How do you remove the axle from a golf cart?
You can also check for a C-clip at the backside of the golf cart that keeps the axle in position. This clip is often inside the axle tube behind the drum mounting flange. Taking this clip off from its place can help you remove the axle from the Club Car. You can remove the rear axle on a Club Car Precedent by carrying out the steps mentioned above.
What causes a drive axle to fail on a golf cart?
The drive axle for a golf cart rarely fails because of the low power of the motors. You may need to remove one to change the bearing or if a gear is stripped.
How to jack up a golf cart?
Chock the front wheels of the Club Car to prevent it from moving. Loosen the lug nuts present at the back of the golf cart. Loosen the nut present on the axle at the end. Raise the rear end of the cart and place it on the jack stand. Take off the rear wheel followed by the brake hub. Check where the axle is positioned at the rear end.
How do you remove the engine on a 2001 EZGO golf cart?
There is an easy way to remove the engine on a 2001 EZGO golf cart. Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How do you remove a shaft axle?
6:2311:05How To Remove a C-Clip Axle Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I'm just going to push on it with my finger. And it drops out that's the c-clip right there andMoreAnd I'm just going to push on it with my finger. And it drops out that's the c-clip right there and that holds the axle shaft. On. There it is again. And you can just rotate it freely and push it out.
How do you remove a golf cart hub?
0:202:18How To Quickly Replace A Stripped Golf Cart Hub - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you're going to want to do is you want to remove the cotter pin this case I used use pryMoreSo what you're going to want to do is you want to remove the cotter pin this case I used use pry some pliers. And a flat tip screwdriver. And you're going to loosen the castle.
How do you change a wheel bearing on a golf cart?
5:0511:47How to replace a golf cart wheel axle bearing. Yamaha G29 - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then your bearing will press off this way and then you press on the new one that way and this isMoreAnd then your bearing will press off this way and then you press on the new one that way and this is what it looks like. And that's it that's with the new bearing.
How much does it cost to replace a rear axle?
The average to repair a front axle is $550 dollars. Rear axle repair costs run a little higher and average about $799 dollars.
How do you remove Club Car DS axles?
How do I remove the rear axle on a Club Car golf cart?Remove the rear wheel of the golf cart.Take off the brake drum from its place.Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring.Slide the axle out of its position.
How can I make my electric EZ Go golf cart go faster?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you grease a golf cart wheel bearing?
0:307:15How To Grease Wheel Bearings - 2 Easy Methods - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just put some grease in the palm of your non-dominant. Hand now take the bearing and you'reMoreAnd just put some grease in the palm of your non-dominant. Hand now take the bearing and you're gonna press it in. So when you get these wheel bearings you need to grease these.
How do you read a club car serial number?
The letters or letter at the beginning of the serial number (1) indicate the vehicle model, could be one or two letters. The following four digits (2) indicate the model year and production week during which the vehicle was built.
Who makes Precedent golf carts?
Club CarClub Car has two main models of golf carts, called theDS and Precedent. The Precedent Club Car model was introduced in 2004, and the DS model has been around since the beginning and is still available in the market today.
How do you change an axle?
4:427:08Fastest and Easiest Way to Replace a CV Axle - YouTubeYouTubeStart of suggested clipEnd of suggested clipOn the transmission. So when you go to put this in you want to make sure you put it straight. AndMoreOn the transmission. So when you go to put this in you want to make sure you put it straight. And you push it all the way in I find that this way is to push it from me once she wants to sing gate.
How much is a drive axle?
On average, you can expect it to cost between $880 and $959 to replace your car axle shaft, depending on the type of car you drive and which axle is broken. However, it's possible that you'll just need to repair your axle rather than replace it.
How do you change a rear axle?
0:483:38How to Replace Rear End on Your Car (Differential) - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust put one on each side so it's even then basically you on bolt everything you take the driveshaftMoreJust put one on each side so it's even then basically you on bolt everything you take the driveshaft off the back. Then you pick up the back seat.
How do you remove lug nuts from a golf cart?
How to remove lug nuts on golf cart. Open the lug nuts with the wrench and hammer while the wheel stays on the ground. After loosening the nuts, use your hand to open the nuts and replace them or tighten them for the performance.
How do you remove golf trolley wheels?
0:501:47How To Take Off Remove A Golf Cart Wheel - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can just slide it right. Off. All right so once you have the wheel jacked up i i don't do itMoreYou can just slide it right. Off. All right so once you have the wheel jacked up i i don't do it much more than two inches at most it's just not necessary. Um you just loosen up the bolts.
