Jack up the rear of the golf cart with the car jack and place two jack stands under the rear end, supporting it with the tires off the ground. Step 2 Unscrew the bolts that secure the rim on the hub. Pull off the tire and rim.
How to take off axle shaft from golf cart?
The steps given below can help you to take off the axle shaft from the golf cart. Keep the chocks before the front wheels of the Club Car. Raise the back part of the cart using a floor jack. Support the cart by keeping jack stands below the axle tubes. Take off the back wheel and rim followed by the brake drum.
How do you remove the rear axle from an EZGO golf cart?
How do you remove the rear axle on a EZGO golf cart? The steps to remove the rear axle on a EZGO golf cart are:-Remove the tires by giving support to the back of the cart with help of chocks. Pull out the brackets fastening from the frame of the engine, and also take out the muffler.
What causes a drive axle to fail on a golf cart?
The drive axle for a golf cart rarely fails because of the low power of the motors. You may need to remove one to change the bearing or if a gear is stripped.
How to remove axle shaft on a club car DS?
You will need a few chocks, a pair of 90-degree internal snap ring pliers, a floor jack and jack stands to remove the axle shaft on a Club Car DS. The steps given below can help you to take off the axle shaft from the golf cart.
How do you remove a shaft axle?
6:2311:05How To Remove a C-Clip Axle Shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I'm just going to push on it with my finger. And it drops out that's the c-clip right there andMoreAnd I'm just going to push on it with my finger. And it drops out that's the c-clip right there and that holds the axle shaft. On. There it is again. And you can just rotate it freely and push it out.
How do I take apart my EZ Go golf cart?
6:569:35EZGO TXT Body Removal | How to Remove Golf Cart Body | Episode 1YouTubeStart of suggested clipEnd of suggested clipAcross the backyard you've got four little round tabs these tabs have to be pried out and then underMoreAcross the backyard you've got four little round tabs these tabs have to be pried out and then under each one is a 7/16 bolts we'll take those out and get started we're just about done now.
How do you remove the rear axle on a Club Car golf cart?
How do I remove the rear axle on a Club Car golf cart?Remove the rear wheel of the golf cart.Take off the brake drum from its place.Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring.Slide the axle out of its position.
How do you change a wheel bearing on a golf cart?
5:0511:47How to replace a golf cart wheel axle bearing. Yamaha G29 - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then your bearing will press off this way and then you press on the new one that way and this isMoreAnd then your bearing will press off this way and then you press on the new one that way and this is what it looks like. And that's it that's with the new bearing.
What is the difference between ezgo medalist and TXT?
Some of the differences between the EZGO RXV and TXT golf cart models are as below: The EZGO RXV models are more customizable than the TXT models....EZGO Freedom TXTEZGO Freedom RXVLength93 inches94.5 inchesHeight67.5 inches70 inchesWheelbase66 inches65.7 inchesFront wheel track34 inches35.5 inches9 more rows
How do you remove an armature from a golf cart motor?
0:301:56How To Remove The Motor Armature - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you want to do is get a hammer just like this and a flathead screwdriver. You want to justMoreSo what you want to do is get a hammer just like this and a flathead screwdriver. You want to just tap on the end no the front end. Oh. Coming out you guys what a wiggle. The armature gently.
What is a differential on a golf cart?
Maintaining your golf cart's differential and transmission is essential to your vehicle's performance and longevity. Your differential transmits torque to the Club Car wheels and allows them to turn at different speeds.
How do you remove a golf cart hub?
0:162:18How To Quickly Replace A Stripped Golf Cart Hub - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what you're going to want to do is you want to remove the cotter pin this case I used use pryMoreSo what you're going to want to do is you want to remove the cotter pin this case I used use pry some pliers. And a flat tip screwdriver. And you're going to loosen the castle. Nut.
How do you grease a golf cart wheel bearing?
0:307:15How To Grease Wheel Bearings - 2 Easy Methods - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd just put some grease in the palm of your non-dominant. Hand now take the bearing and you'reMoreAnd just put some grease in the palm of your non-dominant. Hand now take the bearing and you're gonna press it in. So when you get these wheel bearings you need to grease these.
How do you read a club car serial number?
The letters or letter at the beginning of the serial number (1) indicate the vehicle model, could be one or two letters. The following four digits (2) indicate the model year and production week during which the vehicle was built.
Why does my golf cart drive axle fail?
The drive axle for a golf cart rarely fails because of the low power of the motors. You may need to remove one to change the bearing or if a gear is stripped.
How to tighten a golf car bearing?
Screw the bearing puller into the center of the axle and wrap its arms around the back bearing housing. Tighten the bearing puller until the bearing is released. Pull the axle from the golf car with your hands. Some bolts may be locked in place because of their age.
