To disable the governor, you need to stop this piece from moving. Place a small rubber band on top of the T at the thickest part where the governor moves. Look behind the governor to find a small metal rod that’s permanently attached to the club car and stretch your rubber band enough to connect it to that metal rod.
How do you loosen the governor on a golf cart?
Locate the golf cart’s governor; you can find the governor by tracing the thickest cable running from the gas pedal. This cable runs through the governor on its way to the carburetor. Use a screwdriver—or in some cases a wrench—to loosen the tension on the governor’s springs.
How do you adjust the governor on a club car G16?
Wrap a zip-tie around the governor arm bolt and pull it as tight as possible. This stimulates the same effect of tightening the locknut. The following methods show you how to adjust the governor on your Club Car G16 golf cart. Turn the 10mm nut inward until you get the desired speed.
How do you remove the governor on a Toyota Corolla?
Here is how to do it. Get behind the driver’s side seat and look for a small plastic plate that’s held in place by two small screws. This whole plate will have to be taken off to get to the governor. Use a screwdriver to take off the screws. This almost always requires a Phillips head screwdriver.
How to bypass the governor on a Yamaha G1 golf cart?
The bypassing can be done by carrying out a zip-tie action on both the governor arms. The following methods show you how to adjust the governor on your Yamaha G1 golf cart.
What is a golf cart governor?
Where is the governor arm on a golf cart?
How to start a golf cart with a gas pedal?
How fast is an EZGO golf cart?
How to change the speed of a golf cart?
How to ride a golf cart at full speed?
Can you remove a golf cart governor?
See more
How do you turn off the governor on a electric golf cart?
Basically, an electric speed governor can be controlled by a tiny metal rod that's located by the clutch of your golf cart. First things first: The electric speed governor is connected to a cable. You can adjust your speed by rotating the nut in a counterclockwise rotation.
How can I make my golf cart governor faster?
Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
Where is the governor on a Club Car golf cart?
0:061:28Where Is a Golf Cart Governor Located? - YouTubeYouTubeStart of suggested clipEnd of suggested clipWell a golf cart's governor located is actually down in the motor. Compartment. Some of them theseMoreWell a golf cart's governor located is actually down in the motor. Compartment. Some of them these electric ones nowadays. Actually the governor isn't a true governor. It is a control speed.
How can I make my gas golf cart go faster?
How to Make Your Gas-Powdered Golf Cart Faster [Updated, 2022]1 Use A Better Golf Cart Battery.2 Increase Torque.3 Upgrade the Golf Cart Motor.4 Install a Torque Converter.5 Install a Higher-Performance Clutch.6 Tweak The Governor.7 Install A Cold Air Intake.8 Get Bigger Golf Cart Tires.More items...
How do you remove a speed limiter from a golf cart?
0:040:46How to remove governor on a Club Car golf cart - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the farther you bend that normally the faster it goes and then that's it basically when you wantMoreSo the farther you bend that normally the faster it goes and then that's it basically when you want to return your heart you just bend that back down and go back to normal speed.
What does removing the governor do?
Removing the governor will increase the maximum rpm of the engine, but the internal parts of the Predator 212 are designed for 3600 rpm. Generally, this isn't an issue with just the governor removal, the internal parts can usually withstand 5000 rpm without breaking apart (unless you go full throttle for too long).
How do you take the governor off a club cart?
General InstructionsDetach the cable from the carburetor. The cable is about the width of a straw. ... Follow the disconnected cable up to the governor. ... Disconnect the gas pedal cable from the governor and reroute it to the carburetor. ... Using your wrench, remove the bolt on the gas pedal shaft.
How can I make my electric golf cart go faster without upgrading?
How to Make an Electric Golf Cart Faster Without UpgradesWash Your Cart Properly. ... Inspect the Batteries. ... Refill the Battery Water. ... Check the Gas Pedal and Linkage. ... Measure the Tire Pressure. ... Charge Up Your Battery Unit. ... Lighten Up Your Cart's Weight.
