Using your wrench, remove the bolt on the gas pedal shaft. Slide the shaft up so there is more play in the gas pedal. Tighten the bolt and then start the cart. You may need to adjust the gas pedal shaft a couple of times before you have it to your liking. Removing the Governor From E-Z-Go Carts
Full Answer
How do you bypass the governor on an EZGO golf cart?
You can bypass the governor connection in an EZGO or Yamaha G1 golf cart as given below. Remove the cable connecting the carburetor and the governor. Disconnect the connection between the gas pedal and the governor. Connect the gas pedal directly to the carburetor opening.
How long does it take to adjust the governor on an EZGO?
With governor adjustment, the EZGO cart can go faster by 5 to 10mph. In other words, the 15mph speed can be raised to 22mph with the adjustment. It usually takes only five minutes to get the adjustment done. It doesn’t take much time or skill to remove a golf cart governor.
Can you adjust the governor on an EZ GO spark plug?
Many manufacturers, including EZ Go, do not want consumers tampering with their engines, and have thus hidden the governors in the spark plug ignition. This is very difficult to adjust without ruining the engine, and should be left to trained professionals. How can I stop the choke cable from getting hot on my EZ-GO golf cart?
How do you adjust the throttle on an EZGO golf cart?
In some cases, the adjustment can be done by turning the cable nut that connects the cable to the throttle lever in the counter-clockwise direction. This type of governor is often found in 2-cycle golf carts. The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph.
How do you remove the governor on a ezgo golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
How do you turn off the governor on a electric golf cart?
0:061:28Golf Tips & Etiquette : Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment.MoreWell a golf cart's governor located is actually down in the motor. Compartment.
How do you adjust the speed limiter on a EZ Go golf cart?
0:495:06How to Adjust an E Z Go Golf Cart Governor - WikiVideo - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut.MoreIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut. The more you tighten the larger nut the faster your cart will.
Is there a governor on an electric ezgo golf cart?
Considering electric golf carts don't have governors like gas powered carts, the old-school method of simply removing the governor is not an option.
How can I make my electric EZ Go golf cart go faster?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How can I make my electric golf cart go faster without upgrading?
How to Make an Electric Golf Cart Faster Without UpgradesWash Your Cart Properly. ... Inspect the Batteries. ... Refill the Battery Water. ... Check the Gas Pedal and Linkage. ... Measure the Tire Pressure. ... Charge Up Your Battery Unit. ... Lighten Up Your Cart's Weight.
How do you adjust the governor on a golf cart?
Adjusting an EZ-GO Golf Cart GovernorStep 1 - First, lift the seat of your engine to reveal seat cousins. ... Step 2 - Remove the seat cushions over your motor. ... Step 3 - Remove the black plastic cover to expose the motor. ... Step 4 - Loosen the smaller one and tighten the larger one to increase your cart's speed.More items...•
Where is the speed controller on an ezgo golf cart?
These speed controllers are located under the EZGO cart seat. Check the speed controller's attachment near the carburetor.
Where is the governor on a golf cart?
0:101:28Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment. Some of them theseMoreWell a golf cart's governor located is actually down in the motor. Compartment. Some of them these electric ones nowadays. Actually the governor isn't a true governor. It is a control speed.
How do you bypass the governor on a golf cart?
0:000:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the farther you bend that normally the faster it goes and then that's it basically when you wantMoreSo the farther you bend that normally the faster it goes and then that's it basically when you want to return your heart you just bend that back down and go back to normal speed.
What does removing the governor do?
Removing the governor will increase the maximum rpm of the engine, but the internal parts of the Predator 212 are designed for 3600 rpm. Generally, this isn't an issue with just the governor removal, the internal parts can usually withstand 5000 rpm without breaking apart (unless you go full throttle for too long).
Why is my electric golf cart so slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
What is a golf cart governor?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
Can you remove a golf cart governor?
It doesn’t take much time or skill to remove a golf cart governor. With some basic mechanical expertise and general-purpose tools, you can do this yourself. The process is more or less the same in all golf carts.
How to remove governor from golf cart?
How to Remove the Governor From a Golf Cart. You hit the links. The course is open in front of you as far as the eye can see. The only thing holding you back is the put-put-puttering of your golf cart. Golf carts are governed to go anywhere from 12 to 14 miles per hour. But if you've got a few minutes, some simple mechanical know-how and a wrench, ...
Where is the governor on a car?
The governor generally sits on top of the engine . This is the easiest way to find the carburetor. Once you've followed the cable up to the governor, disconnect it there as well. You can save this cable for later use or throw it away.