When was the golf cart invented?
The golf cart was invented in 1962 by Merlin L. Halvorson. The golf cart allows golfers a more relaxing way of getting around the course verses walking and carrying their clubs. Like all mechanical devices, golf carts require maintenance and repair to operate properly.
How to fix loose lug nuts on golf cart?
A lug wrench can be an effective tool to fix loose lug nuts on a golf cart. Open the lug nuts while the wheel is on a even surface and making full connection with the ground. After opening the nuts change them with the new nuts. Check the frame of the wheel – if it is out of shape then change the frame.
How far apart is a 4x4 golf cart?
The cart has the bolt pattern 0f 4X4 that is 4 inches by 4 inches which is 100mm apart. The 4×4 is the basic and standard size for every golf carting vehicle. Do not over tighten nut to prevent it from the breakdown and regular oiling in the parts is recommended to save it from rust.
How many holes are in an EZGO TXT bolt pattern?
EZGO TXT bolt pattern is 4×4 (4 inches by 4 inches, or 100mm apart). When measured diagonally, the wheel has 4 holes spaced out. This is the standard bolt pattern which comes with all the carting vehicles.
What size nuts are used in a golf cart?
3/4″ sized nuts are used in the axle of a EZGO golf cart. Don’t over tighten the nut as it will result in slipping of the axle and can cause damage to the complete axle set. Oiling is very important to prevent the axle from rusting and slipping.
Why does my EZGO golf cart keep spinning?
The reason the castle nut keeps spinning on a EZGO golf cart is because the nut is too tightened on the slip axle. This means the grip on the axle has worn and the axle needs replacing. Spinning can occur due to too much pressure applied and overtightening of the nut.
What size castle nut is used on a EZGO golf cart?
The standard size of the castle nut on a EZGO TXT golf cart is 1.2 inches X 1.05 inches X 0.65inches. It is usually made up of alloy steel designed specifically for EZGO brand.
How to remove lug nuts?
Steps to remove lug nuts. Park the vehicle in the level surface the wheel stays completely on the group evenly. Remove the cap placed on hub and try locating the lug nut in your vehicle. The hubcap needs to be removed for accessing the lug nut. Check the lug nut before the removal process.
How to secure an axle?
Use a length of rope or wire to support the axle while you remove the inner end. Some vehicles use bolts or clips to secure the inner axle, while others can be just pulled free with a slide hammer. Place a drain pan under transmission/differential to catch any fluid that might leak out.
What is drive axle?
What Is a Drive Axle? On early cars, the drive axle was just a solid rod with two wheels on it turned by a chain, just like on a go-kart, and in your car or truck it still performs the same function; delivering power from the transmission to the wheels. Trucks, and cars with a solid rear axle, still have a simple rod hidden inside ...
How to remove the rear wheel of a golf cart?
Remove the rear wheel of the golf cart. Take off the brake drum from its place. Insert a 90-degree snap ring pliers through the holes in the hub and remove the snap ring. Slide the axle out of its position. You may require a slide hammer to help you with releasing the bearing from the axle if it’s stuck on to it.
How to remove the shaft on a club car DS?
How to remove the axle shaft on Club Car DS. You will need a few chocks, a pair of 90-degree internal snap ring pliers, a floor jack and jack stands to remove the axle shaft on a Club Car DS. The steps given below can help you to take off the axle shaft from the golf cart. Keep the chocks before the front wheels of the Club Car.
How to remove rear axle snap ring?
You can remove the rear axle snap ring on a Club Car using a pair of 90-degree snap ring pliers and a flashlight. Take off the rear wheel from the Club Car golf cart. Remove the brake drum from its place.
How to tell if rear axle bearing is bad?
The most common giveaway sign of a bad rear axle bearing is a loud noise coming from the axle assembly. You can try one of the following tips to solve the problem.
How to remove rear axle seal on 2002 Club Car DS?
In a 2002 Club Car DS, you can remove the rear axle seal from the axle opening by popping it out using a seal puller. If you want to install a new axle assembly, you’ll have to do the above steps followed by fitting the new assembly in place and redoing these steps once again in the reverse order.
Where is the C clip on a golf cart?
You can also check for a C-clip at the backside of the golf cart that keeps the axle in position. This clip is often inside the axle tube behind the drum mounting flange.
Where is the retainer nut on a 1998 Club Car?
The axle bearing of a 1998 electric Club Car rear axle houses a retainer nut that is located inside the axle tube. This is often a C-clip and keeps the axle in position inside the tube. This C-clip or retainer nut can be accessed only using a pair of 90-degree C-clip pliers.