How do you bypass the governor on a small engine?
1:299:11how to bypass the governor on a predator 212 engine - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then run the cable through there. And then that will allow you to throttle. Up the engine. UsingMoreAnd then run the cable through there. And then that will allow you to throttle. Up the engine. Using the governor now to bypass the governor all you have to do is.
How do you adjust the governor on a gas golf cart?
0:545:06How to Adjust an E Z Go Golf Cart Governor - WikiVideo - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut.MoreIf you are curious this is your carts carburetor loosen the small nut and tighten the larger nut. The more you tighten the larger nut the faster your cart will.
How do you adjust the governor on a Club Car golf cart?
This governor can be adjusted by adjusting the cable nut which holds the cable to the throttle lever. By making the cable longer, you effectively prevent it from pulling back the throttle lever, producing a higher top speed for your golf cart.
Why is my gas golf cart running slow?
Low Battery Usually, the most common reason golf carts slow down is when they don't get enough power output from the battery. If the battery pack charge is very low and your cart is out of power, your cart will run slow.
How to remove governor from golf cart?
How to Remove the Governor From a Golf Cart. You hit the links. The course is open in front of you as far as the eye can see. The only thing holding you back is the put-put-puttering of your golf cart. Golf carts are governed to go anywhere from 12 to 14 miles per hour. But if you've got a few minutes, some simple mechanical know-how and a wrench, ...
Where is the governor on a car?
The governor generally sits on top of the engine . This is the easiest way to find the carburetor. Once you've followed the cable up to the governor, disconnect it there as well. You can save this cable for later use or throw it away.
How to adjust a gas pedal on a cart?
Using your wrench, remove the bolt on the gas pedal shaft. Slide the shaft up so there is more play in the gas pedal. Tighten the bolt and then start the cart. You may need to adjust the gas pedal shaft a couple of times before you have it to your liking.
How fast can a golf cart go?
Golf carts are governed to go anywhere from 12 to 14 miles per hour. But if you've got a few minutes, some simple mechanical know-how and a wrench, you can double the speed of your cart and zip through your round.
What happens if you have problems with your club car?
If you have problems with your club car due to overheating or other engine troubles, the company often won’t pay to fix it. Writer Bio. Jennifer Eblin has been a full-time freelance writer since 2006. Her work has appeared on several websites, including Tool Box Tales and Zonder.
Can you go to a maximum speed on a golf cart?
If you have a golf cart, in particular a club car, you know that you can only reach a maximum speed before the car levels off. You may have seen others racing around in their club cars and wondered how they got up to such high speed. They did it by disabling their's cars' governor, a little device makes the cart stay below a specific speed.
Does a governor void a club car warranty?
If you have posted speed limits in your area, you will still have to adhere to those. The governor helps keep your club car from overheating when the engine gets too hot. If you adjust the governor you’ll need to check the engine temperature yourself. This automatically voids your warranty.
How to find the governor on a golf cart?
Locate the golf cart’s governor; you can find the governor by tracing the thickest cable running from the gas pedal. This cable runs through the governor on its way to the carburetor. Use a screwdriver—or in some cases a wrench—to loosen the tension on the governor’s springs. You have now adjusted the governor for faster speed.
Who is the writer of GolfCarCatalog.com?
GolfCarCatalog.com – “Adjusting Your Golf Cart’s Governor”. Writer Bio. Richard Kalinowski began writing professionally in 2006. He also works as a website programmer and graphic designer for several clients.
Can a golf cart be a nuisance?
In practice, golf carts can be more of a nuisance than a help, as many standard carts creep along at unbearably slow speeds. Luckily, you don’t have to stick with these standard speeds. Golf cart speed is often controlled by a device called a governor, and you can adjust the governor on a golf cart relatively easily to make the cart faster.
Can golf carts be adjusted manually?
