Use A Hammer And Chisel
- To remove a graphite golf shaft, first determine the size of the hole that needs to be drilled. Once you have determined...
- Next, use a drill bit to create the required hole in the shaft. Make sure to use enough force while drilling so that the...
- Finally, insert a screwdriver into the end of the drill bit and twist it until it comes out of the...
How do you replace a golf club shaft?
How To Re-Shaft Your Steel Golf Clubs
- Carefully clamp the shaft into a vise using a Shaft Vise Clamp. ...
- When removing steel shafts from clubheads, use a torch to heat the hosel. ...
- After 30 seconds of heating, with your gloved hands grasp the head and twist/pull the head. ...
- Using a wire brush remove excess epoxy from the inside of the hosel.
How to remove a golf shaft without a puller?
How to Remove a Golf Shaft From the Head
- Remove the ferrule. The ferrule is the small plastic band that sits just above the hosel. ...
- Place the club in a vise to position it for shaft removal. The club should lie horizontally. ...
- Heat the glue inside the hosel. The hosel is the area where the shaft fits into the clubhead. ...
- Clean excess glue out of the hosel to make a comfortable fit for the new shaft. ...
How do I clean up golf club shafts?
Prevention is Better Than Cure
- Wipe your clubs down with cotton after every round
- Wipe your clubs with a multipurpose lubricant in every few months
- Never store them in a humid location i.e. garage, corner of a storeroom.
- Closely monitor the clubs once a month.
- Spray rust remover on metal club heads and shafts. ...
- Dry out properly before storing your clubs if they get wet.
Can you change a shaft from graphite to steel?
Steel iron shafts have been the standard for decades, but that doesn't mean they should be the standard for you. Unless you're a pro, you should take a serious look at switching out to graphite.
How do you remove a graphite shaft at home?
0:353:50How To - Pull a graphite golf shaft - YouTubeYouTubeStart of suggested clipEnd of suggested clipAgain using a butane torch you can actually really focus the heat which is a lot better than sayMoreAgain using a butane torch you can actually really focus the heat which is a lot better than say trying to use a heat gun which could end up damaging. The fibers of the golf shaft.
Can you pull a graphite shaft without a shaft puller?
Well, the general process for pulling a graphite shaft is just about the same, but there are a few key differences. You need to take more care and HAVE to use a shaft puller. Otherwise, your new fancy and expensive exotic shaft could be at serious risk for major damage.
Can you reuse a graphite shaft?
Along the lines of what fupresti said, as long as they're pulled properly you should be able to reuse a graphite shaft indefinitely. The only way a graphite shaft will become unusable aside from some freak accidents is by human error in part of the build or an out of control temper on the course.
How do you remove a graphite shaft tip?
8:1117:13How To remove / Install a Golf shaft Adapter - YouTubeYouTubeStart of suggested clipEnd of suggested clipThere's screw type and it's the kind where you turn it either with a wrench or or a handle that'llMoreThere's screw type and it's the kind where you turn it either with a wrench or or a handle that'll get you in there of which golf mechanics does very very good on that reverse thrust unit very smooth.
Can you remove a golf shaft with a hair dryer?
Another alternative heat source I've had success with (literally twice) was a hair dryer. I read about golfers packing prized putters in their carry-on luggage, re-shafting at their hotel, and then removing the head with the hotel hair dryer prior to traveling home. Following that, I tried it and it worked.
How do I remove a shaft adapter without a puller?
1:594:14Simple Taylor Made shaft adapter removal 30 sec without shaft pullerYouTubeStart of suggested clipEnd of suggested clipAll right take the head on see that moves really easy and so you just keep kind of twisting. AndMoreAll right take the head on see that moves really easy and so you just keep kind of twisting. And pulling keep the head locked in and eventually it will come all the way. Off.
How do you remove a golf shaft?
1:015:14Golf Club Repair - Part 1 - Removing a shaft & cleaning the hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro willMoreBasically. Get your electric heater heat it up just a little bit in that little plastic Ferro will come right off you can almost pull it off with your hands once it gets softened.
Can I change my graphite shafts to steel?
While this trend has been going on for a while now, it has really accelerated in the last few months.
Can you take shaft out of irons?
0:042:32How To Remove A Steel Golf Shaft From A Golf Club - YouTubeYouTubeStart of suggested clipEnd of suggested clipClub making repairs that you can make that's removing a steel shaft from an iron ore wedge. NowMoreClub making repairs that you can make that's removing a steel shaft from an iron ore wedge. Now there's lots of ways to do this but in a few tools as well.
How do you replace a graphite shaft?
4:297:38How to Install Graphite Golf Shafts - YouTubeYouTubeStart of suggested clipEnd of suggested clipRemove the head and place some epoxy inside the hosel dip the tip of the shaft into the epoxy mix.MoreRemove the head and place some epoxy inside the hosel dip the tip of the shaft into the epoxy mix. And then install into the head rotate.
How do you use a shaft puller?
2:226:40pulling a graphite shaft 2016 - YouTubeYouTubeStart of suggested clipEnd of suggested clipQuick. Okay after we put the heat to it you want to put it into the puller really fast and then youMoreQuick. Okay after we put the heat to it you want to put it into the puller really fast and then you want to hold on to the head that you just got out.
How do you remove a broken graphite shaft from club head?
0:483:31How to Remove a Graphite Shaft Broken Off at the Hosel - YouTubeYouTubeStart of suggested clipEnd of suggested clipBy scads to protect the club. Head I want to clamp it make sure to clamp it tight but not too tightMoreBy scads to protect the club. Head I want to clamp it make sure to clamp it tight but not too tight if I'm gonna crush the top of the housing. Now you're gonna need a few other things.
How to remove graphite shaft?
