Using your wrench, remove the bolt on the gas pedal shaft. Slide the shaft up so there is more play in the gas pedal. Tighten the bolt and then start the cart. You may need to adjust the gas pedal shaft a couple of times before you have it to your liking. Removing the Governor From E-Z-Go Carts
Full Answer
How do you bypass the governor on an EZGO golf cart?
You can bypass the governor connection in an EZGO or Yamaha G1 golf cart as given below. Remove the cable connecting the carburetor and the governor. Disconnect the connection between the gas pedal and the governor. Connect the gas pedal directly to the carburetor opening.
How long does it take to adjust the governor on an EZGO?
With governor adjustment, the EZGO cart can go faster by 5 to 10mph. In other words, the 15mph speed can be raised to 22mph with the adjustment. It usually takes only five minutes to get the adjustment done. It doesn’t take much time or skill to remove a golf cart governor.
Can you adjust the governor on an EZ GO spark plug?
Many manufacturers, including EZ Go, do not want consumers tampering with their engines, and have thus hidden the governors in the spark plug ignition. This is very difficult to adjust without ruining the engine, and should be left to trained professionals. How can I stop the choke cable from getting hot on my EZ-GO golf cart?
Can you remove a governor from a golf cart?
Having taken off your golf cart’s existing governor, you can now place a new one back into its original position and reattach it with screws. If you’re not looking for more speed and just want to maintain the same speed as before, you can leave the governor off.
How do you remove the governor on a ezgo golf cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
Can you remove a golf cart governor?
Here's another fun fact, though: you can remove or deactivate the governor from your cart engine to speed up your cart. You need to be very careful when you perform this step, though, because you may end up making a mistake that damages your engine.
How do you take the governor off a cart?
0:000:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the farther you bend that normally the faster it goes and then that's it basically when you wantMoreSo the farther you bend that normally the faster it goes and then that's it basically when you want to return your heart you just bend that back down and go back to normal speed. And yeah that's it.
How do you adjust the speed limiter on a EZ Go golf cart?
0:495:06How to Adjust an E Z Go Golf Cart Governor - WikiVideo - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut.MoreIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut. The more you tighten the larger nut the faster your cart will.
What does removing the governor do?
Removing the governor will increase the maximum rpm of the engine, but the internal parts of the Predator 212 are designed for 3600 rpm. Generally, this isn't an issue with just the governor removal, the internal parts can usually withstand 5000 rpm without breaking apart (unless you go full throttle for too long).
Where is the governor on a ezgo golf cart?
The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. Follow the thickest cable coming from the gas pedal until your find a small spring wrapped around a metal rod. This is the governor.
How do I turn off speed governor?
1:072:00How to remove your car's speed limiter como sacar limitacion de ...YouTubeStart of suggested clipEnd of suggested clipSelect on that and then. When you press cancel it means you're done and the tune will start toMoreSelect on that and then. When you press cancel it means you're done and the tune will start to upload you'll hear the fan kick on and then when you're all done it'll say the press select to enter.
How do you change the governor on a golf cart?
If you find this rod, then your governor can be easily adjusted by accessing the cart's inner workings. Simply adjust the cable coming from this metal protrusion, turning the nut counterclockwise to make the cable longer, effectively adjusting the cart's governance to increase the overall speed.
How fast can a golf cart go without a governor?
What is the Average Golf Cart Speed? The average top speed of a typical golf cart without any upgrades is between 12 and 14 miles per hour. Without any sort of modification or upgrade on a golf cart, the top speed that you will be getting on a golf cart is about 14mph.
How can I increase the speed of my golf cart?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
Where is the speed controller on an ezgo golf cart?
These speed controllers are located under the EZGO cart seat. Check the speed controller's attachment near the carburetor.
How do I speed up my EZ GO TXT electric golf cart?
You can make your EZGO golf cart go much faster by adding more torque, upgrading the motor of or increasing the voltage of the batteries.Add more torque.Upgrade the motor.Increase the battery voltage.Decrease the load.
How fast can a golf cart go without a governor?
What is the Average Golf Cart Speed? The average top speed of a typical golf cart without any upgrades is between 12 and 14 miles per hour. Without any sort of modification or upgrade on a golf cart, the top speed that you will be getting on a golf cart is about 14mph.
How can I make my electric golf cart go faster without upgrading?
How to Make an Electric Golf Cart Faster Without UpgradesWash Your Cart Properly. ... Inspect the Batteries. ... Refill the Battery Water. ... Check the Gas Pedal and Linkage. ... Measure the Tire Pressure. ... Charge Up Your Battery Unit. ... Lighten Up Your Cart's Weight.
How do you make a golf cart go faster?
6 Ways You Can Make a Golf Cart FasterAdd More Torque to Your Golf Cart.Upgrade Your Golf Cart's Motor.Improve the High-Speed Controller of the Cart.Add Better Golf Cart Tires.Use a Higher Powered Golf Cart Battery.Watch the Weight in Your Golf Cart.
How do you bypass a speed sensor on a golf cart?
The speed sensor on the EZGO golf cart can be bypassed by unplugging it from the speed controller. By disconnecting the J5 pin on the speed controller, this will cause the golf cart to creep along as the controller will go into limp mode.
What is a golf cart governor?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
Can you remove a golf cart governor?
It doesn’t take much time or skill to remove a golf cart governor. With some basic mechanical expertise and general-purpose tools, you can do this yourself. The process is more or less the same in all golf carts.
How fast is an EZGO golf cart?
A typical EZGO golf cart has a top speed of about 15 miles per hour or so and removing the governor is known to add another seven or eight miles per hour to its operating speed.
Why do golf carts have governors?