How fast can a golf cart go?
Golf carts are governed to go anywhere from 12 to 14 miles per hour. But if you've got a few minutes, some simple mechanical know-how and a wrench, you can double the speed of your cart and zip through your round.
How to adjust a gas pedal on a cart?
Using your wrench, remove the bolt on the gas pedal shaft. Slide the shaft up so there is more play in the gas pedal. Tighten the bolt and then start the cart. You may need to adjust the gas pedal shaft a couple of times before you have it to your liking.
How fast can a factory cart go?
The factory gear most likely has a 12.5:1 ratio, which allows the cart to achieve somewhere around 14 mph. If you swap out the factory gear for one with an 8:1 gear ratio, you'll up your top end to about 20 mph.
How to make a cart faster?
Step 1. The first option to making your cart faster is to replace the electronic speed control. This will enable more voltage to pass to the motor, producing the desired result. Unfortunately, this upgrade is not inexpensive as the unit can run anywhere from $100 to $1,000. Step 2.
Can you drive a golf cart faster?
It should be noted that the golf cart you are trying to make faster may not be designed to do so. Weigh the options carefully and exercise caution whenever driving a golf cart at any speed. Remember that golf carts are not equipped with seat belts, air bags and other safety equipment that you find in automobiles.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How many screws are in a golf cart engine?
There should be five screws in most models. The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. ...
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
How to change motor on Ezgo cart?
How to change the motor on a Electric EZGO: The first step is to remove the wires connecting the battery pack to ensure that the cart has no power. It is advisable to use protective gloves. Do not use wristwatch, rings or jewelry.
How to remove the engine on a 2001 Ezgo?
Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How to yank a cart motor out?
Another simpler way to yank the motor out would be to remove the left side rear wheel of the cart out. You can then place the jack (if it is a hydraulic one) beneath the motor. This way, once you have removed all the cables connected to the motor and the bolts, it becomes very easy to remove the motor.
How to remove PDS motor?
Here are the steps to remove a PDS motor: You must first put the Run-Tow/Maintenance switch to Tow/Maintenance. Disconnect the wires connecting the battery. Disconnect and remove all the wires and cables connected to the motor. You should then remove the snap ring and the speed sensor from the motor end cover.
Why is it so hard to remove a golf cart motor?
On most occasions, the difficulty in removing the motor from its place in a golf cart is due to the rust that would have developed all around. It won’t come off so easily and you can’t use too much force as it may damage some of the other parts.
Can you pull an EZGO cart up?
For starters, the input shaft could be jammed or broken, making it difficult for you to pull the motor up. You can use a hammer mildly to slowly tap and pull it off the hold and pull it up. The other issue you may face with the older models of EZGO carts is where the motor could be welded to the body.
Do E-Z-Go Golf Carts have titles?
E-Z-Go Golf Carts, unlike vehicles, do not have a title, but they do have serial numbers. If you are buying a golf cart, it is essential to check the serial number to ensure you do not buy a stolen one. Each E-Z-Go Golf cart has a unique serial number that you can use to identify your golf cart.
Where is the E-Z-Go Cart Serial Number
As mentioned above, all E-Z-Go Golf carts have unique serial numbers. These numbers are essential when buying replacement parts for your golf cart. Textron Specialized Vehicles has been building golf carts for a long time, and the serial numbers are placed on different parts of the golf carts.
How do I push my E-Z-Go Golf Cart?
It can be frustrating when your battery is flat and your golf cart will not roll. To push it to the nearest charging or gas station, you need to release the motor brake. Follow these easy steps to do that.
Why does my E-Z-Go golf cart not move
There are several reasons why your cart refuses to move, but you should check the battery before anything else. If the battery is charged, here are some other reasons why your golf cart will not move.
Are all E-Z-Go Golf carts electric?
No, there are both electric and gas-powered E-Z-Go Golf carts available. Bear in mind that there are several models you can drive on the street, but those are all-electric. These electric models run on batteries that you have to charge at least every 24 hours, depending on how much you use them.
How to tell the Assembly year of my E-Z-Go golf cart
The placement of serial numbers is discussed above, and you will find the manufacturer’s number right next to it. The manufacturer’s number consists of one letter and 3 or 4 numbers. The last two numbers indicate the last two digits of the year of assembly.
How to service E-Z-Go Golf Cart
Like all vehicles, E-Z-Go golf carts require regular maintenance to enhance longevity and performance. You should ensure that your golf cart is serviced after every six months of use. That will ensure that you spot problems and repair them early, which will help reduce repair costs. Here are essential guidelines for E-Z-Go golf cart maintenance.