One method to remove a graphite shaft is to remove the ferrule, cut the shaft off at the hosel and drill the remaining part out of the hosel. However, on modern drivers, fairways and hybrids which are nearly all hollow inside, could potentially could push material into the cavity of the head and cause it to rattle.
How many times can you remove graphite from a clubhead?
Sometimes these steps will have to be repeated as many as 3 or 4 times (or more) before successfully removing the graphite shaft from the clubhead, especially for titanium and aluminum clubheads. The more pressure that the shaft puller applies the less heat it takes to remove the shaft from the clubhead.
What is a graphite shaft made of?
A graphite shaft is made from many layers of graphite pre-preg or long continuous strands of carbon fiber wrapped around a forming mandrel. To hold the layers or strands together, an epoxy resin is used. This same epoxy resin is not much different from the epoxy that is used to hold the head onto the shaft. In order to remove the head ...
How long to reheat a golf club?
If the clubhead does not come off at this point, reheat for a period of 25-30 seconds. Remember, you can always reheat the hosel, but you can’t remove heat if you heat the club too long. Continue this method of heating for 25 second intervals until the shaft puller has forced the clubhead from the shaft.
How much does a shaft puller cost?
Shaft pullers can range anywhere from around $20 for a devise that looks like a modified pry bar (you still need a vise and shaft clamp) to several hundred dollars for a hydraulic model. Regardless, invest in a good shaft puller if you are repairing clubs in any sort of volume. Remember how much shafts cost again.
How to protect a carbon head?
If this is the case, go to you local welding supply center and get a bottle of a product called Cool Gel. This is very cool stuff! Just spray it on the carbon surface only and it will protect it from any wayward heat like an accidental pass with the torch. When you are done, you can just wipe the head with a wet paper towel or rag to remove the gel.
When to remove head from shaft?
You are now ready to apply heat to the head for the purpose of removing the head from the shaft. It is best to remove the shaft as soon as the epoxy breaks loose. By doing so, this will limit the possibility of heat penetrating into the shaft and causing it to break down.
How to loosen a club shaft?
There are two ways to do this step. One way to loosen the shaft from the clubhead is to heat the hosel, or connector, of the clubhead with a blow torch until the epoxy that is used to bond them together becomes liquid. Be sure that you wear protective glasses while doing this process. The second way is to cut the shaft right above the hosel ...
How long does it take for epoxy to set on a golf club?
Allow about 24 hours for the epoxy to completely set before you finish your golf club. Decide on the length of the club, then mark it where the cut should be made. Since the graphite shaft might shatter when cut, put on a few layers of tape on the cut line before you use a band saw to cut it.
How to put a clubhead on a hosel?
Carefully place the tip of the shaft inside the hosel, ad twist the clubhead slightly to be sure that both the hosel and the shaft are covered thoroughly. Finally, pull the ferrule down to its proper position.
How to use epoxy on a hosel?
Mix a small amount of epoxy and spread it liberally inside the hosel, making sure that all the surfaces are covered. Do the same with the tip of the shaft; and if a ferrule, or a piece of plastic that goes onto the shaft and butts against the hosel, is to be used, put a small amount of epoxy on it an place it on the shaft.
Can you remove a graphite shaft?
Actually, removing a graphite shaft, then replacing it, are easy to do if you follow these simple steps. Soon you will have virtually a new club, and dreams of lowering your score might be a reality.
Can you pull a pro launch shaft by hand?
I have pulled a few by hand, never anything high end so if it didn't work no biggie. I did mess up the tip of a Pro Launch shaft, just trimmed it and used it in a 5 wood. Did another that was a mess, had to drill it out and throw the shaft away, but I have had several others where I had no issues. It's risky, but it can be done.
Can you pull graphite shafts without a puller?
Pulling a graphite shaft without a shaft puller is almost a guaranteed way to ruin a shaft. You might get lucky and not damage it, but not something I would risk. If someone said here is a shaft to use and by the way, I pulled it by hand, I would pass on it.
Remove the Grip
The first things to do is to remove the grip tape from the golf club [how to remove grip tape from golf club]. This will make it easier to cut the shaft. You can use a cutter to slice the grip from the top and slowly peel it off the club. The specific process can differ, which will depend on the material of the grip.
Measure the Shaft
With the grip now off the golf club, the next step is to take the appropriate measurement. Use a measuring tape and run it from the top to the bottom of the shaft. Mark the specific spot where the measurement ends. You can do this with a marker or by wrapping the tape around the tip. The measurements should be as precise as possible.
Cut the Shaft
Now comes the most important part of the task. Before cutting the shaft, make sure that it is in a stable position. Some might think that they can cut by holding the shaft with one hand, but this isn’t the case. For your safety and to make the cut more accurate, we recommend placing the golf club in a vise.
Wrap a Grip Tape
Once you are done cutting, the next step is to wrap it using your grip of choice. Pick a material you are comfortable with. This is important since it is the part that you will be holding, and hence, it will affect how you swing the club. Also, it must absorb vibration, making sure of your highest level of comfort, even during aggressive shots.
How to remove tape from golf club?
It should take approximately 10 minutes to heat the shaft. Focus the heat gun on the grip area of the shaft where the tape is located .
What happens if your golf grips are worn out?
If your grips are worn out, then your scores will begin to suffer on the course due to the loss of control of your golf shots. Over the life of your clubs, you will need to replace the grips.
How to tape a grip?
Apply double-sided tape to the length of the grips by wrapping the tape around the shaft.
Can you remove grip tape from graphite shafts?
If you choose to do the grip replacement yourself, a common problem that arises is removing the grip tape from graphite shafts during the replacement process. Unlike steel shafted clubs, graphite shafts can be damaged much easier during the tape removal process and require special attention.