By Richard Kalinowski. Governors limit the speed of golf carts but can be adjusted manually. In theory, golf carts make it easier for players to get across the course, saving their much-needed energy for the game. In practice, golf carts can be more of a nuisance than a help, as many standard carts creep along at unbearably slow speeds.
Where is the governor located on a club car?
If there is not an external governor with the throttle or clutch, then the governor is located inside the engine. To see this, open the hood of the club car by either unscrewing and removing the panel that covers the engine or popping open the hood like on a regular car. If the club car has a spring governor, it is located near ...
Where is the spring governor on a club car?
If the club car has a spring governor, it is located near the carburetor or it is sticking out from the differential as a pivot point. The easiest way to find it is to trace the biggest, thickest cable running from the gas pedal. Once the governor is located, use a wrench or screwdriver on the spring to loosen the tension.
Why is it dangerous to disable a governor?
It is dangerous to disable a governor completely on a club car because there is a strong chance of damage to the engine. A safer method to gain speed in a club car is simply to adjust the governor's settings. There is still a risk of damage to the engine by this method, however, as the governor is put in place by the club car manufacturer ...
How to get a club car to go faster?
If the club car has a clutch or throttle cable, then the governor is located there. Find the cable connected to the carburetor throttle lever, and adjust the cable nut so that there is more length between the lever and the nut. This makes the throttle level not pull on the cable, allowing the club car to go faster. Open the hood of the club car. ...
How to remove speed limiter from golf cart?
How do you remove a speed limiter from a golf cart? Locate the golf cart's governor; you can find the governor by tracing the thickest cable running from the gas pedal. This cable runs through the governor on its way to the carburetor. Use a screwdriver—or in some cases a wrench—to loosen the tension on the governor's springs. ...
How to adjust top speed on golf cart?
Steps. Tighten the governor spring located in the engine of most golf carts to adjust your cart's top speed. Lift up the seat. Remove the screws from the black plastic cover at the rear of the seat. Follow the thickest cable coming from the gas pedal until your find a small spring wrapped around a metal rod.
How to make a golf cart ride smoother?
How do I make my golf cart ride smoother? Springs are what give the deflection on the suspension, shocks are there to slow the deflection. To get a smooth ride use tall sidewall tires with low air pressure, springs that will hold the weight but not stiff, then the shocks can smooth the bounce of the springs.
What is a golf cart governor?
A golf cart governor is a mechanical device that helps in controlling the maximum speed of the cart when it moves on flat ground. This device prevents the engine RPMs from increasing beyond the recommended specifications.
Where is the governor arm on a golf cart?
Locate the governor arm of the golf cart. This is mounted above the rear axle housing and under the cart. Depending on the cart model, there may be a protection plate above the governor.
How to start a golf cart with a gas pedal?
Locate the gas pedal that is fitted to the governor and remove the connection. Re-route the gas pedal to the carburetor. Remove the bolt present on the shaft of the gas pedal. Slide the shaft upwards so that the gas pedal has more play. Tighten the bolt and start the golf cart.
How fast is an EZGO golf cart?
The top speed of an EZGO golf cart is usually 19.9mph and the average speed is 14mph to 15mph. With governor adjustment, the EZGO cart can go faster by 5 to 10mph.
How to change the speed of a golf cart?
Locate the spring on the differential or carburetor that helps in changing the cart speed by adjusting its tension. Increase the length of the cable that is fitted on to the body of the throttle and clutch of the two-stroke engine.
How to ride a golf cart at full speed?
Ride the cart at full speed over a course of known length. This will ensure that the governor controls the speed of the cart within factory specifications. Fasten the black plastic cover and put the seat back in place. Take care when tightening the nut. The more you tighten, the faster your cart will go.
Can you remove a golf cart governor?
It doesn’t take much time or skill to remove a golf cart governor. With some basic mechanical expertise and general-purpose tools, you can do this yourself. The process is more or less the same in all golf carts.
