjustments per club £5.00
- Extend Graphite shafts saving grips per club £10.00
- Extend steel shafts saving grips per club £8.00
- Shorten Clubs and save grips per club £6.00
How do you pull a broken shaft?
2:249:022020 removing a broken shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you would do is you would heat this area up shove that in there you would turn this until itMoreSo what you would do is you would heat this area up shove that in there you would turn this until it would grab. And when you got a good firm hole handle on it you would turn the nut.
How do you get a broken shaft out of a driver?
1:357:16Removing a Broken Graphite Shaft 2019 -Golf Club Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd this kind of shaft extraction is no different alright so the easiest way that I have found isMoreAnd this kind of shaft extraction is no different alright so the easiest way that I have found is you have to heat up this area and then you step drill.
How do you remove a broken iron head shaft?
0:083:38How to Remove a Steel Shaft Broken Off at the Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can use either number four which it fits in fairly deep. Or a number five screw extractor whichMoreYou can use either number four which it fits in fairly deep. Or a number five screw extractor which will go in about a half an inch.
How do you remove a golf shaft at home?
0:172:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
Can you fix broken golf club shaft?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced. Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself.
How do you remove a broken shaft from a shaft adapter?
0:533:32How to Remove a Graphite Shaft Broken Off at the Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipHead I want to clamp it make sure to clamp it tight but not too tight if I'm gonna crush the top ofMoreHead I want to clamp it make sure to clamp it tight but not too tight if I'm gonna crush the top of the housing. Now you're gonna need a few other things.
How do you remove graphite shaft without a puller?
0:193:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
Why do driver shafts break?
Golf clubs can break due to user error. Broken golf clubs occur when golfers slam the club head into the ground out of frustration. Incorrect storage of the club and poor swing technique will also cause shafts and heads to break.
How do you make a golf shaft puller?
0:296:43Build your own golf club shaft extractor - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4MoreAnd put four bolts in it to hold it to a piece of heavy angle iron just actually is quarter-inch 2x4 bent angle out of stainless steel.
Can I Reshaft my own golf clubs?
The average cost to reshaft your golf clubs is $24 per club plus the cost of the shaft and grip. A new iron shaft and grip can range between $10 and $95 while a new driver shaft and grip can range between $18 and $440. The majority of the cost comes down to what type of shaft you want and what grips you like.
How do you Reshaft a driver at home?
0:144:53How To Reshaft Golf Clubs - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere just as the pocketable bandha looks better with it as you can see two of ours also prep the tipMoreHere just as the pocketable bandha looks better with it as you can see two of ours also prep the tip taken basically the paint off the shaft that way to here to the epoxy.
How do you remove a golf shaft from the head?
1:015:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro willMoreBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro will come right off you can almost pull it off with your hands once it gets softened.
How do you remove graphite shaft without a puller?
0:193:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
Why do driver shafts break?
Golf clubs can break due to user error. Broken golf clubs occur when golfers slam the club head into the ground out of frustration. Incorrect storage of the club and poor swing technique will also cause shafts and heads to break.
How do you change a driver shaft?
0:335:54Golf Equipment : How to Change a Golf Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipTool so we lay it in in this little groove right here. Which is going to slide back and forth andMoreTool so we lay it in in this little groove right here. Which is going to slide back and forth and put pressure and pull on the head. As the shaft is heated. Then we tighten the shaft.
How to remove a broken shaft from a vise?
Step 1. Insert the broken shaft into the vise and remove the shaft by using the heat gun to warm up the hosel and loosen the adhesive that holds the shaft in place. Use medium heat for graphite shafts and higher heat for steel shafts. Once the adhesive has started to melt, pull the broken shaft from the hosel, which is where the shaft meets ...
Can you replace a golf club shaft?
Once a golf club shaft has been broken, it cannot be repaired, but it can easily be replaced. Shafts can be replaced at golf pro shops and most golf stores, but it is also a fairly easy project to do yourself. Replacing your own shaft can save time and money, and allow you to try a new shaft without purchasing new clubs.
How to clean epoxy from hosel?