How do you remove a wheel from a cart?
0:071:23How To Replace Toter® Cart Wheels - YouTubeYouTubeStart of suggested clipEnd of suggested clipPlace the head of the screwdriver on the tab. And with your hammer hit the screwdriver at leastMorePlace the head of the screwdriver on the tab. And with your hammer hit the screwdriver at least twice rotate the pelvis. And repeat pull off the pal nut.
Why wont my golf cart go forward or reverse?
Check the Forward/Reverse switch of your golf cart for loose connections. If the connections are intact, interchange the top and bottom wires at the rear. If the cart now goes in reverse but not forward, the problem is with the switch. You have to just change the switch in this case.
Why does my golf cart drive axle fail?
The drive axle for a golf cart rarely fails because of the low power of the motors. You may need to remove one to change the bearing or if a gear is stripped.
How to tighten a golf car bearing?
Screw the bearing puller into the center of the axle and wrap its arms around the back bearing housing. Tighten the bearing puller until the bearing is released. Pull the axle from the golf car with your hands. Some bolts may be locked in place because of their age.
When was the golf cart invented?
The golf cart was invented in 1962 by Merlin L. Halvorson. The golf cart allows golfers a more relaxing way of getting around the course verses walking and carrying their clubs. Like all mechanical devices, golf carts require maintenance and repair to operate properly.
How to remove the rear wheel of a golf cart?
Remove the rear wheel of the golf cart. Take off the brake drum from its place. Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring. Slide the axle out of its position. You may require a slide hammer to help you with releasing the bearing from the axle if it’s stuck on to it.
Where is the C clip on a golf cart?
You can also check for a C-clip at the backside of the golf cart that keeps the axle in position. This clip is often inside the axle tube behind the drum mounting flange.
How to remove the shaft on a club car DS?
How to remove the axle shaft on Club Car DS. You will need a few chocks, a pair of 90-degree internal snap ring pliers, a floor jack and jack stands to remove the axle shaft on a Club Car DS. The steps given below can help you to take off the axle shaft from the golf cart. Keep the chocks before the front wheels of the Club Car.
How to remove rear axle snap ring?
You can remove the rear axle snap ring on a Club Car using a pair of 90-degree snap ring pliers and a flashlight. Take off the rear wheel from the Club Car golf cart. Remove the brake drum from its place.
How to tell if rear axle bearing is bad?
The most common giveaway sign of a bad rear axle bearing is a loud noise coming from the axle assembly. You can try one of the following tips to solve the problem.
What to use to knock off a burr on a ring?
If the groove that houses the ring is damaged with a burr on the edges, you can use the edge of a small three-sided file to knock off the burr. This is often helpful when the axle is installed.
How to remove rear axle seal on 2002 Club Car DS?
In a 2002 Club Car DS, you can remove the rear axle seal from the axle opening by popping it out using a seal puller. If you want to install a new axle assembly, you’ll have to do the above steps followed by fitting the new assembly in place and redoing these steps once again in the reverse order.
Why is it so hard to remove a golf cart motor?
On most occasions, the difficulty in removing the motor from its place in a golf cart is due to the rust that would have developed all around. It won’t come off so easily and you can’t use too much force as it may damage some of the other parts.
How to change motor on Ezgo cart?
How to change the motor on a Electric EZGO: The first step is to remove the wires connecting the battery pack to ensure that the cart has no power. It is advisable to use protective gloves. Do not use wristwatch, rings or jewelry.
How to yank a cart motor out?
Another simpler way to yank the motor out would be to remove the left side rear wheel of the cart out. You can then place the jack (if it is a hydraulic one) beneath the motor. This way, once you have removed all the cables connected to the motor and the bolts, it becomes very easy to remove the motor.
How to remove the engine on a 2001 Ezgo?
Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How to remove PDS motor?
Here are the steps to remove a PDS motor: You must first put the Run-Tow/Maintenance switch to Tow/Maintenance. Disconnect the wires connecting the battery. Disconnect and remove all the wires and cables connected to the motor. You should then remove the snap ring and the speed sensor from the motor end cover.
Can you pull an EZGO cart up?
For starters, the input shaft could be jammed or broken, making it difficult for you to pull the motor up. You can use a hammer mildly to slowly tap and pull it off the hold and pull it up. The other issue you may face with the older models of EZGO carts is where the motor could be welded to the body.