Golf cart manufacturers put a governor on their vehicles for a reason – they enhance the safety of a cart and keep it from becoming potentially dangerous to a driver. By removing the governor, you are increasing the speed of a cart that may not have extensive crash protection design or even seatbelts.
What do you need to tighten a golf cart?
First of all, you’ll need a handful of wrenches that can be easily adjusted. These wrenches will be used to do things like tighten the governor screw on a golf cart and make it easier to tweak. You may also need some wrenches to open up your engine or other panels on your cart.
How fast can a golf cart go?
That may seem disappointing but is just part of how the cart operates. You may, therefore, only be capable of speeds of up to 10-15 miles per hour.
Can you remove the governor from a golf cart?
People who try to remove the governor from their golf cart often have inflated ideas of what this process will do for their performance. Some may think that they can suddenly jump up to speeds that make their cart a low-speed vehicle. However, that is very rarely the case.
Can you remove the governor from a cart engine?
However, there is also a part known as a governor that keeps your cart’s speed at a safer and more reasonable level. Here’s another fun fact, though: you can remove or deactivate the governor from your cart engine to speed up your cart. You need to be very careful when you perform this step, though, because you may end up making a mistake ...
How Does a Golf Cart Governor Work
Governors play an important role in electric golf carts by limiting the speed they can travel. This is an important safety feature, as it prevents the cart from going too fast and helps ensure passengers’ safety.
How to Take the Governor off a Golf Cart
Removing the governor from a golf cart is a simple process that can be done with common tools. Here’s what you’ll need:
Frequently Asked Questions about Golf Cart Speed Governors
If you’re looking for ways to speed up your golf cart, there are a few things you can do. Start by removing the governor on top of the engine if you haven’t already. If it doesn’t have a governor, then you’ll need to open up the cart and look at the gear shaft to see if it’s turning.
How to adjust EZ Go cart governor?
To adjust an EZ Go Cart Governor engine, start by removing the seat so that you can access the engine. Once the seat is off, remove the screws from the black plastic cover at the rear of the seat and then set the cover aside.
How to make a golf cart go faster?
Loosen the small nut and tighten the larger nut. The more you tighten the larger nut, the faster your cart will go. Start slowly, only tightening the nut a quarter turn to start. You can over-stress the engine if you try to run it too quickly, and it will skip and potentially burn out if you are too eager.
How to get a cart to move faster?
1. Remove the seat and plastic covering over the engine. Sometimes you'll need to remove screws while some models have seats that pop right out. Expose the engine so that you can get to work adjusting the motor. If you don't have a central governor spring, you can still get your cart to move a little faster.
How fast can a golf cart go?
Adjusting the governor can make your golf cart go 5–10 mph (8 .0–16.1 km/h) faster. If you do this to an E-Z-GO golf cart, you might be able to go from 15 mph (24 km/h) to 22 mph (35 km/h). It will only take about 5 minutes to do it. Steps.
How many screws are in a golf cart engine?
There should be five screws in most models. The engine is in the front of golf carts, underneath this panel. Take off the plastic cover and set it aside with the seats. ...
How to change the speed of a car?
Locate your clutch pedal and line. The clutch is the pedal (sometimes a handle near your knee) that you use to put the car into reverse or change speeds. You can adjust the clutch to send more gas to your engine, moving you faster. ...
How to raise the top speed of a golf cart?
To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly. If you cannot find this spring, you likely have a newer model that is more difficult to adjust, though this is rare. Lift up the seat. Remove the seat cousins, which hide the engine.
How fast can a factory cart go?
The factory gear most likely has a 12.5:1 ratio, which allows the cart to achieve somewhere around 14 mph. If you swap out the factory gear for one with an 8:1 gear ratio, you'll up your top end to about 20 mph.
How to make a cart faster?
Step 1. The first option to making your cart faster is to replace the electronic speed control. This will enable more voltage to pass to the motor, producing the desired result. Unfortunately, this upgrade is not inexpensive as the unit can run anywhere from $100 to $1,000. Step 2.
Can you drive a golf cart faster?
It should be noted that the golf cart you are trying to make faster may not be designed to do so. Weigh the options carefully and exercise caution whenever driving a golf cart at any speed. Remember that golf carts are not equipped with seat belts, air bags and other safety equipment that you find in automobiles.
How to change motor on Ezgo cart?
How to change the motor on a Electric EZGO: The first step is to remove the wires connecting the battery pack to ensure that the cart has no power. It is advisable to use protective gloves. Do not use wristwatch, rings or jewelry.
How to remove the engine on a 2001 Ezgo?
Here’s how you do it: You have to remove the 8 bolts holding the engine in place. You should remove all attachments such as cables, filters and ignition wires. The engine can then be pulled up. Mind the weight of the engine; it’s around 80 pounds.
How to yank a cart motor out?
Another simpler way to yank the motor out would be to remove the left side rear wheel of the cart out. You can then place the jack (if it is a hydraulic one) beneath the motor. This way, once you have removed all the cables connected to the motor and the bolts, it becomes very easy to remove the motor.
How to remove PDS motor?
Here are the steps to remove a PDS motor: You must first put the Run-Tow/Maintenance switch to Tow/Maintenance. Disconnect the wires connecting the battery. Disconnect and remove all the wires and cables connected to the motor. You should then remove the snap ring and the speed sensor from the motor end cover.
Why is it so hard to remove a golf cart motor?
On most occasions, the difficulty in removing the motor from its place in a golf cart is due to the rust that would have developed all around. It won’t come off so easily and you can’t use too much force as it may damage some of the other parts.
Can you pull an EZGO cart up?
For starters, the input shaft could be jammed or broken, making it difficult for you to pull the motor up. You can use a hammer mildly to slowly tap and pull it off the hold and pull it up. The other issue you may face with the older models of EZGO carts is where the motor could be welded to the body.