Place the club in a vise to position it for shaft removal. The club should lie horizontally. Make sure the vise grips the shaft securely to prevent it from slipping out. Expose the length of the head and about 8 inches of shaft.
Full Answer
How do you remove a golf shaft from the head?
Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly. Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel.
How to remove a broken shaft from a club?
Golfworks sells a SHAFT EXTRACTOR BAR for $14.99 + s & h. Apply heat all around the hosel and the face of the club. Clamp the shaft in a vise using a VISE CLAMP $1.99 at Golfworks, apply heat then using the bar, push the head off. If you go slowly and apply heat continously while pushing the head it will come off. Don't rush!!
How to remove adapter from graphite shaft?
How to remove adapter from graphite shaft? Negative on the heat gun. It puts MORE heat into the adapter and shaft than a torch. Use a torch and heat for 5 seconds and then pull off adapter. I would pull it like just like Nessism described.
Do you need a professional to reshaft a golf shaft?
It is sometimes necessary to have a professional tackle a complete reshaft job; however, it can make his job easier if you eliminate a step in the process. Removing a golf shaft from the head is fairly simple; however, it must be done carefully and properly. Remove the ferrule.
How do you remove an adjustable tip from a golf shaft?
0:119:32How to Remove Golf Shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right underMoreOnce you start to see it's a bubble up a little bit just take your hook blade. Slide it right under there. And it should come off free easy a little cold out here in the shop tonight.
How do you remove driver shaft tips?
8:0917:13How To remove / Install a Golf shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipSometimes there's not just like we've talking. Taking talking talked about here you and then whichMoreSometimes there's not just like we've talking. Taking talking talked about here you and then which case you would just put where it sits up against the the puller will set up against this just like it
How do you remove the head of a golf club shaft?
1:015:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro willMoreBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro will come right off you can almost pull it off with your hands once it gets softened.
How do you remove shafts from an iron?
6:4814:27pulling a golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd I like to do is I like to pinch. Down. And then pull back pinch down and then pull back. AndMoreAnd I like to do is I like to pinch. Down. And then pull back pinch down and then pull back. And this way you don't scrape a shaft.
Can you take the tip off a shaft?
Shaft tipping is when a club builder removes length from the tip section of a shaft, which is the end where the clubhead is installed. In most cases, tip trimming a shaft makes it meaningfully stiffer.
How do you remove graphite shaft without a puller?
0:193:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
How are golf club heads attached to the shaft?
Golf Club Epoxy. Adhesives are used in many different sports equipment bonding applications. One such application is that of bonding heads onto shafts for golf clubs. It sounds like an easy application and in principle it is – put some adhesive on the tip of the shaft and then insert it into the club head.
How do you remove a steel shaft from a hosel?
0:383:38How to Remove a Steel Shaft Broken Off at the Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can use either number four which it fits in fairly deep. Or a number five screw extractor whichMoreYou can use either number four which it fits in fairly deep. Or a number five screw extractor which will go in about a half an inch.
How do you replace club heads?
1:4010:45How to replace a golf club shaft - Step by Step - YouTubeYouTubeStart of suggested clipEnd of suggested clipProbably start off on high but you want to move it around on actual the hostile here kind of andMoreProbably start off on high but you want to move it around on actual the hostile here kind of and spinning it around a little bit and make sure you get this superhot.
How do you prepare a shaft tip?
Shafts: Lightly sand shaft from tape to tip with 150 grit or finer sand paper to remove the polyurethane finish and all the paint. This operation is "prepping" the shaft and can be done by The GolfWorks (PREP).
How do you change the shaft on an iron?
HOW TO RESHAFT GOLF CLUBSSteel Shafts: To remove a steel shaft from a metal wood or iron, place the shaft in a super lock tight shaft holder. ... Measure the shaft tip. ... After the tip has been trimmed, abrade or roughen the shaft tip. ... Align the shaft graphics the way you want them by rotating the shaft.More items...
How do you pull a steel golf shaft?
0:042:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also use a heat gun but it's going to take three times as long. The other things that you'reMoreYou can also use a heat gun but it's going to take three times as long. The other things that you're going to need or a club making vice vice clamp some heavy-duty gloves and probably a knife.
How to clean epoxy from hosel?
Clean out any remaining epoxy in the hosel. Begin using a file and scrape away the residue, then apply a solvent to a small rag and wipe down the interior of the hosel. You may want to push the rag in with the tip of a screwdriver or similar tool.
Do you need a new shaft for golf?
Almost every golfer will need a new shaft at some point during his golfing career. Clubs can be reshafted at most golf stores and country clubs, but if you are a do-it-yourself type, removing and/or installing a new shaft is a straightforward project that will save you money.
SouthPaw87
I currently have a Tour AD-6X shaft with a Callaway Razr Fit tip on it. I am not a clubmaker, so I thought I'd ask the experts...
Lord Helmet
Im not a clubmaker and Im certainly not an expert, but I can say with relative certainty that yes I qualified clubmaker can swap tips. Some tips will go up further on the shaft so you might have some tip prep area exposed. Ping adapters seem to be shorter in length compared to others (Ive heard that) so that is why I mention this.
Nessism
A small torch is the proper tool. Only use a heat gun if you have an accessory tip that funnels the air down into a small outlet port. Your typical wide mouth air gun outlet port spews heat out over a much wider area than desired, so MORE heat will go into the shaft than ideal.
Step 2: Open a Tube of CA Glue
My tube of superglue almost always glues its cap on itself, making it almost impossible to remove. Luckily, because CA is so fragile, when you squeeze the cap in a vise, it crumbles.
Step 3: Pry Open Electronic Devices
A vise is a great tool for prying open electronic devices, from phone chargers and computer mice, to flash-drives and TV remotes.
Step 4: Hold PCB's While Soldering
Before I built WAVE, I would hold big circuit boards in my vise. This would come in handy while trying to unsolder big components such as electrolytic capacitors and relays, but it wasn't really comfortable for soldering components on PCB's.
Step 5: How to Save Space- Clamp Tools in Your Vise!
One of my favorite uses for a vise is for clamping tools. Whether if you're using it to save space by making a mini portable router table, or using it to hold your sharpening stone, it's always extremely useful!
Step 6: How to Make an Improvised Drill-Press With a Vise
Since I have only two hands, it was pretty much impossible to take pictures for this step.
Step 7: How to Make an Improvised Vise With a C-Clamp
I made this way before my grandpa gave me my vise. This was taken apart the day I restored my metal vise, meaning that these pictures was taken a long time ago, so sorry for the quality...