Clean out any remaining epoxy in the hosel. Begin using a file and scrape away the residue, then apply a solvent to a small rag and wipe down the interior of the hosel. You may want to push the rag in with the tip of a screwdriver or similar tool.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
How to melt glue on a golf club?
Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. Light your propane torch and apply heat to the underside of the hosel. This will melt the glue.
How to remove a ferrule from a hosel?
The ferrule is the small plastic band that sits just above the hosel. With a utility knife or box cutter, cut a vertical slit in the ferrule. Using a flathead screwdriver or pliers, pry the ferrule from the shaft and discard it.
Do you need to reshaft a golf club?
The need to reshaft golf clubs is common. It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly.
How to make a golf club with masking tape?
Step 1. Completely cover the head of the club with masking tape to prevent the head from being scratched during the process. Now, place the club in the vise, so that the middle of the shaft is the part being held in the vise. Make sure the club is held securely.
What degree did Tami Fisher get?
Tami Fisher received her undergraduate degree in mathematics, while also receiving a full-ride golf scholarship. She has extensive experience in the golf industry, as well as the employee benefits area. She is a die-hard Kansas basketball fan, and loves all sports.
Can you replace a golf club shaft instead of replacing the entire club?
By Tami Fisher. Replacing a golf shaft instead of replacing the entire club can save money. Once in a while, something happens to cause a golf club shaft to splinter or even break. When this happens, the old shaft must be removed and a new one installed in its place.
What to do if shaft piece fails to come out?
However, if the shaft piece fails to come out or slip, remove the easyout and repeat the last step. (Note: Never heat the hosel with the easyout inserted into the hosel as this can change the tempering of the easyout and possibly cause it to break off within the hosel) Once the broken piece has been successfully removed from the hosel, ...
How to break epoxy bond?
Once completely cleared out, heat the hosel with a propane torch to break the epoxy bond.
What size drill bit should I use for a tapered hosel?
Because there is the potential that the hosel is tapered, it is suggested that you start out with an undersized drill bit (T-size or smaller). This will help to take a little bit out at a time as well as preserve the tapered hosel.
How long does it take to heat a hosel?
Once completely cleared out, heat the hosel with a propane torch to break the epoxy bond. This may require 30 seconds or more of heat depending upon how old the club is.
Can you remove broken iron shaft?
In the event you still cannot remove the stubborn broken piece of shaft, then it might be advisable to drill the shaft out of the hosel. On many older irons, the hosels are tapered. It is difficult to tell this ahead of time as some heads that may be normally come equipped with a taper tip shaft could have been reshafted ...
How to remove graphite shaft?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
How much does a shaft puller cost?
Shaft pullers can range anywhere from around $20 for a devise that looks like a modified pry bar (you still need a vise and shaft clamp) to several hundred dollars for a hydraulic model. Regardless, invest in a good shaft puller if you are repairing clubs in any sort of volume. Remember how much shafts cost again.
What is a graphite shaft made of?
A graphite shaft is made from many layers of graphite pre-preg or long continuous strands of carbon fiber wrapped around a forming mandrel. To hold the layers or strands together, an epoxy resin is used. This same epoxy resin is not much different from the epoxy that is used to hold the head onto the shaft. In order to remove the head ...
How long to reheat a golf club?
If the clubhead does not come off at this point, reheat for a period of 25-30 seconds. Remember, you can always reheat the hosel, but you can’t remove heat if you heat the club too long. Continue this method of heating for 25 second intervals until the shaft puller has forced the clubhead from the shaft.
How many times can you remove graphite from a clubhead?
Sometimes these steps will have to be repeated as many as 3 or 4 times (or more) before successfully removing the graphite shaft from the clubhead, especially for titanium and aluminum clubheads. The more pressure that the shaft puller applies the less heat it takes to remove the shaft from the clubhead.
Can you discolor a golf club head?
If you do discolor the head, at least it will be on the back side that it least likely to be seen by the golfer when the club is at address. You are now ready to apply heat to the head for the purpose of removing the head from the shaft. It is best to remove the shaft as soon as the epoxy breaks loose.
